The base iomux offsets for each GPIO pin line are accumulatively
calculated based off iomux width flag in rockchip_pinctrl_get_soc_data.
If the iomux width flag is one of IOMUX_WIDTH_4BIT, IOMUX_WIDTH_3BIT or
IOMUX_WIDTH_2BIT, the base offset for next pin line would increase by 8
bytes, otherwise it would increase by 4 bytes.
Despite most of GPIO2-B iomux have 2-bit data width, which can be fit
into 4 bytes space with write mask, it actually take 8 bytes width for
whole GPIO2-B line.
Commit e8448a6c81 ("pinctrl: rockchip: fix pinmux bits for RK3328
GPIO2-B pins") wrongly set iomux width flag to 0, causing all base
iomux offset for line after GPIO2-B to be calculated wrong. Fix the
iomux width flag to IOMUX_WIDTH_2BIT so the offset after GPIO2-B is
correctly increased by 8, matching the actual width of GPIO2-B iomux.
Fixes: e8448a6c81 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
Cc: stable@vger.kernel.org
Reported-by: Richard Kojedzinszky <richard@kojedz.in>
Closes: https://lore.kernel.org/linux-rockchip/4f29b743202397d60edfb3c725537415@kojedz.in/
Tested-by: Richard Kojedzinszky <richard@kojedz.in>
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Trevor Woerner <twoerner@gmail.com>
Link: https://lore.kernel.org/20240709105428.1176375-1-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://lore.kernel.org/20240814030155.3876069-1-liaochen4@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If pinctrl_enable() fails in pcs_probe(), it should return the error code.
Fixes: 8f773bfbdd ("pinctrl: single: fix possible memory leak when pinctrl_enable() fails")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/20240819024625.154441-1-yangyingliang@huaweicloud.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace SET_LATE_SYSTEM_SLEEP_PM_OPS() with its modern
LATE_SYSTEM_SLEEP_PM_OPS() alternative.
The combined usage of pm_sleep_ptr() and LATE_SYSTEM_SLEEP_PM_OPS() allows
the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/20240808162750.244092-1-festevam@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the erroneus 0x100000 offset to prevent the boards from crashing
on pin state setting, as well as for the intended state changes to take
effect.
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20240809-topic-h_sdc-v1-1-bb421532c531@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Despite its name, commit fed74d7527 ("pinctrl: mediatek: common-v2:
Fix bias-disable for PULL_PU_PD_RSEL_TYPE") actually broke bias-disable
for PULL_PU_PD_RSEL_TYPE.
mtk_pinconf_bias_set_combo() tries every bias method supported by the
pin until one succeeds. For PULL_PU_PD_RSEL_TYPE pins, before the
breaking commit, mtk_pinconf_bias_set_rsel() would be called first to
try and set the RSEL value (as well as PU and PD), and if that failed,
the only other valid option was that bias-disable was specified, which
would then be handled by calling mtk_pinconf_bias_set_pu_pd() and
disabling both PU and PD.
The breaking commit misunderstood this logic and added an early "return
0" in mtk_pinconf_bias_set_rsel(). The result was that in the
bias-disable case, the bias was left unchanged, since by returning
success, mtk_pinconf_bias_set_combo() no longer tried calling
mtk_pinconf_bias_set_pu_pd() to disable the bias.
Since the logic for configuring bias-disable on PULL_PU_PD_RSEL_TYPE
pins required mtk_pinconf_bias_set_rsel() to fail first, in that case,
an error was printed to the log, eg:
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 0 Ohm for pin = 29 (GPIO29)
This is what the breaking commit actually got rid of, and likely part of
the reason why that commit was thought to be fixing functionality, while
in reality it was breaking it.
Instead of simply reverting that commit, restore the functionality but
in a way that avoids the error from being printed and makes the code
less confusing:
* Return 0 explicitly if a bias method was successful
* Introduce an extra function mtk_pinconf_bias_set_pu_pd_rsel() that
calls both mtk_pinconf_bias_set_rsel() (only if needed) and
mtk_pinconf_bias_set_pu_pd()
* And analogously for the corresponding getters
Fixes: fed74d7527 ("pinctrl: mediatek: common-v2: Fix bias-disable for PULL_PU_PD_RSEL_TYPE")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/20240808-mtk-rsel-bias-disable-fix-v1-1-1b4e85bf596c@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinmux_generic_get_function() can return NULL and the pointer 'function'
was dereferenced without checking against NULL. Add checking of pointer
'function' in pcs_get_function().
