A user may lower the max_sectors_kb setting in sysfs to accommodate
certain workloads. Previously we would always set the max I/O size to
either the block layer default or the optional preferred I/O size
reported by the device.
Keep the current heuristics for the initial setting of max_sectors_kb.
For subsequent invocations, only update the current queue limit if it
exceeds the capabilities of the hardware.
Cc: <stable@vger.kernel.org>
Reported-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SBC-4 states:
"A MAXIMUM UNMAP LBA COUNT field set to a non-zero value indicates the
maximum number of LBAs that may be unmapped by an UNMAP command"
"A MAXIMUM WRITE SAME LENGTH field set to a non-zero value indicates
the maximum number of contiguous logical blocks that the device server
allows to be unmapped or written in a single WRITE SAME command."
Despite the spec being clear on the topic, some devices incorrectly
expect WRITE SAME commands with the UNMAP bit set to be limited to the
value reported in MAXIMUM UNMAP LBA COUNT in the Block Limits VPD.
Implement a blacklist option that can be used to accommodate devices
with this behavior.
Cc: <stable@vger.kernel.org>
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After series of changes around WRITE_SAME and UNMAP setup we ended up
with leftover unnecessary condition. Remove it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gd->minors has been set when call alloc_disk() in sd_probe.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that gcc reports the following warning when
building with W=1:
drivers/scsi/sd.c:315:10: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (val >= 0 && val <= T10_PI_TYPE3_PROTECTION)
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that smatch reports the following:
drivers/scsi/sd.c:3540: sd_suspend_common() warn: inconsistent indenting
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before scsi_prep_fn() calls the ULP .init_command() callback
function it stores the SCSI command pointer in request.special.
This means that the SCpnt = rq->special assignments in the sd
and sr drivers assign a pointer to itself. Hence convert these
two assignment statements into warning statements.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Releasing a zone write lock only when the write commnand that acquired
the lock completes can cause deadlocks due to potential command
reordering if the lock owning request is requeued and not executed. This
problem exists only with the scsi-mq path as, unlike the legacy path,
requests are moved out of the dispatch queue before being prepared and
so before locking a zone for a write command.
Since sd_uninit_cmnd() is now always called when a request is requeued,
call sd_zbc_write_unlock_zone() from that function for write requests
that acquired a zone lock instead of from sd_done(). Acquisition of a zone
lock by a write command is indicated using the new command
flag SCMD_ZONE_WRITE_LOCK.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=D9QX
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (276 commits)
qla2xxx: Fix NVMe entry_type for iocb packet on BE system
scsi: qla2xxx: avoid unused-function warning
scsi: snic: fix a couple of spelling mistakes/typos
scsi: qla2xxx: fix a bunch of typos and spelling mistakes
scsi: lpfc: don't double count abort errors
scsi: lpfc: spin_lock_irq() is not nestable
scsi: hisi_sas: optimise DMA slot memory
scsi: ibmvfc: constify dev_pm_ops structures.
scsi: ibmvscsi: constify dev_pm_ops structures.
scsi: cxlflash: Update debug prints in reset handlers
scsi: cxlflash: Update send_tmf() parameters
scsi: cxlflash: Avoid double free of character device
scsi: Add STARGET_CREATED_REMOVE state to scsi_target_state
scsi: ses: do not add a device to an enclosure if enclosure_add_links() fails.
scsi: ufs: flush eh_work when eh_work scheduled.
scsi: qla2xxx: Protect access to qpair members with qpair->qp_lock
scsi: sun_esp: fix device reference leaks
scsi: fnic: changing queue command to return result DID_IMM_RETRY when rport is init
scsi: fnic: correct speed display and add support for 25,40 and 100G
scsi: fnic: added timestamp reporting in fnic debug stats
...
