Add a function that can be called by device drivers to set "offload" or
"trap" indication on nexthop buckets following nexthop notifications and
other changes such as a neighbour becoming invalid.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the following notifications towards drivers:
- NEXTHOP_EVENT_REPLACE, when a resilient nexthop group is created.
- NEXTHOP_EVENT_BUCKET_REPLACE any time there is a change in assignment of
next hops to hash table buckets. That includes replacements, deletions,
and delayed upkeep cycles. Some bucket notifications can be vetoed by the
driver, to make it possible to propagate bucket busy-ness flags from the
HW back to the algorithm. Some are however forced, e.g. if a next hop is
deleted, all buckets that use this next hop simply must be migrated,
whether the HW wishes so or not.
- NEXTHOP_EVENT_RES_TABLE_PRE_REPLACE, before a resilient nexthop group is
replaced. Usually the driver will get the bucket notifications as well,
and could veto those. But in some cases, a bucket may not be migrated
immediately, but during delayed upkeep, and that is too late to roll the
transaction back. This notification allows the driver to take a look and
veto the new proposed group up front, before anything is committed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment, there is only one type of next-hop group: an mpath group,
which implements the hash-threshold algorithm.
To select a next hop, hash-threshold algorithm first assigns a range of
hashes to each next hop in the group, and then selects the next hop by
comparing the SKB hash with the individual ranges. When a next hop is
removed from the group, the ranges are recomputed, which leads to
reassignment of parts of hash space from one next hop to another. While
there will usually be some overlap between the previous and the new
distribution, some traffic flows change the next hop that they resolve to.
That causes problems e.g. as established TCP connections are reset, because
the traffic is forwarded to a server that is not familiar with the
connection.
Resilient hashing is a technique to address the above problem. Resilient
next-hop group has another layer of indirection between the group itself
and its constituent next hops: a hash table. The selection algorithm uses a
straightforward modulo operation to choose a hash bucket, and then reads
the next hop that this bucket contains, and forwards traffic there.
This indirection brings an important feature. In the hash-threshold
algorithm, the range of hashes associated with a next hop must be
continuous. With a hash table, mapping between the hash table buckets and
the individual next hops is arbitrary. Therefore when a next hop is deleted
the buckets that held it are simply reassigned to other next hops. When
weights of next hops in a group are altered, it may be possible to choose a
subset of buckets that are currently not used for forwarding traffic, and
use those to satisfy the new next-hop distribution demands, keeping the
"busy" buckets intact. This way, established flows are ideally kept being
forwarded to the same endpoints through the same paths as before the
next-hop group change.
In a nutshell, the algorithm works as follows. Each next hop has a number
of buckets that it wants to have, according to its weight and the number of
buckets in the hash table. In case of an event that might cause bucket
allocation change, the numbers for individual next hops are updated,
similarly to how ranges are updated for mpath group next hops. Following
that, a new "upkeep" algorithm runs, and for idle buckets that belong to a
next hop that is currently occupying more buckets than it wants (it is
"overweight"), it migrates the buckets to one of the next hops that has
fewer buckets than it wants (it is "underweight"). If, after this, there
are still underweight next hops, another upkeep run is scheduled to a
future time.
Chances are there are not enough "idle" buckets to satisfy the new demands.
The algorithm has knobs to select both what it means for a bucket to be
idle, and for whether and when to forcefully migrate buckets if there keeps
being an insufficient number of idle buckets.
There are three users of the resilient data structures.
- The forwarding code accesses them under RCU, and does not modify them
except for updating the time a selected bucket was last used.
- Netlink code, running under RTNL, which may modify the data.
- The delayed upkeep code, which may modify the data. This runs unlocked,
and mutual exclusion between the RTNL code and the delayed upkeep is
maintained by canceling the delayed work synchronously before the RTNL
code touches anything. Later it restarts the delayed work if necessary.
The RTNL code has to implement next-hop group replacement, next hop
removal, etc. For removal, the mpath code uses a neat trick of having a
backup next hop group structure, doing the necessary changes offline, and
then RCU-swapping them in. However, the hash tables for resilient hashing
are about an order of magnitude larger than the groups themselves (the size
might be e.g. 4K entries), and it was felt that keeping two of them is an
overkill. Both the primary next-hop group and the spare therefore use the
same resilient table, and writers are careful to keep all references valid
for the forwarding code. The hash table references next-hop group entries
from the next-hop group that is currently in the primary role (i.e. not
spare). During the transition from primary to spare, the table references a
mix of both the primary group and the spare. When a next hop is deleted,
the corresponding buckets are not set to NULL, but instead marked as empty,
so that the pointer is valid and can be used by the forwarding code. The
buckets are then migrated to a new next-hop group entry during upkeep. The
only times that the hash table is invalid is the very beginning and very
end of its lifetime. Between those points, it is always kept valid.