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 571aec4df5 ("pinctrl: single: Use generic pinmux helpers for managing functions")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://lore.kernel.org/20240808041355.2766009-1-make24@iscas.ac.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_property_read_bool() to read boolean properties rather than
of_find_property(). This is part of a larger effort to remove callers
of of_find_property() and similar functions. of_find_property() leaks
the DT struct property and data pointers which is a problem for
dynamically allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/20240731191312.1710417-23-robh@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-at91 currently does not support the gpio-groups devicetree
property and has no pin-range.
Because of this at91 gpios stopped working since patch
commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
This was discussed in the patches
commit fc328a7d1f ("gpio: Revert regression in sysfs-gpio (gpiolib.c)")
commit 56e337f2cf ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
As a workaround manually set pin-range via gpiochip_add_pin_range() until
a) pinctrl-at91 is reworked to support devicetree gpio-groups
b) another solution as mentioned in
commit 56e337f2cf ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
is found
Signed-off-by: Thomas Blocher <thomas.blocher@ek-dev.de>
Link: https://lore.kernel.org/5b992862-355d-f0de-cd3d-ff99e67a4ff1@ek-dev.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let kmemdup_array() take care of multiplication and possible overflow.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240822061438.14617-1-shenlichuan@vivo.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Let the kmemdup_array() take care about multiplication
and possible overflows.
Using kmemdup_array() is more appropriate and makes the code
easier to audit.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://lore.kernel.org/r/20240823114441.50648-1-shenlichuan@vivo.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Gpiolib framework has the implementation of setting up the
PUD configuration for GPIO pins but there is no driver support.
Add support to handle the PUD configuration request from the
userspace in samsung pinctrl driver.
Signed-off-by: Vishnu Reddy <vishnu.reddy@samsung.com>
Link: https://lore.kernel.org/r/20240729153631.24536-1-vishnu.reddy@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
This includes a new ACPI ID that is added to the Intel Meteor Lake
driver to support recent Intel Arrow Lake hardware.
-----BEGIN PGP SIGNATURE-----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=Mbpf
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v6.11-1
This includes a new ACPI ID that is added to the Intel Meteor Lake
driver to support recent Intel Arrow Lake hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The previous pinconf settings(made by the bootloader) need to be
overwritten when configuring the pinctrl of a driver during the boot
process.
Configuring the bias of a GPIO at runtime (e.g. pull-up) needs to
preserve the other settings unaltered.
This patch introduces changes to differentiate between the two cases.
Signed-off-by: Radu Pirea <radu-nicolae.pirea@nxp.com>
Signed-off-by: Florin Buica <florin.buica@nxp.com>
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com>
Link: https://lore.kernel.org/20240723131832.1171036-4-andrei.stefanescu@oss.nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously, it was possible to only configure the open-drain for a pin.
However, after a pin got configured with open-drain, there wasn't any
way to disable it. Add the push-pull configuration in order to reverse
the open-drain configuration.
Signed-off-by: Florin Buica <florin.buica@nxp.com>
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com>
Link: https://lore.kernel.org/20240723131832.1171036-3-andrei.stefanescu@oss.nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IBE (input buffer enable) should be enabled for a GPIO. Reading the
value will return the one from the input register, writing the value
will return the one from the output register.
This offers the flexibility to check if the value intended to be set
matches the actual physical one.
Signed-off-by: Florin Buica <florin.buica@nxp.com>
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com>
Link: https://lore.kernel.org/20240723131832.1171036-2-andrei.stefanescu@oss.nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for GPIO pins GPI35 and GPI36 on the Nuvoton
NPCM8xx BMC SoC.