Pull libata updates from Tejun Heo:
- Christoph added support for TCG OPAL self encrypting disks
- Minwoo added support for ATA PASS-THROUGH(32)
- Linus Walleij removed spurious drvdata assignments in some drivers
- Support for a few new device and other fixes
* 'for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (33 commits)
sd: add support for TCG OPAL self encrypting disks
libata: fix build warning from unused goto label
libata: Support for an ATA PASS-THROUGH(32) command.
ahci: Add Device ID for ASMedia 1061R and 1062R
sata_via: Enable optional hotplug on VT6420
ata: ahci_brcm: Avoid writing to read-only registers
libata: Add the AHCI_HFLAG_NO_WRITE_TO_RO flag
libata: Add the AHCI_HFLAG_YES_ALPM flag
ata: ftide010: fix resource printing
libata: make the function name in comment match the actual function
ata: sata_rcar: make of_device_ids const.
ata: pata_octeon_cf: make of_device_ids const.
libata: Convert bare printks to pr_cont
libahci: wrong comments in ahci_do_softreset()
ata: declare ata_port_info structures as const
ata: Add driver for Faraday Technology FTIDE010
ata: Add DT bindings for the Gemini SATA bridge
ata: Add DT bindings for Faraday Technology FTIDE010
libata: implement SECURITY PROTOCOL IN/OUT
libata: factor out a ata_identify_page_supported helper
...
Just wire up the generic TCG OPAL infrastructure to the SCSI disk driver
and the Security In/Out commands.
Note that I don't know of any actual SCSI disks that do support TCG OPAL,
but this is required to support ATA disks through libata.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoid unnecessary snprintf() when formatting variables for display in
sysfs and switch to sysfs_match_string() for validating user input.
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Serializing SCSI device state changes avoids that two state changes can
occur concurrently, e.g. the state changes in scsi_target_block() and
__scsi_remove_device(). This serialization is essential to make patch
"Make __scsi_remove_device go straight from BLOCKED to DEL" work
reliably.
Enable this mechanism for all scsi_target_*block() callers but not for
the scsi_internal_device_unblock() calls from the mpt3sas driver because
that driver can call scsi_internal_device_unblock() from atomic context.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some external hard drives don't support the sync command even though the
hard drive has write cache enabled. In this case, upon suspend request,
sync cache failures are ignored if the error code in the sense header is
ILLEGAL_REQUEST. There's not much we can do for these drives, so we
shouldn't fail to suspend for this error case. The drive may stay
powered if that's the setup for the port it's plugged into.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For a zoned block device, sd_zbc_complete() handles zone write unlock on
completion of a REQ_OP_WRITE_ZEROES command but the zone write locking
is missing from sd_setup_write_zeroes_cmnd(). This patch fixes this
problem by locking the target zone of a REQ_OP_WRITE_ZEROES request.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_io_init() may fail, leaving a zone of a zoned block device locked.
Fix this by properly unlocking the write same request target zone if
scsi_io_init() fails.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
Rename sd_zbc_setup_write_cmnd() to sd_zbc_write_lock_zone() to be clear
about what the function actually does. To be consistent, also rename
sd_zbc_cancel_write_cmnd() to sd_zbc_write_unlock_zone().
No functional change is introduced by this patch.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a switch for the sense key, and remove two pointless variables that
are only used once.
[mkp: Added UNMAP comment and removed good_bytes based on comment from
Damien]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-shuffle the code to be more efficient by not initializing variables
upfront (i.e. do it only when necessary). Also replace the do_div calls
with calls to sectors_to_logical().
No functional change is introduced by this patch.
[mkp: bytes_to_logical()]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix argument names and description of function documentation comments.
No functional change is introduced by this patch.
[mkp: verbify]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is seven small fixes which are all for user visible issues that
fortunately only occur in rare circumstances. The most serious is the
sr one in which QEMU can cause us to read beyond the end of a buffer
(I don't think it's exploitable, but just in case). The next is the
sd capacity fix which means all non 512 byte sector drives greater
than 2TB fail to be correctly sized. The rest are either in new
drivers (qedf) or on error legs.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vOpC
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is seven small fixes which are all for user visible issues that
fortunately only occur in rare circumstances.
The most serious is the sr one in which QEMU can cause us to read
beyond the end of a buffer (I don't think it's exploitable, but just
in case).
The next is the sd capacity fix which means all non 512 byte sector
drives greater than 2TB fail to be correctly sized.