This patch introduces the core support code itself. It does not handle
notifications towards drivers, which are kept as if the group were an mpath
one. It does not handle netlink either. The only bit currently exposed to
user space is the new next-hop group type, and that is currently bounced.
There is therefore no way to actually access this code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- RTM_NEWNEXTHOP et.al. that handle resilient groups will have a new nested
attribute, NHA_RES_GROUP, whose elements are attributes NHA_RES_GROUP_*.
- RTM_NEWNEXTHOPBUCKET et.al. is a suite of new messages that will
currently serve only for dumping of individual buckets of resilient next
hop groups. For nexthop group buckets, these messages will carry a nested
attribute NHA_RES_BUCKET, whose elements are attributes NHA_RES_BUCKET_*.
There are several reasons why a new suite of messages is created for
nexthop buckets instead of overloading the information on the existing
RTM_{NEW,DEL,GET}NEXTHOP messages.
First, a nexthop group can contain a large number of nexthop buckets (4k
is not unheard of). This imposes limits on the amount of information that
can be encoded for each nexthop bucket given a netlink message is limited
to 64k bytes.
Second, while RTM_NEWNEXTHOPBUCKET is only used for notifications at
this point, in the future it can be extended to provide user space with
control over nexthop buckets configuration.
- The new group type is NEXTHOP_GRP_TYPE_RES. Note that nexthop code is
adjusted to bounce groups with that type for now.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of resilient nexthop groups, there will be two types
of multipath groups: the current hash-threshold "mpath" ones, and resilient
groups. Both are multipath, but to determine the fact, the system needs to
consider two flags. This might prove costly in the datapath. Therefore,
introduce a new flag, that should be set for next-hop groups that have more
than one nexthop, and should be considered multipath.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited function currently uses rtnl_dereference() to get nh_info from a
handed-in nexthop. However, under the resilient hashing scheme, this
function will not always be called under RTNL, sometimes the mutual
exclusion will be achieved differently. Therefore move the nh_info
extraction from the function to its callers to make it possible to use a
different synchronization guarantee.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, replace assumes that the new group that is given is a
fully-formed object. But mpath groups really only have one attribute, and
that is the constituent next hop configuration. This may not be universally
true. From the usability perspective, it is desirable to allow the replace
operation to adjust just the constituent next hop configuration and leave
the group attributes as such intact.
But the object that keeps track of whether an attribute was or was not
given is the nh_config object, not the next hop or next-hop group. To allow
(selective) attribute updates during NH group replacement, propagate `cfg'
to replace_nexthop() and further to replace_nexthop_grp().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As far as user space is concerned, blackhole nexthops do not have a
nexthop device and therefore should not be affected by the
administrative or carrier state of any netdev.
However, when the loopback netdev goes down all the blackhole nexthops
are flushed. This happens because internally the kernel associates
blackhole nexthops with the loopback netdev.
This behavior is both confusing to those not familiar with kernel
internals and also diverges from the legacy API where blackhole IPv4
routes are not flushed when the loopback netdev goes down:
# ip route add blackhole 198.51.100.0/24
# ip link set dev lo down
# ip route show 198.51.100.0/24
blackhole 198.51.100.0/24
Blackhole IPv6 routes are flushed, but at least user space knows that
they are associated with the loopback netdev:
# ip -6 route show 2001:db8:1::/64
blackhole 2001:db8:1::/64 dev lo metric 1024 pref medium
Fix this by only flushing blackhole nexthops when the loopback netdev is
unregistered.
Fixes: ab84be7e54 ("net: Initial nexthop code")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Donald Sharp <sharpd@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validation of messages for get / del of a next hop is the same as will be
validation of messages for get of a resilient next hop group bucket. The
difference is that policy for resilient next hop group buckets is a
superset of that used for next-hop get.
It is therefore possible to reuse the code that validates the nhmsg fields,
extracts the next-hop ID, and validates that. To that end, extract from
nh_valid_get_del_req() a helper __nh_valid_get_del_req() that does just
that.
Make the nlh argument const so that the function can be called from the
dump context, which only has a const nlh. Propagate the constness to
nh_valid_get_del_req().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to allow different handling for next-hop tree dumper and for
bucket dumper, parameterize the next-hop tree walker with a callback. Add
rtm_dump_nexthop_cb() with just the bits relevant for next-hop tree
dumping.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract from rtm_dump_nexthop() a helper to walk the next hop tree. A
separate function for this will be reusable from the bucket dumper.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dump operations need to keep state from one invocation to another. A
scratch area is dedicated for this purpose in the passed-in argument, cb,
namely via two aliased arrays, struct netlink_callback.args and .ctx.