The pins are configured for only for input.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/20240716194008.3502068-5-tmaimon77@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clear polarity before setting both edges to ensure that the polarity is
in the same state before configuring events for both edges
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/20240716194008.3502068-4-tmaimon77@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove non-existent smb4den abd lpcclk pins, groups and functions on
the Nuvoton NPCM8XX BMC SoC.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/20240716194008.3502068-3-tmaimon77@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current map seems to be out of sync (and includes a duplicate entry
for GPIO193..).
Replace it with the map present in shipping devices' ACPI tables.
This new one seems more complete, as it e.g. contains GPIO145 (PCIE6a
WAKE#)
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Link: https://lore.kernel.org/20240711-topic-x1e_pdc_tlmm-v1-1-e278b249d793@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'struct ti_iodelay_reg_data' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
17259 1788 16 19063 4a77 drivers/pinctrl/ti/pinctrl-ti-iodelay.o
After:
=====
text data bss dec hex filename
17355 1692 16 19063 4a77 drivers/pinctrl/ti/pinctrl-ti-iodelay.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/40d6e67ab4e73d2cbe7ca0060ac27afc894fc415.1720556038.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the probe, if an error occurs after the ti_iodelay_pinconf_init_dev()
call, it is likely that ti_iodelay_pinconf_deinit_dev() should be called,
as already done in the remove function.
Also in ti_iodelay_pinconf_init_dev(), if an error occurs after the first
regmap_update_bits() call, it is also likely that the deinit() function
should be called.
The easier way to fix it is to add a devm_add_action_or_reset() at the
rigtht place to have ti_iodelay_pinconf_deinit_dev() called when needed.
Doing so, the .remove() function can be removed, and the associated
platform_set_drvdata() call in the probe as well.
Fixes: 003910ebc8 ("pinctrl: Introduce TI IOdelay configuration driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/0220fa5b925bd08e361be8206a5438f6229deaac.1720556038.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
`dra7_iodelay_regmap_config` is not modified and can be declared as
const to move its data to a read-only section.
The pointer used to reference that struct has been made const
accordingly.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/20240704-pinctrl-const-regmap_config-v1-1-9d5570f0b9f3@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_property_present() to test for property presence rather than
of_find_property(). This is part of a larger effort to remove callers
of of_find_property() and similar functions. of_find_property() leaks
the DT struct property and data pointers which is a problem for
dynamically allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240731191312.1710417-16-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add the Mobileye EyeQ5 pin controller driver. It belongs to a syscon
region called OLB and gets spawned as auxiliary device to the platform
driver for clock.
Existing pins and their function live statically in the driver code
rather than in the devicetree, see compatible match data.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/20240730-mbly-pinctrl-v2-2-d470f64e0395@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the rzg2l_pinctrl_pinconf_get() function to return -EINVAL for
PIN_CONFIG_OUTPUT_ENABLE config if the pin doesn't support the PIN_CFG_OEN
configuration.
-EINVAL is a valid error when dumping the pin configurations. Returning
-EOPNOTSUPP for a pin that does not support PIN_CFG_OEN resulted in the
message 'ERROR READING CONFIG SETTING 16' being printed during dumping
pinconf-pins.
For consistency do similar change in rzg2l_pinctrl_pinconf_set() for
PIN_CONFIG_OUTPUT_ENABLE config.
Fixes: a9024a323a ("pinctrl: renesas: rzg2l: Clean up and refactor OEN read/write functions")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240723164744.505233-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Intel Arrow Lake-H/U has the same GPIO hardware than Meteor Lake-P but
the ACPI ID is different. Add this new ACPI ID to the list of supported
devices.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more info
on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core to using
a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs from actual
hardware and driving tests of the in-kernel GPIO API from user-space over
debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first glance"
debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested as irqs
via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to errno
vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with regards to
reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop tempting
people to use it
- document the preference for using pread() for reading edge events in the
sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to specify
a number of callbacks callers can use to be notified about irqs being
requested and released
-----BEGIN PGP SIGNATURE-----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=kK88
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"The majority of added lines are two new modules: the GPIO virtual
consumer module that improves our ability to add automated tests for
the kernel API and the "sloppy" logic analyzer module that uses the
GPIO API to implement a coarse-grained debugging tool for useful for
remote development.
