devm_hwmon_device_unregister() has no in-tree user, and its implementation
is wrong since it does not pass the to-be-removed hardware monitoring
device as parameter. I do not envision a valid use for it; drivers needing
it should not have called devm_hwmon_device_register_with_info() in the
first place. Remove it.
Reported-by: Matthew Sanders <m@ttsande.rs>
Closes: https://lore.kernel.org/linux-hwmon/488b3bdf870ea76c4b943dbe5fd15ac8113019dc.camel@kernel.org/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While the chips supported by this driver do not directly support current
limits, they do support setting shunt voltage limits. The shunt voltage
divided by the shunt resistor value is the current. On top of that,
calibration values are set such that in the shunt voltage register and
the current register report the same values. That means we can report and
configure current limits based on shunt voltage limits, and we can do so
with much better accuracy than by setting shunt voltage limits.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SG2042 use an external MCU to provide basic hardware information
and thermal sensors.
Add driver support for the onboard MCU of SG2042.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Message-ID: <IA1PR20MB49536C786048D1E676BB9C20BB822@IA1PR20MB4953.namprd20.prod.outlook.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the OrangePi NEO-01. It uses different registers for PWM
manual mode, set PWM, and read fan speed than previous devices. Valid PWM
input and duty cycle is 1-244, we scale this from 1-255 to maintain
compatibility with the existing interface.
Add OneXPlayer 2 series, OneXFly, and X1 series models. The 2/X1 series use
new registers for turbo button takeover and read fan speed. X1 has an Intel
variant so change the CPU detection at init to only check for the affected
devices. While at it, adjust formatting of some constants and reorder all
cases alphabetically for consistency. Rename OXP_OLD constants to OXP_MINI
for disambiguation. Update code comments for clarity.
Add support for AYANEO models 2S, AIR 1S, Flip series, GEEK 1S, and KUN.
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Tested-by: Kevin Greenberg <kdgreenberg234@protonmail.com>
Tested-by: Joshua Tam <csinaction@pm.me>
Tested-by: Parth Menon <parthasarathymenon@gmail.com>
Tested-by: Philip Müller <philm@manjaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408160329.TLNbIwRC-lkp@intel.com/
Message-ID: <20240822183525.27289-2-derekjohn.clark@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update datasheet references. Replace misleading 'force parameter needed'
with 'must be instantiated explicitly'. Explain the reason for the missing
auto-detection. Mention all supported chips in Kconfig.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for local caching, to hide register read/write address
differences, and for multi-byte operations. With this change,
the driver specific lock is no longer necessary.
While at it, check errors seen when initializing the chip and bail out
if chip initialization fails.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* Obsolete driver removals
- Removed obsolete adm1021 and max6642 drivers
* New drivers
- MPS MP2891
- MPS MP2993
- MPS MP9941
- MPS MP5920
- SPD5118 (Temperature Sensor and EEPROM)
* Added device support to existing drivers
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
* Notable enhancements and fixes
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827 drivers
* Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEiHPvMQj9QTOCiqgVyx8mb86fmYEFAmaUaiIACgkQyx8mb86f
mYHnbRAAhyaqFF1w5B/XEuZOQ3obG+pAV1ZioE7wXpeRDlniJ9/WgFe4bPpvTNQm
C2LHW6kVtwxybM/FOJz9BN32WiP9v2kp9upb7hhHHo32+5dv57iQR5lB+JC/7lpy
HLisqLrPc5eDQlUiOdeph5fsKyuydxQkefbR1x4shxmcgn+D5M+AYjuAZOA6fSun
spSzgTyPGWgGfhQjSzKoA7DHG3S2pFxRTfqOArvKLOM+ahyOCFuS8Kbq/JpqvalB
moiyIJUeOrgJcTcHSecQ/uFxFiShGBs6EQ1Ao8O9kO0WFw7ke1fw/fWESeTvtiBm
0Z3zfqAIKcnCXvKEupltWXf6kASx5LSlycODTZQlXEROeYhzhJw3J5qF4h0r4+EM
oKmptVLLLekVYrjQlarBtHqpdfnwsL1GuQTk5fZz7ZbG85/ktKV6aGTeKGYdBvll
zZSjz3Jys2u191uxATpJ3vmjaggPylX6dXgmJ9u9lW16+/OnNq7sWURekIfE3F+P
dpZsaia2KN3WAnX/qLQWOOOBbkIIGxn48e+Hi6QY9igVUbY+P/BBfhb9UiWonLKU
exRxAFNV5a4nM0ipJF4odwMqzC9ZjrpY6zFQFZCrG79zOO62/gADUAVzwu2LGGig
p6hqGJmEOkJgYd0zo8KP8ABwgffn8EAtgXBtQU0RS/ls7Z0S58U=
=ebWS
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Obsolete driver removals:
- Removed obsolete adm1021 and max6642 drivers
New drivers:
- MPS MP2891, MP2993, MP9941, and MP5920
- SPD5118 (Temperature Sensor and EEPROM)
Added device support to existing drivers:
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
Notable enhancements and fixes:
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and
with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827
drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (103 commits)
hwmon: (max6697) Fix swapped temp{1,8} critical alarms
hwmon: (max6697) Fix underflow when writing limit attributes
hwmon: Remove obsolete adm1021 and max6642 drivers
hwmon: (pmbus/ltc4286) Drop unused i2c device ids
hwmon: (g762) Initialize fans after configuring clock
hwmon: (amc6821) Add support for pwm1_mode attribute
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Use BIT() and GENMASK()
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc6821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
hwmon: (lm95234) Fix underflows seen when writing limit attributes
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
...