The rest are either in new drivers (qedf) or on error legs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
scsi: aacraid: fix PCI error recovery path
scsi: sd: Fix capacity calculation with 32-bit sector_t
scsi: qla2xxx: Add fix to read correct register value for ISP82xx.
scsi: qedf: Fix crash due to unsolicited FIP VLAN response.
scsi: sr: Sanity check returned mode data
scsi: sd: Consider max_xfer_blocks if opt_xfer_blocks is unusable
Separating discards and zeroout operations allows us to remove the LBPRZ
block zeroing constraints from discards and honor the device preferences
for UNMAP commands.
If supported by the device, we'll also choose UNMAP over one of the
WRITE SAME variants for discards.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that zeroout and discards are distinct operations we need to
separate the policy of choosing the appropriate command. Create a
zeroing_mode which can be one of:
write: Zeroout assist not present, use regular WRITE
writesame: Allow WRITE SAME(10/16) with a zeroed payload
writesame_16_unmap: Allow WRITE SAME(16) with UNMAP
writesame_10_unmap: Allow WRITE SAME(10) with UNMAP
The last two are conditional on the device being thin provisioned with
LBPRZ=1 and LBPWS=1 or LBPWS10=1 respectively.
Whether to set the UNMAP bit or not depends on the REQ_NOUNMAP flag. And
if none of the _unmap variants are supported, regular WRITE SAME will be
used if the device supports it.
The zeroout_mode is exported in sysfs and the detected mode for a given
device can be overridden using the string constants above.
With this change in place we can now issue WRITE SAME(16) with UNMAP set
for block zeroing applications that require hard guarantees and
logical_block_size granularity. And at the same time use the UNMAP
command with the device's preferred granulary and alignment for discard
operations.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Try to use a write same with unmap bit variant if the device supports it
and the caller allows for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Split sd_setup_discard_cmnd into one function per provisioning type. While
this creates some very slight duplication of boilerplate code it keeps the
code modular for additions of new provisioning types, and for reusing the
write same functions for the upcoming scsi implementation of the Write Zeroes
operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Cc: <stable@vger.kernel.org>
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.
[mkp: tweaked to avoid setting rw_max twice and added typecast]
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ca369d51b3 ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If sd_eh_action() decides to take the device offline there is
no point in returning FAILED, as taking the device offline
is the ultimate step in SCSI EH anyway.
So further escalation via SCSI EH is not likely to make a
difference and we can as well return SUCCESS.
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current medium access timeout counter will be increased for
each command, so if there are enough failed commands we'll hit
the medium access timeout for even a single device failure and
the following kernel message is displayed:
sd H:C:T:L: [sdXY] Medium access timeout failure. Offlining disk!
Fix this by making the timeout per EH run, ie the counter will
only be increased once per device and EH run.
Fixes: 18a4d0a ("[SCSI] Handle disk devices which can not process medium access commands")
Cc: Ewan Milne <emilne@redhat.com>
Cc: Lawrence Obermann <loberman@redhat.com>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a rather large set of fixes. The bulk are for lpfc correcting
a lot of issues in the new NVME driver code which just went in in the
merge window. The others are: fix a hang in the vmware paravirt
driver caused by incorrect handling of the new MSI vector allocation.