Other than that we have the usual assortment of various driver
extensions, improvements to the core GPIO code, DT-bindings and other
documentation updates as well as an extension to the interrupt
simulator:
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more
info on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot
fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core
to using a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs
from actual hardware and driving tests of the in-kernel GPIO API
from user-space over debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first
glance" debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested
as irqs via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to
errno vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and
gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with
regards to reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop
tempting people to use it
- document the preference for using pread() for reading edge events
in the sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to
specify a number of callbacks callers can use to be notified about
irqs being requested and released"
* tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (41 commits)
gpio: mc33880: Convert comma to semicolon
gpio: virtuser: actually use the "trimmed" local variable
dt-bindings: gpio: convert Atmel GPIO to json-schema
gpio: virtuser: new virtual testing driver for the GPIO API
dt-bindings: gpio: vf610: Allow gpio-line-names to be set
gpio: sim: lock GPIOs as interrupts when they are requested
genirq/irq_sim: add an extended irq_sim initializer
dt-bindings: gpio: fsl,qoriq-gpio: Add compatible string fsl,ls1046a-gpio
gpiolib: unexport gpiochip_get_desc()
gpio: add sloppy logic analyzer using polling
Documentation: gpio: Reconfiguration with unset direction (uAPI v2)
Documentation: gpio: Reconfiguration with unset direction (uAPI v1)
dt-bindings: gpio: fsl,qoriq-gpio: add common property gpio-line-names
gpio: ath79: convert to dynamic GPIO base allocation
pinctrl: da9062: replace gpiochip_get_desc() with gpio_device_get_desc()
gpiolib: put gpio_suffixes in a single compilation unit
Documentation: gpio: Clarify effect of active low flag on line edges
Documentation: gpio: Clarify effect of active low flag on line values
gpiolib: Remove data-less gpiochip_add() function
gpio: sim: use devm_mutex_init()
...
- Support output enable on RZ/G2L.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZoe3qwAKCRCKwlD9ZEnx
cPViAP9qh934pSOC8dw4wpmrPkp2PW6NtdUqrZ7xE6axHuwIwgEAgr7WoYm+hMKc
iS73PYEL4Ord1svI5+ikCkK6dpdjqAI=
=gqek
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v6.11-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v6.11 (take three)
- Support output enable on RZ/G2L.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is by default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240625200316.4282-4-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The variable naming in the various OEN functions has been confusing. We
were passing the _pin & bit variables from rzg2l_pinctrl_pinconf_get()
and rzg2l_pinctrl_pinconf_set() as the offset & pin argument to the
oen_read() and oen_write() functions. This doesn't make sense, the first
of these isn't actually an offset and the second is not needed for
RZ/V2H but leads to confusion with the bit variable used within these
functions.
To tidy this up, instead pass the _pin variable directly to the
oen_read() and oen_write() functions with consistent naming. Then
rzg3s_read_oen() and rzg3s_write_oen() can use macros to get the port
and pin numbers it needs.
Instead of passing the pin capabilities into oen_read() and oen_write(),
check that the pin supports OEN before calling these functions.
Also, merge rzg3s_oen_is_supported() into rzg3s_pin_to_oen_bit() to give
a single translation function which returns an error if the pin doesn't
support OEN. While we're here, remove an unnecessary branch and clarify
the variable naming. Lastly, check that we are not dealing with a
dedicated pin before calling RZG2L_PIN_ID_TO_{PORT,PIN}().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240625200316.4282-3-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We currently support OEN read/write for the RZ/G3S SoC but not the
RZ/G2L SoC family (consisting of RZ/G2L, RZ/G2LC, RZ/G2UL, RZ/V2L &
RZ/Five). The appropriate functions are renamed to clarify this and to
match the callback names.
We should also only set the oen_read and oen_write function pointers for
the devices which support these operations. This requires us to check
that these function pointers are valid before calling them.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240625200316.4282-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use scope based of_node_put() cleanup to simplify code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/20240627131721.678727-4-peng.fan@oss.nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use scope based of_node_put() cleanup to simplify code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/20240627131721.678727-3-peng.fan@oss.nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use scope based of_node_put() cleanup to simplify code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/20240627131721.678727-2-peng.fan@oss.nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the previous review cycle the regmap cache update code was
questioned since it seems and odd way of using regmap_update_bits().