ADM1021, MAX6642, and compatible chips are supported by the lm90 driver.
Remove the obsolete stand-alone drivers to reduce maintenance overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMC6821 supports configuring if a fan is DC or PWM controlled.
Add support for the pwm1_mode attribute to make it runtime configurable.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After setting fan1_target and setting pwm1_enable to 4,
the fan controller tries to achieve the requested fan speed.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip does not have a fan divisor. What it does have is a configuration
to set either 2 or 4 pulses per fan rotation. Rename the attribute to
reflect its use. Update documentation accordingly.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for MPS Hot-Swap controller mp5920. This driver exposes
telemetry and limit value readings and writings.
Signed-off-by: Alex Vdovydchenko <xzeol@yahoo.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240702115252.981416-3-xzeol@yahoo.com
[groeck: Use min_t() to limit length of displayed model string]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading SPD NVMEM data from SPD5118 (Jedec JESD300)
compliant memory modules. NVMEM write operation is not supported.
NVMEM support is optional. If CONFIG_NVMEM is disabled, the driver will
still instantiate but not provide NVMEM attribute files.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for SPD5118 (Jedec JESD300) compliant temperature
sensors. Such sensors are typically found on DDR5 memory modules.
Cc: René Rebe <rene@exactcode.de>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ChromeOS Embedded Controller exposes fan speed and temperature
readings.
Expose this data through the hwmon subsystem.
The driver is designed to be probed via the cros_ec mfd device.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240529-cros_ec-hwmon-v4-2-5cdf0c5db50a@weissschuh.net
[tzungbi: Fixed typo in MAINTAINERS: "chros_ec_hwmon" -> "cros_ec_hwmon"]
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Add the usb id of the HX1200i Series 2023. Update the documentation
accordingly. Also fix the version comments, there are no Series 2022
products. That are legacy or first version products going back many
many years.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/ZlAZs4u0dU7JxtDf@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reporting firmware and bootloader version using debugfs.
Update documentation accordingly.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Link: https://lore.kernel.org/r/20240513194734.43040-2-mail@mariuszachmann.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1428 and EMC1438 are similar to EMC14xx, but have eight temperature
channels, as well as signed data and limit registers. Chips currently
supported by this driver have unsigned registers only.
Signed-off-by: Lars Petter Mostad <larspm@gmail.com>
Link: https://lore.kernel.org/r/20240510142824.824332-1-lars.petter.mostad@appear.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240430085654.1028864-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for NZXT Kraken 2023 (standard) and NZXT Kraken 2023 Elite
all-in-one CPU coolers. These models communicate identically to the NZXT
Kraken Z-series (Z53 code paths) in all cases except when writing the
fan curve, where setting additional bits in the report is needed.
Reviewed-by: Jonas Malaco <jonas@protocubo.io>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240428104812.14037-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Infineon XDP710.This is a Hot-Swap Controller.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240425153608.4003782-2-peteryin.openbmc@gmail.com
[groeck: s/microOhmRsense/micro_ohm_osense/g; declared array static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for ADP1050 Digital Controller for Isolated Power Supplies
with PMBus interface Voltage, Current and Temperature Monitor.
The ADP1050 implements several features to enable a robust
system of parallel and redundant operation for customers who
require high availability. The device can measure voltage,
current and temperature that can be used in different
techniques to identify and safely shut down an erroneous
power supply in parallel operation mode.