Dumping of buckets will end up having to iterate over next hops as well,
and it would be nice to be able to reuse the iteration logic with the NH
dumper. The fact that the logic currently relies on fixed index to the
.args array, and the indices would have to be coordinated between the two
dumpers, makes this somewhat awkward.
To make the access patters clearer, introduce a helper struct with a NH
index, and instead of using the .args array directly, use it through this
structure.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests to dump nexthops have many attributes in common with those that
requests to dump buckets of resilient NH groups will have. However, they
have different policies. To allow reuse of this code, extract a
policy-agnostic wrapper out of nh_valid_dump_req(), and convert this
function into a thin wrapper around it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests to dump nexthops have many attributes in common with those that
requests to dump buckets of resilient NH groups will have. In order to make
reuse of this code simpler, convert the code to use a single structure with
filtering configuration instead of passing around the parameters one by
one.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After there are several next-hop group types, initialization and
finalization of notifier type needs to reflect the actual type. Transform
nh_notifier_grp_info_init() and _fini() to make extending them easier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently there are only two types of in-kernel nexthop notification.
The two are distinguished by the 'is_grp' boolean field in 'struct
nh_notifier_info'.
As more notification types are introduced for more next-hop group types, a
boolean is not an easily extensible interface. Instead, convert it to an
enum.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the code that deals with nexthop groups relies on the fact that the
group is of exactly one well-known type. Currently there is only one type,
"mpath", but as more next-hop group types come, it becomes desirable to
have a central place where the setting is validated. Introduce such place
into nexthop_create_group(), such that the check is done before the code
that relies on that invariant is invoked.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The values that a next-hop group needs to keep track of depend on the group
type. Introduce a union to separate fields specific to the mpath groups
from fields specific to other group types.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic for selecting path depends on the next-hop group type. Adapt the
nexthop_select_path() to dispatch according to the group type.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nexthop_free_mpath really should be nexthop_free_group. Rename it.
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This policy is currently only used for creation of new next hops and new
next hop groups. Rename it accordingly and remove the two attributes that
are not valid in that context: NHA_GROUPS and NHA_MASTER.
For consistency with other policies, do not mention policy array size in
the declarator, and replace NHA_MAX for ARRAY_SIZE as appropriate.
Note that with this commit, NHA_MAX and __NHA_MAX are not used anymore.
Leave them in purely as a user API.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function uses the global nexthop policy, but only accepts four
particular attributes. Create a new policy that only includes the four
supported attributes, and use it. Convert the loop to a series of ifs.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function uses the global nexthop policy only to then bounce all
arguments except for NHA_ID. Instead, just create a new policy that
only includes the one allowed attribute.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function nh_check_attr_group() is called to validate nexthop groups.
The intention of that code seems to have been to bounce all attributes
above NHA_GROUP_TYPE except for NHA_FDB. However instead it bounces all
these attributes except when NHA_FDB attribute is present--then it accepts
them.
NHA_FDB validation that takes place before, in rtm_to_nh_config(), already
bounces NHA_OIF, NHA_BLACKHOLE, NHA_ENCAP and NHA_ENCAP_TYPE. Yet further
back, NHA_GROUPS and NHA_MASTER are bounced unconditionally.
But that still leaves NHA_GATEWAY as an attribute that would be accepted in
FDB nexthop groups (with no meaning), so long as it keeps the address
family as unspecified:
# ip nexthop add id 1 fdb via 127.0.0.1
# ip nexthop add id 10 fdb via default group 1
The nexthop code is still relatively new and likely not used very broadly,
and the FDB bits are newer still. Even though there is a reproducer out
there, it relies on an improbable gateway arguments "via default", "via
all" or "via any". Given all this, I believe it is OK to reformulate the
condition to do the right thing and bounce NHA_GATEWAY.
Fixes: 38428d6871 ("nexthop: support for fdb ecmp nexthops")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of error, remove the nexthop group entry from the list to which
it was previously added.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A reference was not taken for the current nexthop entry, so do not try
to put it in the error path.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When registering a new notifier to the nexthop notification chain,
replay all the existing nexthops to the new notifier so that it will
have a complete picture of the available nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This will be used by the next patch which extends the function to replay
all the existing nexthops to the notifier block being registered.
Device drivers will be able to pass extack to the function since it is
passed to them upon reload from devlink.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a single nexthop is deleted, the configuration of all the groups
using the nexthop is effectively modified. In this case, emit a
notification in the nexthop notification chain for each modified group
so that listeners would not need to keep track of which nexthops are
member in which groups.
In the rare cases where the notification fails, emit an error to the
kernel log. This is done by allocating extack on the stack and printing
the error logged by the listener that rejected the notification.