Thus update the regmap cache modification code to better explain
what it does and why it's done. This is no functional change, but
it's improving code maintainability.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/20240626084525.787298-2-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pins named both TCLK3
and TCLK4. To differentiate, the pin control driver uses "TCLK[34]" and
"TCLK[34]_X". In addition, there are alternate pins without suffix, and
with an "_A" or "_B" suffix.
Increase uniformity by adopting R-Car V4M naming:
- Rename "TCLK2_B" to "TCLK2_C",
- Rename "TCLK[12]_A" to "TCLK[12]_B",
- Rename "TCLK[12]" to "TCLK[12]_A",
- Rename "TCLK[34]_A" to "TCLK[34]_C",
- Rename "TCLK[34]_X" to "TCLK[34]_A",
- Rename "TCLK[34]" to "TCLK[34]_B".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 0df46188a5 ("pinctrl: renesas: r8a779g0: Add missing TCLKx_A/TCLKx_B/TCLKx_X")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/2845ff1f8fe1fd8d23d2f307ad5e8eb8243da608.1717754960.git.geert+renesas@glider.be
The suffixes of the IRQ identifiers for external interrupts 0-3
are inconsistent:
- "IRQ0" and "IRQ0_A",
- "IRQ1" and "IRQ1_A",
- "IRQ2" and "IRQ2_A",
- "IRQ3" and "IRQ3_B".
The suffixes for external interrupts 4 and 5 do follow conventional
naming:
- "IRQ4A" and IRQ4_B",
- "IRQ5".
Fix this by adopting R-Car V4M naming:
- Rename "IRQ[0-2]_A" to "IRQ[0-2]_B",
- Rename "IRQ[0-3]" to "IRQ[0-3]_A".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 1b23d8a478 ("pinctrl: renesas: r8a779g0: Add missing IRQx_A/IRQx_B")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/8ce9baf0a0f9346544a3ac801fd962c7c12fd247.1717754960.git.geert+renesas@glider.be
(H)SCIF instance 3 has two alternate pin groups: "hscif3" and
"hscif3_a", resp. "scif3" and "scif3_a", but the actual meanings of the
pins within the groups do not match.
Increase uniformity by adopting R-Car V4M naming:
- Rename "hscif3_a" to "hscif3_b",
- Rename "hscif3" to "hscif3_a",
- Rename "scif3" to "scif3_b".
While at it, remove unneeded separators.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: 213b713255 ("pinctrl: renesas: r8a779g0: Add missing HSCIF3_A")
Fixes: 49e4697656 ("pinctrl: renesas: r8a779g0: Add missing SCIF3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/61fdde58e369e8070ffd3c5811c089e6219c7ecc.1717754960.git.geert+renesas@glider.be
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pin groups (GP0_14-18
and GP1_6-10) each named both HSCIF1 and SCIF1. To differentiate, the
pin control driver uses "(h)scif1" and "(h)scif1_x", which were
considered temporary names until the conflict was sorted out.
Fix this by adopting R-Car V4M naming:
- Rename "(h)scif1" to "(h)scif1_a",
- Rename "(h)scif1_x" to "(h)scif1_b".
Adopt the R-Car V4M naming "(h)scif1_a" and "(h)scif1_b" to increase
uniformity.
While at it, remove unneeded separators.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: cf4f789184 ("pinctrl: renesas: r8a779g0: Add missing HSCIF1_X")
Fixes: 9c151c2be9 ("pinctrl: renesas: r8a779g0: Add missing SCIF1_X")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/5009130d1867e12abf9b231c8838fd05e2b28bee.1717754960.git.geert+renesas@glider.be
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pins named both
"FXR_TXEN[AB]". To differentiate, the pin control driver uses
"FXR_TXEN[AB]" and "FXR_TXEN[AB]_X", which were considered temporary
names until the conflict was sorted out.