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Link: https://lore.kernel.org/r/20240321142201.10330-2-radu.sabau@analog.com
[groeck: Fixed corrupted link in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update links in the documentation and in-code comments which point to
the datasheet.
The current links don't work because National Semiconductor (which is the
original manufacturer of this chip) has been a part of Texas Instruments
since 2011 and http://www.national.com/ doesn't work anymore.
Fixes: e1a8e913f9 ("[PATCH] lm70: New hardware monitoring driver")
Signed-off-by: Kousik Sanagavarapu <five231003@gmail.com>
Link: https://lore.kernel.org/r/20240318154540.90613-3-five231003@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver support two functions: PWM and Tachometer. The PWM feature can
handle up to 16 output ports, while the Tachometer can monitor to up to 16
input ports as well. This driver implements them by exposing two kernel
subsystems: PWM and HWMON. The PWM subsystem can be utilized alongside
existing drivers for controlling elements such as fans (pwm-fan.c),
beepers (pwm-beeper.c) and so on. Through the HWMON subsystem, the driver
provides sysfs interfaces for fan.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240221104025.1306227-4-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The URL for the MAX6620 datasheet has changed. Update it to reflect the
current location.
Signed-off-by: Okan Akyuz <okanakyuz@okanakyuz.com>
Link: https://lore.kernel.org/r/20240216075212.69118-1-okanakyuz@okanakyuz.com
[groeck: Updated subject and patch description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for handheld AYANEO AIR Plus with the same EC registers
to add proper fan control.
Functionality was tested successfully.
Signed-off-by: Sebastian Kranz <tklightforce@googlemail.com>
Link: https://lore.kernel.org/r/20240209090157.3232-1-tklightforce@googlemail.com
[groeck: Fixed up commit message]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the ASUS ROG RYUJIN II 360
all-in-one CPU liquid cooler, which communicates through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] by
Florian Freudiger.
Available sensors are pump, internal and external
(controller) fan speed in RPM, their duties in PWM, as well as
coolant temperature.
Attaching external fans to the controller is optional and allows them
to be controlled from the device. If not connected, the fan-related
sensors will report zeroes. The controller is a separate hardware unit
that comes bundled with the AIO and connects to it to allow fan control.
The addressable LCD screen is not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/pull/653
Tested-by: Florian Freudiger <florian.freudiger@proton.me>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240108094453.22986-1-savicaleksa83@gmail.com
[groeck: Add HID dependency]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver enables hardware monitoring support for NZXT Kraken
X53/X63/X73 and Z53/Z63/Z73 all-in-one CPU liquid coolers.
All models expose liquid temperature and pump speed (in RPM), as well as
PWM control (natively only through a temp-PWM curve, but the driver also
emulates fixed PWM control on top of that). The Z-series models
additionally expose the speed and duty of an optionally connected fan,
with the same PWM control capabilities.
Pump and fan duty control mode can be set through pwm[1-2]_enable,
where 1 is for the manual control mode and 2 is for the liquid temp
to PWM curve mode. Writing a 0 disables control of the channel through
the driver after setting its duty to 100%. As it is not possible to query
the device for the active mode, the driver keeps track of it.
The temperature of the curves relates to the fixed [20-59] C range, per
device limitations, and correlating to the detected liquid temperature.
Only PWM values (ranging from 0-255) can be set.
The addressable RGB LEDs and LCD screen, included only on Z-series models,
are not supported in this driver.
Co-developed-by: Jonas Malaco <jonas@protocubo.io>
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Co-developed-by: Yury Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Yury Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240129111932.368232-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Amphenol ChipCap 2 is a capacitive polymer humidity and temperature
sensor with an integrated EEPROM and minimum/maximum humidity alarms.
All device variants offer an I2C interface and depending on the part
number, two different output modes:
- CC2D: digital output
- CC2A: analog (PDM) output
This driver adds support for the digital variant (CC2D part numbers),
which includes the following part numbers:
- non-sleep measurement mode (CC2D23, CC2D25, CC2D33, CC2D35)
- sleep measurement mode (CC2D23S, CC2D25S, CC2D33S, CC2D35S)
The Chipcap 2 EEPROM can be accessed to configure a series of parameters
like the minimum/maximum humidity alarm threshold and hysteresis. The
EEPROM is only accessible in the command window after a power-on reset.