Changes since RFC:
* Allocate extack on the stack
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a single nexthop is replaced, the configuration of all the groups
using the nexthop is effectively modified. In this case, emit a
notification in the nexthop notification chain for each modified group
so that listeners would not need to keep track of which nexthops are
member in which groups.
The notification can only be emitted after the new configuration (i.e.,
'struct nh_info') is pointed at by the old shell (i.e., 'struct
nexthop'). Before that the configuration of the nexthop groups is still
the same as before the replacement.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The notification is emitted after all the validation checks were
performed, but before the new configuration (i.e., 'struct nh_info') is
pointed at by the old shell (i.e., 'struct nexthop'). This prevents the
need to perform rollback in case the notification is vetoed.
The next patch will also emit a replace notification for all the nexthop
groups in which the nexthop is used.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Emit a notification in the nexthop notification chain when an existing
nexthop group is replaced.
The notification is emitted after all the validation checks were
performed, but before the new configuration (i.e., 'struct nh_grp') is
pointed at by the old shell (i.e., 'struct nexthop'). This prevents the
need to perform rollback in case the notification is vetoed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Emit a notification in the nexthop notification chain when a new nexthop
is added (not replaced). The nexthop can either be a new group or a
single nexthop.
The notification is sent after the nexthop is inserted into the
red-black tree, as listeners might need to callback into the nexthop
code with the nexthop ID in order to mark the nexthop as offloaded.
A 'REPLACE' notification is emitted instead of 'ADD' as the distinction
between the two is not important for in-kernel listeners. In case the
listener is not familiar with the encoded nexthop ID, it can simply
treat it as a new one. This is also consistent with the route offload
API.
Changes since RFC:
* Reword commit message
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function that can be called by device drivers to set "offload" or
"trap" indication on nexthops following nexthop notifications.
Changes since RFC:
* s/nexthop_hw_flags_set/nexthop_set_hw_flags/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the sole listener of the nexthop notification chain (the VXLAN
driver) to the new notification info.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare the new notification information so that it could be passed to
listeners in the new patch.
Changes since RFC:
* Add a blank line in __nh_notifier_single_info_init()
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The next patch will add extack to the notification info. This allows
listeners to veto notifications and communicate the reason to user space.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While insertion of 16k nexthops all using the same netdev ('dummy10')
takes less than a second, deletion takes about 130 seconds:
# time -p ip -b nexthop.batch
real 0.29
user 0.01
sys 0.15
# time -p ip link set dev dummy10 down
real 131.03
user 0.06
sys 0.52
This is because of repeated calls to synchronize_rcu() whenever a
nexthop is removed from a nexthop group:
# /usr/share/bcc/tools/offcputime -p `pgrep -nx ip` -K
...
b'finish_task_switch'
b'schedule'
b'schedule_timeout'
b'wait_for_completion'
b'__wait_rcu_gp'
b'synchronize_rcu.part.0'
b'synchronize_rcu'
b'__remove_nexthop'
b'remove_nexthop'
b'nexthop_flush_dev'
b'nh_netdev_event'
b'raw_notifier_call_chain'
b'call_netdevice_notifiers_info'
b'__dev_notify_flags'
b'dev_change_flags'
b'do_setlink'
b'__rtnl_newlink'
b'rtnl_newlink'
b'rtnetlink_rcv_msg'
b'netlink_rcv_skb'
b'rtnetlink_rcv'
b'netlink_unicast'
b'netlink_sendmsg'
b'____sys_sendmsg'
b'___sys_sendmsg'
b'__sys_sendmsg'
b'__x64_sys_sendmsg'
b'do_syscall_64'
b'entry_SYSCALL_64_after_hwframe'
- ip (277)
126554955
Since nexthops are always deleted under RTNL, synchronize_net() can be
used instead. It will call synchronize_rcu_expedited() which only blocks
for several microseconds as opposed to multiple milliseconds like
synchronize_rcu().
With this patch deletion of 16k nexthops takes less than a second:
# time -p ip link set dev dummy10 down
real 0.12
user 0.00
sys 0.04
Tested with fib_nexthops.sh which includes torture tests that prompted
the initial change:
# ./fib_nexthops.sh
...
Tests passed: 134
Tests failed: 0
Fixes: 90f33bffa3 ("nexthops: don't modify published nexthop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20201016172914.643282-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the in-kernel delete notification is emitted from the error
path of nexthop_add() and replace_nexthop(), which can be confusing to
in-kernel listeners as they are not familiar with the nexthop.
Instead, only emit the notification when the nexthop is actually
deleted. The following sub-cases are covered:
1. User space deletes the nexthop
2. The nexthop is deleted by the kernel due to a netdev event (e.g.,
nexthop device going down)
3. A group is deleted because its last nexthop is being deleted
4. The network namespace of the nexthop device is deleted
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the only listener of the nexthop notification chain is the
VXLAN driver. Subsequent patches will add more listeners (e.g., device
drivers such as netdevsim) that need to be able to block when processing
notifications.