Fix this by adopting R-Car V4M naming:
- Rename "FXR_TXEN[AB]" to "FXR_TXEN[AB]_A",
- Rename "FXR_TXEN[AB]_X" to "FXR_TXEN[AB]_B".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 1c2646b5ce ("pinctrl: renesas: r8a779g0: Add missing FlexRay")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/5e1e9abb46c311d4c54450d991072d6d0e66f14c.1717754960.git.geert+renesas@glider.be
CAN-FD instance 5 has two alternate pin groups: "canfd5" and "canfd5_b".
Rename the former to "canfd5_a" to increase uniformity.
While at it, remove the unneeded separator.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: c2b4b2cd63 ("pinctrl: renesas: r8a779g0: Add missing CANFD5_B")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/10b22d54086ed11cdfeb0004583029ccf249bdb9.1717754960.git.geert+renesas@glider.be
Add support for the pin controller block on SM4250 Low Power Island.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/20240612-sm4250-lpi-v4-2-a0342e47e21b@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_next_child() will increase refcount of the returned node, need
use of_node_put() on it when done.
Per current implementation, 'child' will be override by
for_each_child_of_node(np, child), so use of_get_child_count to avoid
refcount leakage.
Fixes: 17723111e6 ("pinctrl: add pinctrl-mxs support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/20240504-pinctrl-cleanup-v2-18-26c5f2dc1181@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use scope based of_node_put() cleanup to simplify code.
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/20240504-pinctrl-cleanup-v2-4-26c5f2dc1181@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to finally confine the unsafe gpiochip_get_desc() to
drivers/gpio/, let's convert this driver to using the safer alternative
that takes the gpio_device as argument.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240618111824.15593-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The `PIN_CFG_VARIABLE` macro did not indicate the capabilities of a pin
but served as a flag indicating that the pins of a port have different
capabilities.
To better reflect its purpose, move the `PIN_CFG_VARIABLE` macro beside
`RZG2L_SINGLE_PIN` and rename it to `RZG2L_VARIABLE_CFG`. Additionally,
introduce new macros for packing variable port configurations:
- `RZG2L_GPIO_PORT_PACK_VARIABLE(n, a)`: Combines `RZG2L_VARIABLE_CFG`
with `RZG2L_GPIO_PORT_PACK` to handle variable pin configurations
for a packed port.
- `RZG2L_GPIO_PORT_SPARSE_PACK_VARIABLE(m, a)`: Combines
`RZG2L_VARIABLE_CFG` with `RZG2L_GPIO_PORT_SPARSE_PACK` to handle
variable pin configurations for a sparse port.
Due to the above change the configuration macros have been reorganized
as follows:
- Shift the bit positions of `PIN_CFG_NOGPIO_INT`, `PIN_CFG_NOD`,
`PIN_CFG_SMT`, `PIN_CFG_ELC`, and `PIN_CFG_IOLH_RZV2H` down by one
to accommodate the removal of `PIN_CFG_VARIABLE`.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240618174831.415583-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define `RZG2L_SINGLE_PIN` at the top of the file to clarify its use for
dedicated pins for improved readability.
While at it update the comment for `RZG2L_SINGLE_PIN_PACK` macro and place
it just above the macro for clarity.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240618174831.415583-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Shift the bit masks for `PIN_CFG_PIN_MAP_MASK` and `PIN_CFG_PIN_REG_MASK`,
to accommodate `PIN_CFG_VARIABLE` using `BIT(62)`.
Previously, these bit masks were placed higher up in the bit range, which
did not leave room for `PIN_CFG_VARIABLE` at `BIT(62)`. By adjusting these
masks, we ensure that `PIN_CFG_VARIABLE` can occupy `BIT(62)` without any
conflicts. The updated masks are now:
- `PIN_CFG_PIN_MAP_MASK`: `GENMASK_ULL(61, 54)` (was `GENMASK_ULL(62, 55)`)
- `PIN_CFG_PIN_REG_MASK`: `GENMASK_ULL(53, 46)` (was `GENMASK_ULL(54, 47)`)
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240618174831.415583-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Modify the `PIN_CFG_MASK()` macro to be 32-bit wide. The current maximum
value for `PIN_CFG_*` is `BIT(21)`, which fits within a 32-bit mask.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240618174831.415583-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The fwnode_iomap() function doesn't return error pointers, it returns
NULL. It's the same as of_iomap() in that way. Update the check
accordingly.