A long standing bug in storvsc, which recent block changes turned from
being a harmless annoyance into a hang and yet more fallout (in
mpt3sas) from the changes to device blocking. The remainder are small
fixes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYyXW+AAoJEAVr7HOZEZN4yzIP/R2qDzwoXw3dl5xHs2AQuxWU
P7mbUqtN2meU0klIKNCaYq6WO797WvGblSldrPwB08M7QOg8vy7boNiCYmwdEs6W
Ftihj99OwEp0598MldNw1hBtMqjJ1WSu/kLK/I3pjLjltyPbQunuvaEwSNvxD1r7
8BRmngYLFPb3KQDSO74ILBdZ5DqsriIXDHlngKSKfrpjO5IWXHrmzhZTmU2qpE40
H4C4+Kn3/iZKGRiMm4rsikRDEGty9aVo7f4CIrwWslLkaJWf/AS4Kf3rd5qqclRj
crjP/axqXheuwggKaHNhnxX5oSGt61ZCH9lGMmSNV/q6pUtNsrhO2uZuBIP0vtDB
y7Pfw0Z3MGnbsOmBhZLRnUYC9PgSZPysy3TuS6/BgGx2ZFPnFxXjA1T73YaUil9q
zcCOV2E7WHjIFGrpF2jNmoGsh1360TUOjg8YXdLi8pC2sEqSU331nvB5W9xAw3EG
ewusZFetumxV8pykSyuDknU5gAMVYhHv+I+eNP8SB0eUZTLeKlcZpWIt3QYSYRdJ
KbCc4CSi28J+DghB86eRZC64QqFiYMP546zUPpD1Enh/HXtVrTYzRN9/Qwo2FJRZ
s5E3aC6tPceSuOmqn4aL9+Il7NXDj1Y/M9Qwe6Dzjp7q8hLCb7J1TWY3G5ImBWI7
TfdyBrvZerqpxga+6j5g
=0mha
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a rather large set of fixes. The bulk are for lpfc correcting
a lot of issues in the new NVME driver code which just went in in the
merge window.
The others are:
- fix a hang in the vmware paravirt driver caused by incorrect
handling of the new MSI vector allocation
- long standing bug in storvsc, which recent block changes turned
from being a harmless annoyance into a hang
- yet more fallout (in mpt3sas) from the changes to device blocking
The remainder are small fixes and updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (34 commits)
scsi: lpfc: Add shutdown method for kexec
scsi: storvsc: Workaround for virtual DVD SCSI version
scsi: lpfc: revise version number to 11.2.0.10
scsi: lpfc: code cleanups in NVME initiator discovery
scsi: lpfc: code cleanups in NVME initiator base
scsi: lpfc: correct rdp diag portnames
scsi: lpfc: remove dead sli3 nvme code
scsi: lpfc: correct double print
scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT
scsi: lpfc: Rework lpfc Kconfig for NVME options
scsi: lpfc: add transport eh_timed_out reference
scsi: lpfc: Fix eh_deadline setting for sli3 adapters.
scsi: lpfc: add NVME exchange aborts
scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport
scsi: lpfc: Fix IO submission if WQ is full
scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem
scsi: lpfc: Fix RCTL value on NVME LS request and response
scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters
scsi: lpfc: fix missing spin_unlock on sql_list_lock
scsi: lpfc: don't dereference dma_buf->iocbq before null check
...
This reverts commit 0dba1314d4. It causes
leaking of device numbers for SCSI when SCSI registers multiple gendisks
for one request_queue in succession. It can be easily reproduced using
Omar's script [1] on kernel with CONFIG_DEBUG_TEST_DRIVER_REMOVE.
Furthermore the protection provided by this commit is not needed anymore
as the problem it was fixing got also fixed by commit 165a5e22fa
"block: Move bdi_unregister() to del_gendisk()".
[1]: http://marc.info/?l=linux-block&m=148554717109098&w=2
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit <f2e767bb5d6e> ("mpt3sas: Force request partial completion
alignment") was not considering the case of commands not operating on
logical block size units (e.g. REQ_OP_ZONE_REPORT and its 64B aligned
partial replies). In this case, forcing alignment of resid to the device
logical block size can break the command result, e.g. in the case of
REQ_OP_ZONE_REPORT, the exact number of zone reported by the device.
Move the partial completion alignement check of mpt3sas to a generic
implementation in sd_done(). The check is added within the default
section of the initial req_op() switch case so that the report and reset
zone commands are ignored. In addition, as sd_done() is not called for
passthrough requests, resid corrections are not done as intended by the
initial mpt3sas patch.
Fixes: f2e767bb5d ("mpt3sas: Force request partial completion alignment")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And switch all callers to use scsi_execute instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove bogus evaluations of retval and sshdr when the device is offline,
and fix a possible NULL pointer dereference by allocating the 8 byte
sized sense header on stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an allocation failure of gd, the current exit path is via
out_free_devt which leaves sdpk still allocated and hence it gets
leaked. Fix this by correcting the order of resource free'ing with a
change in the error exit path labels.