Therefore, convert the notification chain to a blocking one. This is
safe as notifications are always emitted from process context.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each nexthop group contains an indication if it has IPv4 nexthops
('has_v4'). Its purpose is to prevent IPv6 routes from using groups with
IPv4 nexthops.
However, the indication is not updated when a nexthop is replaced. This
results in the kernel wrongly rejecting IPv6 routes from pointing to
groups that only contain IPv6 nexthops. Example:
# ip nexthop replace id 1 via 192.0.2.2 dev dummy10
# ip nexthop replace id 10 group 1
# ip nexthop replace id 1 via 2001:db8:1::2 dev dummy10
# ip route replace 2001:db8:10::/64 nhid 10
Error: IPv6 routes can not use an IPv4 nexthop.
Solve this by iterating over all the nexthop groups that the replaced
nexthop is a member of and potentially update their IPv4 indication
according to the new set of member nexthops.
Avoid wasting cycles by only performing the update in case an IPv4
nexthop is replaced by an IPv6 nexthop.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each nexthop group contains an indication if it has IPv4 nexthops
('has_v4'). Its purpose is to prevent IPv6 routes from using groups with
IPv4 nexthops.
However, the indication is not updated when a nexthop is removed. This
results in the kernel wrongly rejecting IPv6 routes from pointing to
groups that only contain IPv6 nexthops. Example:
# ip nexthop replace id 1 via 192.0.2.2 dev dummy10
# ip nexthop replace id 2 via 2001:db8:1::2 dev dummy10
# ip nexthop replace id 10 group 1/2
# ip nexthop del id 1
# ip route replace 2001:db8:10::/64 nhid 10
Error: IPv6 routes can not use an IPv4 nexthop.
Solve this by updating the indication according to the new set of
member nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer is not RCU protected, so remove the unnecessary
rtnl_dereference(). This suppresses the following warning:
net/ipv4/nexthop.c:1101:24: error: incompatible types in comparison expression (different address spaces):
net/ipv4/nexthop.c:1101:24: struct rb_node [noderef] __rcu *
net/ipv4/nexthop.c:1101:24: struct rb_node *
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code correctly uses nla_get_be32() to get the payload of the
attribute, but incorrectly uses nla_put_u32() to add the attribute to
the payload. This results in the following warning:
net/ipv4/nexthop.c:279:59: warning: incorrect type in argument 3 (different base types)
net/ipv4/nexthop.c:279:59: expected unsigned int [usertype] value
net/ipv4/nexthop.c:279:59: got restricted __be32 [usertype] ipv4
Suppress the warning by using nla_put_be32().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct looks as follows:
struct nh_group {
struct nh_group *spare; /* spare group for removals */
u16 num_nh;
bool mpath;
bool fdb_nh;
bool has_v4;
struct nh_grp_entry nh_entries[];
};
But its offset within 'struct nexthop' is also taken into account to
determine the allocation size.
Instead, use struct_size() to allocate only the required number of
bytes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb nexthops are marked with a flag. For standalone nexthops, a flag was
added to the nh_info struct. For groups that flag was added to struct
nexthop when it should have been added to the group information. Fix
by removing the flag from the nexthop struct and adding a flag to nh_group
that mirrors nh_info and is really only a caching of the individual types.
Add a helper, nexthop_is_fdb, for use by the vxlan code and fixup the
internal code to use the flag from either nh_info or nh_group.
v2
- propagate fdb_nh in remove_nh_grp_entry
Fixes: 38428d6871 ("nexthop: support for fdb ecmp nexthops")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allocating the spare nexthop group it should be tested for kzalloc()
returning NULL, instead the already used nexthop group (which cannot be
NULL at this point) had been tested so far.
Additionally, if kzalloc() fails, return ERR_PTR(-ENOMEM) instead of NULL.
Coverity-id: 1463885
Reported-by: Coverity <scan-admin@coverity.com>
Signed-off-by: Patrick Eigensatz <patrickeigensatz@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
net/ipv4/nexthop.c:841:30: warning: implicit conversion from enumeration
type 'enum nexthop_event_type' to different enumeration type 'enum
fib_event_type' [-Wenum-conversion]
call_nexthop_notifiers(net, NEXTHOP_EVENT_DEL, nh);
~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~
1 warning generated.
Use the right type for event_type so that clang does not warn.