Fixes: ecc5bf868673 ("pinctrl: nuvoton: Add ma35d1 pinctrl and GPIO driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/840152f9-d3bb-410e-8164-4c5043e1983e@moroto.mountain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/bcm/pinctrl-bcm4908.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/pinctrl-mcp23s08_i2c.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/pinctrl-mcp23s08_spi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/pinctrl-mcp23s08.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pinctrl/meson/pinctrl-meson.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE().
This includes many meson drivers which, although they did not produce
a warning with the x86 allmodconfig configuration, may cause this
warning with ARM or ARM64 configurations.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # for Amlogic Pinctrl drivers
Link: https://lore.kernel.org/r/20240610-md-drivers-pinctrl-v1-1-68462e3d960c@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While muxing groups of pins at once can be convenient for large
interfaces, it can also be rigid. This is because the group is set to
all pins which support a particular function, even though not all pins
may be used. For example, the sdhci0 function may be used with a 8-bit
eMMC, 4-bit SD card, or even a 1-bit SD card. In these cases, the extra
pins may be repurposed for other uses, but this is not currently
allowed.
There is not too much point in pin "groups" when there are not actual
pin groups at the hardware level. The pins can all be muxed
individually, so there's no point in adding artificial groups on top.
Just mux the pins like the hardware allows.
To this effect, add a new group for each pin which can be muxed. These
groups are part of each function the pin can be muxed to. We treat group
selectors beyond the number of groups as "pin" groups. To set this up,
we initialize groups before functions, and then create a bitmap of used
pins for each function. These used pins are appended to the function's
list of groups.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240610223550.2449230-3-sean.anderson@linux.dev
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
rockchip_pmx_set reset all pinmuxs in group to 0 in the case of error,
add missing bank data retrieval in that code to avoid setting mux on
unexpected pins.
Fixes: 14797189b3 ("pinctrl: rockchip: add return value to rockchip_set_mux")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Link: https://lore.kernel.org/r/20240606125755.53778-5-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
rk3328_pin_ctrl uses type of RK3288 which has a hack in
rockchip_pinctrl_suspend and rockchip_pinctrl_resume to restore GPIO6-C6
at assume, the hack is not applicable to RK3328 as GPIO6 is not even
exist in it. So use a dedicated pinctrl type to skip this hack.
Fixes: 3818e4a767 ("pinctrl: rockchip: Add rk3328 pinctrl support")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Link: https://lore.kernel.org/r/20240606125755.53778-4-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux bits for GPIO3-B1 to GPIO3-B6 pins are not explicitly
specified in RK3328 TRM, however we can get hint from pad name and its
correspinding IOMUX setting for pins in interface descriptions. The
correspinding IOMIX settings for these pins can be found in the same
row next to occurrences of following pad names in RK3328 TRM.
GPIO3-B1: IO_TSPd5m0_CIFdata5m0_GPIO3B1vccio6
GPIO3-B2: IO_TSPd6m0_CIFdata6m0_GPIO3B2vccio6
GPIO3-B3: IO_TSPd7m0_CIFdata7m0_GPIO3B3vccio6
GPIO3-B4: IO_CARDclkm0_GPIO3B4vccio6
GPIO3-B5: IO_CARDrstm0_GPIO3B5vccio6
GPIO3-B6: IO_CARDdetm0_GPIO3B6vccio6
Add pinmux data to rk3328_mux_recalced_data as mux register offset for
these pins does not follow rockchip convention.
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 3818e4a767 ("pinctrl: rockchip: Add rk3328 pinctrl support")
Link: https://lore.kernel.org/r/20240606125755.53778-3-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux bits for GPIO2-B0 to GPIO2-B6 actually have 2 bits width,
correct the bank flag for GPIO2-B. The pinmux bits for GPIO2-B7 is
recalculated so it remain unchanged.