Detected by CoverityScan, CID#1399519 ("Resource Leak")
Fixes: 0dba1314d4 ("scsi, block: fix duplicate bdi name registration crashes")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following sparse warning:
drivers/scsi/sd.c:3087:6: warning:
symbol 'sd_devt_release' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ). There's also an assortment of minor fixes and the
major update of switching a bunch of drivers to pci_alloc_irq_vectors
from Christoph.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cBQx
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ...).
There's also an assortment of minor fixes and the major update of
switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
scsi: megaraid_sas: handle dma_addr_t right on 32-bit
scsi: megaraid_sas: array overflow in megasas_dump_frame()
scsi: snic: switch to pci_irq_alloc_vectors
scsi: megaraid_sas: driver version upgrade
scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
scsi: megaraid_sas: Indentation and smatch warning fixes
scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
scsi: megaraid_sas: Increase internal command pool
scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
scsi: megaraid_sas: update can_queue only if the new value is less
scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
...
Warnings of the following form occur because scsi reuses a devt number
while the block layer still has it referenced as the name of the bdi
[1]:
WARNING: CPU: 1 PID: 93 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/devices/virtual/bdi/8:192'
[..]
Call Trace:
dump_stack+0x86/0xc3
__warn+0xcb/0xf0
warn_slowpath_fmt+0x5f/0x80
? kernfs_path_from_node+0x4f/0x60
sysfs_warn_dup+0x62/0x80
sysfs_create_dir_ns+0x77/0x90
kobject_add_internal+0xb2/0x350
kobject_add+0x75/0xd0
device_add+0x15a/0x650
device_create_groups_vargs+0xe0/0xf0
device_create_vargs+0x1c/0x20
bdi_register+0x90/0x240
? lockdep_init_map+0x57/0x200
bdi_register_owner+0x36/0x60
device_add_disk+0x1bb/0x4e0
? __pm_runtime_use_autosuspend+0x5c/0x70
sd_probe_async+0x10d/0x1c0
async_run_entry_fn+0x39/0x170
This is a brute-force fix to pass the devt release information from
sd_probe() to the locations where we register the bdi,
device_add_disk(), and unregister the bdi, blk_cleanup_queue().
Thanks to Omar for the quick reproducer script [2]. This patch survives
where an unmodified kernel fails in a few seconds.
[1]: https://marc.info/?l=linux-scsi&m=147116857810716&w=4
[2]: http://marc.info/?l=linux-block&m=148554717109098&w=2
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Reported-by: Omar Sandoval <osandov@osandov.com>
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
->done can only be called for fs requests, so no need to check again here.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In sd.c there are two comment references to 'struct scsi_device *sdp' as
an argument. One of the references has a typo and the other should be a
reference to 'struct device *dev' instead.
Fixed by correcting the typo in the first and changing the explanation
in the second.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of 12 fixes including the mpt3sas one that was causing
hangs on ATA passthrough. The others are a couple of zoned block
device fixes, a SAS device detection bug which lead to SATA drives not
being matched to bays, two qla2xxx MSI fixes, a qla2xxx req for rsp
confusion caused by cut and paste, and a few other minor fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8y3/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 12 fixes including the mpt3sas one that was causing
hangs on ATA passthrough.
The others are a couple of zoned block device fixes, a SAS device
detection bug which lead to SATA drives not being matched to bays, two
qla2xxx MSI fixes, a qla2xxx req for rsp confusion caused by cut and
paste, and a few other minor fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: fix hang on ata passthrough commands
scsi: lpfc: Set elsiocb contexts to NULL after freeing it
scsi: sd: Ignore zoned field for host-managed devices
scsi: sd: Fix wrong DPOFUA disable in sd_read_cache_type
scsi: bfa: fix wrongly initialized variable in bfad_im_bsg_els_ct_request()
scsi: ses: Fix SAS device detection in enclosure
scsi: libfc: Fix variable name in fc_set_wwpn
scsi: lpfc: avoid double free of resource identifiers
scsi: qla2xxx: remove irq_affinity_notifier
scsi: qla2xxx: fix MSI-X vector affinity
scsi: qla2xxx: Fix apparent cut-n-paste error.
scsi: qla2xxx: Get mutex lock before checking optrom_state