Fixes: 8590ceedb7 ("nexthop: add support for notifiers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1038
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must avoid modifying published nexthop groups while they might be
in use, otherwise we might see NULL ptr dereferences. In order to do
that we allocate 2 nexthoup group structures upon nexthop creation
and swap between them when we have to delete an entry. The reason is
that we can't fail nexthop group removal, so we can't handle allocation
failure thus we move the extra allocation on creation where we can
safely fail and return ENOMEM.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move nh_grp dereference and check for removing nexthop group due to
all members gone into remove_nh_grp_entry.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds nexthop add/del notifiers. To be used by
vxlan driver in a later patch. Could possibly be used by
switchdev drivers in the future.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ecmp nexthops and nexthop groups
for mac fdb entries. In subsequent patches this is used
by the vxlan driver fdb entries. The use case is
E-VPN multihoming [1,2,3] which requires bridged vxlan traffic
to be load balanced to remote switches (vteps) belonging to
the same multi-homed ethernet segment (This is analogous to
a multi-homed LAG but over vxlan).
Changes include new nexthop flag NHA_FDB for nexthops
referenced by fdb entries. These nexthops only have ip.
This patch includes appropriate checks to avoid routes
referencing such nexthops.
example:
$ip nexthop add id 12 via 172.16.1.2 fdb
$ip nexthop add id 13 via 172.16.1.3 fdb
$ip nexthop add id 102 group 12/13 fdb
$bridge fdb add 02:02:00:00:00:13 dev vxlan1000 nhid 101 self
[1] E-VPN https://tools.ietf.org/html/rfc7432
[2] E-VPN VxLAN: https://tools.ietf.org/html/rfc8365
[3] LPC talk with mention of nexthop groups for L2 ecmp
http://vger.kernel.org/lpc_net2018_talks/scaling_bridge_fdb_database_slidesV3.pdf
v4 - fixed uninitialized variable reported by kernel test robot
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes data remnant seen when we fail to reserve space for a
nexthop group during a larger dump.
If we fail the reservation, we goto nla_put_failure and
cancel the message.
Reproduce with the following iproute2 commands:
=====================
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip link add dummy20 type dummy
ip link add dummy21 type dummy
ip link add dummy22 type dummy
ip link add dummy23 type dummy
ip link add dummy24 type dummy
ip link add dummy25 type dummy
ip link add dummy26 type dummy
ip link add dummy27 type dummy
ip link add dummy28 type dummy
ip link add dummy29 type dummy
ip link add dummy30 type dummy
ip link add dummy31 type dummy
ip link add dummy32 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip link set dummy3 up
ip link set dummy4 up
ip link set dummy5 up
ip link set dummy6 up
ip link set dummy7 up
ip link set dummy8 up
ip link set dummy9 up
ip link set dummy10 up
ip link set dummy11 up
ip link set dummy12 up
ip link set dummy13 up
ip link set dummy14 up
ip link set dummy15 up
ip link set dummy16 up
ip link set dummy17 up
ip link set dummy18 up
ip link set dummy19 up
ip link set dummy20 up
ip link set dummy21 up
ip link set dummy22 up
ip link set dummy23 up
ip link set dummy24 up
ip link set dummy25 up
ip link set dummy26 up
ip link set dummy27 up
ip link set dummy28 up
ip link set dummy29 up
ip link set dummy30 up
ip link set dummy31 up
ip link set dummy32 up
ip link set dummy33 up
ip link set dummy34 up
ip link set vrf-red up
ip link set vrf-blue up
ip link set dummyVRFred up
ip link set dummyVRFblue up
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip ro add 1.1.1.20/32 dev dummy20
ip ro add 1.1.1.21/32 dev dummy21
ip ro add 1.1.1.22/32 dev dummy22
ip ro add 1.1.1.23/32 dev dummy23
ip ro add 1.1.1.24/32 dev dummy24
ip ro add 1.1.1.25/32 dev dummy25
ip ro add 1.1.1.26/32 dev dummy26
ip ro add 1.1.1.27/32 dev dummy27
ip ro add 1.1.1.28/32 dev dummy28
ip ro add 1.1.1.29/32 dev dummy29
ip ro add 1.1.1.30/32 dev dummy30
ip ro add 1.1.1.31/32 dev dummy31
ip ro add 1.1.1.32/32 dev dummy32
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 20 via 1.1.1.20 dev dummy20
ip next add id 21 via 1.1.1.21 dev dummy21
ip next add id 22 via 1.1.1.22 dev dummy22
ip next add id 23 via 1.1.1.23 dev dummy23
ip next add id 24 via 1.1.1.24 dev dummy24
ip next add id 25 via 1.1.1.25 dev dummy25
ip next add id 26 via 1.1.1.26 dev dummy26
ip next add id 27 via 1.1.1.27 dev dummy27
ip next add id 28 via 1.1.1.28 dev dummy28
ip next add id 29 via 1.1.1.29 dev dummy29
ip next add id 30 via 1.1.1.30 dev dummy30
ip next add id 31 via 1.1.1.31 dev dummy31
ip next add id 32 via 1.1.1.32 dev dummy32
i=100
while [ $i -le 200 ]
do
ip next add id $i group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
echo $i
((i++))
done
ip next add id 999 group 1/2/3/4/5/6
ip next ls
========================
Fixes: ab84be7e54 ("net: Initial nexthop code")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For nexthop groups, attributes after NHA_GROUP_TYPE are invalid, but
nh_check_attr_group starts checking at NHA_GROUP. The group type defaults
to multipath and the NHA_GROUP_TYPE is currently optional so this has
slipped through so far. Fix the attribute checking to handle support of
new group types.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: ASSOGBA Emery <assogba.emery@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the various uses of fallthrough comments to fallthrough;
Done via script
Link: https://lore.kernel.org/lkml/b56602fcf79f849e733e7b521bb0e17895d390fa.1582230379.git.joe@perches.com/
And by hand:
net/ipv6/ip6_fib.c has a fallthrough comment outside of an #ifdef block
that causes gcc to emit a warning if converted in-place.