The pinmux bits for those pins are not explicitly specified in RK3328
TRM, however we can get hint from pad name and its correspinding IOMUX
setting for pins in interface descriptions. The correspinding IOMIX
settings for GPIO2-B0 to GPIO2-B6 can be found in the same row next to
occurrences of following pad names in RK3328 TRM.
GPIO2-B0: IO_SPIclkm0_GPIO2B0vccio5
GPIO2-B1: IO_SPItxdm0_GPIO2B1vccio5
GPIO2-B2: IO_SPIrxdm0_GPIO2B2vccio5
GPIO2-B3: IO_SPIcsn0m0_GPIO2B3vccio5
GPIO2-B4: IO_SPIcsn1m0_FLASHvol_sel_GPIO2B4vccio5
GPIO2-B5: IO_ I2C2sda_TSADCshut_GPIO2B5vccio5
GPIO2-B6: IO_ I2C2scl_GPIO2B6vccio5
This fix has been tested on NanoPi R2S for fixing confliting pinmux bits
between GPIO2-B7 with GPIO2-B5.
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 3818e4a767 ("pinctrl: rockchip: Add rk3328 pinctrl support")
Link: https://lore.kernel.org/r/20240606125755.53778-2-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver calls pinctrl_register_and_init() which is not
devm_ managed, it will leads memory leak if pinctrl_enable()
fails. Replace it with devm_pinctrl_register_and_init().
And add missing of_node_put() in the error path.
Fixes: 5038a66dad ("pinctrl: core: delete incorrect free in pinctrl_enable()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240606023704.3931561-4-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver calls pinctrl_register_and_init() which is not
devm_ managed, it will leads memory leak if pinctrl_enable()
fails. Replace it with devm_pinctrl_register_and_init().
And call pcs_free_resources() if pinctrl_enable() fails.
Fixes: 5038a66dad ("pinctrl: core: delete incorrect free in pinctrl_enable()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240606023704.3931561-3-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In devm_pinctrl_register(), if pinctrl_enable() fails in pinctrl_register(),
the "pctldev" has not been added to dev resources, so devm_pinctrl_dev_release()
can not be called, it leads memory leak.
Introduce pinctrl_uninit_controller(), call it in the error path to free memory.
Fixes: 5038a66dad ("pinctrl: core: delete incorrect free in pinctrl_enable()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240606023704.3931561-2-yangyingliang@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In create_pinctrl(), pinctrl_maps_mutex is acquired before calling
add_setting(). If add_setting() returns -EPROBE_DEFER, create_pinctrl()
calls pinctrl_free(). However, pinctrl_free() attempts to acquire
pinctrl_maps_mutex, which is already held by create_pinctrl(), leading to
a potential deadlock.
This patch resolves the issue by releasing pinctrl_maps_mutex before
calling pinctrl_free(), preventing the deadlock.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 42fed7ba44 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Suggested-by: Maximilian Heyne <mheyne@amazon.de>
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240604085838.3344-1-hagarhem@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use modern string_choices API instead of manually determining the
output using ternary operator.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240603181938.76047-3-wahrenst@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 8ff05989b4 ("pinctrl: bcm2835: Make pin freeing behavior
configurable") unintentionally made the module parameter
persist_gpio_outputs changeable at runtime. So drop the write permission
in order to make the freeing behavior predictable for user applications.
Fixes: 8ff05989b4 ("pinctrl: bcm2835: Make pin freeing behavior configurable")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Closes: https://lore.kernel.org/linux-gpio/Zjk-C0nLmlynqLAE@surfacebook.localdomain/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240603181938.76047-2-wahrenst@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing support for LP8764 PMIC in the probe().
Issue detected with v6.10-rc1 (and reproduced with 6.10-rc2) using a TI
J7200 EVM board.
tps6594-pinctrl tps6594-pinctrl.8.auto: error -EINVAL:
Couldn't register gpio_regmap driver
tps6594-pinctrl tps6594-pinctrl.8.auto: probe with driver tps6594-pinctrl
failed with error -22
Fixes: 2088297159 (pinctrl: pinctrl-tps6594: Add TPS65224 PMIC pinctrl and GPIO)
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240603082110.2104977-1-thomas.richard@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