The default window lasts 10 ms if no Start_CM command is sent. After the
command window is finished (either after the mentioned timeout of after
a Start_NOM command is sent), the device enters the normal operation
mode and makes a first measurement automatically.
Unfortunately, the device does not provide any hardware or software
reset and therefore the driver must trigger power cycles to enter the
command mode. A dedicated, external regulator is required for that.
This driver keeps the device off until a measurement or access to the
EEPROM is required, making use of the first automatic measurement to
avoid different code paths for sleep and non-sleep devices.
The minimum and maximum humidity alarms are configured with two
registers per alarm: one stores the alarm threshold and the other one
keeps the value that turns off the alarm. The alarm signals are only
updated when a measurement is carried out.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240130-topic-chipcap2-v6-5-260bea05cf9b@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature/humidity sensors of the STS3x/SHT3x family are
calibrated and factory-programmed with a unique serial number.
For some sensors, this serial number can be used to obtain a calibration
certificate via an API provided by the manufacturer (Sensirion).
Expose the serial number via debugfs.
Tested with: 2x STS31, 1x STS32, 1x SHT31
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
Link: https://lore.kernel.org/r/20240131111512.25321-2-code@stefan-gloor.ch
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mpq8785 device from Monolithic Power Systems, Inc.
(MPS) vendor. This is synchronous step-down controller.
Signed-off-by: Charles Hsu <ythsu0511@gmail.com>
Link: https://lore.kernel.org/r/20240131074822.2962078-2-ythsu0511@gmail.com
[groeck: probe_new --> probe; add MODULE_IMPORT_NS(PMBUS)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds a driver that provides read only access to the fan speed for Microsoft
Surface Pro devices. The fan speed is always regulated by the EC and cannot
be influenced directly.
Signed-off-by: Ivor Wanders <ivor@iwanders.net>
Link: https://github.com/linux-surface/kernel/pull/144
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20240131005856.10180-2-ivor@iwanders.net
[groeck:
- Declare surface_fan_hwmon_is_visible() static
- Add dependency on SURFACE_AGGREGATOR_BUS
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC4282 hot swap controller allows a board to be safely inserted and
removed from a live backplane. Using one or more external N-channel pass
transistors, board supply voltage and inrush current are ramped up at an
adjustable rate. An I2C interface and onboard ADC allows for monitoring
of board current, voltage, power, energy and fault status.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240129-b4-ltc4282-support-v4-3-fe75798164cc@analog.com
[groeck: clamp value range in ltc4282_write_voltage_byte_cached()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Class-based I2C probing requires detect() and address_list both
to be set in the I2C client driver, see checks in i2c_detect().
It's misleading to declare I2C_CLASS_HWMON support if the driver
doesn't implement detect().
Class-based probing is a legacy mechanism, in addition apparently
nobody ever noticed that class-based probing has been non-functional
in both drivers from the very beginning. So drop the fragments of
class-based probing support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/13ce7c11-a958-4892-ada9-faf5bfdcb89d@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
as6200 is a temperature sensor with 0.0625°C resolution and a
range between -40°C to 125°C.
By default, the driver configures as6200 as following:
- Converstion rate: 8 Hz
- Conversion mode: continuous
- Consecutive fault counts: 4 samples
- Alert state: high polarity
- Alert mode: comparator mode
Interrupt is supported for the alert pin.
Signed-off-by: Abdel Alkuor <alkuor@gmail.com>
Link: https://lore.kernel.org/r/d1686678991bf8ee0d00cb08ca046798f37ca4b3.1703127334.git.alkuor@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp2856/mp2857 device from Monolithic Power Systems, Inc.
(MPS) vendor. This is a dual-loop, digital, multi-phase,
modulation controller.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Signed-off-by: Potin Lai <potin.lai.pt@gmail.com>
Link: https://lore.kernel.org/r/20231211160519.21254-3-potin.lai.pt@gmail.com
[groeck: Fix checkpatch issues, use i2c_get_match_data()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Gigabyte AORUS Waterforce
all-in-one CPU liquid coolers, which communicate through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] and
confirmed by me on a Waterforce X240 by observing the sent reports from
the official software.
Available sensors are pump and fan speed in RPM, as well as coolant
temperature. Also available through debugfs is the firmware version.
Attaching a fan is optional and allows it to be controlled from the
device. If it's not connected, the fan-related sensors will report
zeroes.
The addressable RGB LEDs and LCD screen are not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/issues/167
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231207122402.107032-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