So move the new fallthrough; inside the containing #ifdef/#endif too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the size of struct nhmsg size when calculating
how much of a payload to allocate in a new netlink nexthop
notification message.
Without this, we will fail to fill the skbuff at certain nexthop
group sizes.
You can reproduce the failure with the following iproute2 commands:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 1111 group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
ip next del id 1111
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ct_policy and mpls_policy are parsed with nla_parse_nested(), which
does NL_VALIDATE_STRICT validation, strict_start_type is not needed
to set as it is actually trying to make some attributes parsed with
NL_VALIDATE_STRICT.
This patch is to remove it, and do the same on rtm_nh_policy which
is parsed by nlmsg_parse().
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused Value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for atomically upating a nexthop config.
When updating a nexthop, walk the lists of associated fib entries and
verify the new config is valid. Replace is done by swapping nh_info
for single nexthops - new config is applied to old nexthop struct, and
old config is moved to new nexthop struct. For nexthop groups the same
applies but for nh_group. In addition for groups the nh_parent reference
needs to be updated. The old config is released by calling __remove_nexthop
on the 'new' nexthop which now has the old config. This is done to avoid
messing around with the list_heads that track which fib entries are
using the nexthop.
After the swap of config data, bump the sequence counters for FIB entries
to invalidate any dst entries and send notifications to userspace. The
notifications include the new nexthop spec as well as any fib entries
using the updated nexthop struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 has traditionally had a single fib6_nh per fib6_info. With
nexthops we can have multiple fib6_nh associated with a fib6_info.
Add a nexthop helper to invoke a callback for each fib6_nh in a
'struct nexthop'. If the callback returns non-0, the loop is
stopped and the return value passed to the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct nexthop and nh_list list_head to fib6_info. nh_list is the
fib6_info side of the nexthop <-> fib_info relationship. Since a fib6_info
referencing a nexthop object can not have 'sibling' entries (the old way
of doing multipath routes), the nh_list is a union with fib6_siblings.
Add f6i_list list_head to 'struct nexthop' to track fib6_info entries
using a nexthop instance. Update __remove_nexthop_fib to walk f6_list
and delete fib entries using the nexthop.
Add a few nexthop helpers for use when a nexthop is added to fib6_info:
- nexthop_fib6_nh - return first fib6_nh in a nexthop object
- fib6_info_nh_dev moved to nexthop.h and updated to use nexthop_fib6_nh
if the fib6_info references a nexthop object
- nexthop_path_fib6_result - similar to ipv4, select a path within a
multipath nexthop object. If the nexthop is a blackhole, set
fib6_result type to RTN_BLACKHOLE, and set the REJECT flag
Update the fib6_info references to check for nh and take a different path
as needed:
- rt6_qualify_for_ecmp - if a fib entry uses a nexthop object it can NOT
be coalesced with other fib entries into a multipath route
- rt6_duplicate_nexthop - use nexthop_cmp if either fib6_info references
a nexthop
- addrconf (host routes), RA's and info entries (anything configured via
ndisc) does not use nexthop objects
- fib6_info_destroy_rcu - put reference to nexthop object
- fib6_purge_rt - drop fib6_info from f6i_list
- fib6_select_path - update to use the new nexthop_path_fib6_result when
fib entry uses a nexthop object
- rt6_device_match - update to catch use of nexthop object as a blackhole
and set fib6_type and flags.
- ip6_route_info_create - don't add space for fib6_nh if fib entry is
going to reference a nexthop object, take a reference to nexthop object,
disallow use of source routing
- rt6_nlmsg_size - add space for RTA_NH_ID
- add rt6_fill_node_nexthop to add nexthop data on a dump
As with ipv4, most of the changes push existing code into the else branch
of whether the fib entry uses a nexthop object.
Update the nexthop code to walk f6i_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'struct nexthop' and nh_list list_head to fib_info. nh_list is the
fib_info side of the nexthop <-> fib_info relationship.
Add fi_list list_head to 'struct nexthop' to track fib_info entries
using a nexthop instance. Add __remove_nexthop_fib and add it to
__remove_nexthop to walk the new list_head and mark those fib entries
as dead when the nexthop is deleted.
Add a few nexthop helpers for use when a nexthop is added to fib_info:
- nexthop_cmp to determine if 2 nexthops are the same
- nexthop_path_fib_result to select a path for a multipath
'struct nexthop'
- nexthop_fib_nhc to select a specific fib_nh_common within a
multipath 'struct nexthop'
Update existing fib_info_nhc to use nexthop_fib_nhc if a fib_info uses
a 'struct nexthop', and mark fib_info_nh as only used for the non-nexthop
case.
Update the fib_info functions to check for fi->nh and take a different
path as needed:
- free_fib_info_rcu - put the nexthop object reference
- fib_release_info - remove the fib_info from the nexthop's fi_list
- nh_comp - use nexthop_cmp when either fib_info references a nexthop
object
- fib_info_hashfn - use the nexthop id for the hashing vs the oif of
each fib_nh in a fib_info
- fib_nlmsg_size - add space for the RTA_NH_ID attribute
- fib_create_info - verify nexthop reference can be taken, verify
nexthop spec is valid for fib entry, and add fib_info to fi_list for
a nexthop
- fib_select_multipath - use the new nexthop_path_fib_result to select a
path when nexthop objects are used
- fib_table_lookup - if the 'struct nexthop' is a blackhole nexthop, treat
it the same as a fib entry using 'blackhole'
The bulk of the changes are in fib_semantics.c and most of that is
moving the existing change_nexthops into an else branch.
Update the nexthop code to walk fi_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert more IPv4 code to use fib_nh_common over fib_nh to enable routes
to use a fib6_nh based nexthop. In the end, only code not using a
nexthop object in a fib_info should directly access fib_nh in a fib_info
without checking the famiy and going through fib_nh_common. Those
functions will be marked when it is not directly evident.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is initialized with a value that is never read
and err is reassigned a few statements later. This initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the creation of nexthop groups which reference other nexthop
objects to create multipath routes:
+--------------+
+------------+ +--------------+ |
| nh nh_grp --->| nh_grp_entry |-+
+------------+ +---------|----+
^ | | +------------+
+----------------+ +--->| nh, weight |
nh_parent +------------+
A group entry points to a nexthop with a weight for that hop within the
group. The nexthop has a list_head, grp_list, for tracking which groups
it is a member of and the group entry has a reference back to the parent.
The grp_list is used when a nexthop is deleted - to efficiently remove
it from groups using it.
If a nexthop group spec is given, no other attributes can be set. Each
nexthop id in a group spec must already exist.
Similar to single nexthops, the specification of a nexthop group can be
updated so that data is managed with rcu locking.
Add path selection function to account for multiple paths and add
ipv{4,6}_good_nh helpers to know that if a neighbor entry exists it is
in a good state.
Update NETDEV event handling to rebalance multipath nexthop groups if
a nexthop is deleted due to a link event (down or unregister).
When a nexthop is removed any groups using it are updated. Groups using a
nexthop a tracked via a grp_list.
Nexthop dumps can be limited to groups only by adding NHA_GROUPS to the
request.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for NHA_ENCAP and NHA_ENCAP_TYPE. Leverages the existing code
for lwtunnel within fib_nh_common, so the only change needed is handling
the attributes in the nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle IPv6 gateway in a nexthop spec. If nh_family is set to AF_INET6,
NHA_GATEWAY is expected to be an IPv6 address. Add ipv6 option to gw in
nh_config to hold the address, add fib6_nh to nh_info to leverage the
ipv6 initialization and cleanup code. Update nh_fill_node to dump the v6
address.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv4 nexthops. If nh_family is set to AF_INET, then
NHA_GATEWAY is expected to be an IPv4 address.
Register for netdev events to be notified of admin up/down changes as
well as deletes. A hash table is used to track nexthop per devices to
quickly convert device events to the affected nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Barebones start point for nexthops. Implementation for RTM commands,
notifications, management of rbtree for holding nexthops by id, and
kernel side data structures for nexthops and nexthop config.
Nexthops are maintained in an rbtree sorted by id. Similar to routes,
nexthops are configured per namespace using netns_nexthop struct added
to struct net.
Nexthop notifications are sent when a nexthop is added or deleted,
but NOT if the delete is due to a device event or network namespace
teardown (which also involves device events). Applications are
expected to use the device down event to flush nexthops and any
routes used by the nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
