Merge branch 'imx-nvmem' into thermal-soc

Documentation/devicetree/bindings/thermal/imx-thermal.txt

@@ -7,10 +7,17 @@ Required properties:
   is higher than panic threshold, system will auto reboot by SRC module.
 - fsl,tempmon : phandle pointer to system controller that contains TEMPMON
   control registers, e.g. ANATOP on imx6q.
+- nvmem-cells: A phandle to the calibration cells provided by ocotp.
+- nvmem-cell-names: Should be "calib", "temp_grade".
+
+Deprecated properties:
 - fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON
   calibration data, e.g. OCOTP on imx6q.  The details about calibration data
   can be found in SoC Reference Manual.
 
+Direct access to OCOTP via fsl,tempmon-data is incorrect on some newer chips
+because it does not handle OCOTP clock requirements.
+
 Optional properties:
 - clocks : thermal sensor's clock source.
 

drivers/thermal/Kconfig

@@ -206,6 +206,7 @@ config HISI_THERMAL
 config IMX_THERMAL
 	tristate "Temperature sensor driver for Freescale i.MX SoCs"
 	depends on (ARCH_MXC && CPU_THERMAL) || COMPILE_TEST
+	depends on NVMEM || !NVMEM
 	depends on MFD_SYSCON
 	depends on OF
 	help

drivers/thermal/imx_thermal.c

@@ -25,6 +25,7 @@
 #include <linux/slab.h>
 #include <linux/thermal.h>
 #include <linux/types.h>
+#include <linux/nvmem-consumer.h>
 
 #define REG_SET		0x4
 #define REG_CLR		0x8
@@ -94,7 +95,7 @@ struct imx_thermal_data {
 	struct thermal_cooling_device *cdev;
 	enum thermal_device_mode mode;
 	struct regmap *tempmon;
-	u32 c1, c2; /* See formula in imx_get_sensor_data() */
+	u32 c1, c2; /* See formula in imx_init_calib() */
 	int temp_passive;
 	int temp_critical;
 	int temp_max;
@@ -177,7 +178,7 @@ static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
 
 	n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >> TEMPSENSE0_TEMP_CNT_SHIFT;
 
-	/* See imx_get_sensor_data() for formula derivation */
+	/* See imx_init_calib() for formula derivation */
 	*temp = data->c2 - n_meas * data->c1;
 
 	/* Update alarm value to next higher trip point for TEMPMON_IMX6Q */
@@ -346,29 +347,12 @@ static struct thermal_zone_device_ops imx_tz_ops = {
 	.set_trip_temp = imx_set_trip_temp,
 };
 
-static int imx_get_sensor_data(struct platform_device *pdev)
+static int imx_init_calib(struct platform_device *pdev, u32 val)
 {
 	struct imx_thermal_data *data = platform_get_drvdata(pdev);
-	struct regmap *map;
 	int t1, n1;
-	int ret;
-	u32 val;
 	u64 temp64;
 
-	map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
-					      "fsl,tempmon-data");
-	if (IS_ERR(map)) {
-		ret = PTR_ERR(map);
-		dev_err(&pdev->dev, "failed to get sensor regmap: %d\n", ret);
-		return ret;
-	}
-
-	ret = regmap_read(map, OCOTP_ANA1, &val);
-	if (ret) {
-		dev_err(&pdev->dev, "failed to read sensor data: %d\n", ret);
-		return ret;
-	}
-
 	if (val == 0 || val == ~0) {
 		dev_err(&pdev->dev, "invalid sensor calibration data\n");
 		return -EINVAL;
@@ -405,12 +389,12 @@ static int imx_get_sensor_data(struct platform_device *pdev)
 	data->c1 = temp64;
 	data->c2 = n1 * data->c1 + 1000 * t1;
 
-	/* use OTP for thermal grade */
-	ret = regmap_read(map, OCOTP_MEM0, &val);
-	if (ret) {
-		dev_err(&pdev->dev, "failed to read temp grade: %d\n", ret);
-		return ret;
-	}
+	return 0;
+}
+
+static void imx_init_temp_grade(struct platform_device *pdev, u32 val)
+{
+	struct imx_thermal_data *data = platform_get_drvdata(pdev);
 
 	/* The maximum die temp is specified by the Temperature Grade */
 	switch ((val >> 6) & 0x3) {
@@ -438,6 +422,55 @@ static int imx_get_sensor_data(struct platform_device *pdev)
 	 */
 	data->temp_critical = data->temp_max - (1000 * 5);
 	data->temp_passive = data->temp_max - (1000 * 10);
+}
+
+static int imx_init_from_tempmon_data(struct platform_device *pdev)
+{
+	struct regmap *map;
+	int ret;
+	u32 val;
+
+	map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+					      "fsl,tempmon-data");
+	if (IS_ERR(map)) {
+		ret = PTR_ERR(map);
+		dev_err(&pdev->dev, "failed to get sensor regmap: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_read(map, OCOTP_ANA1, &val);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to read sensor data: %d\n", ret);
+		return ret;
+	}
+	ret = imx_init_calib(pdev, val);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(map, OCOTP_MEM0, &val);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to read sensor data: %d\n", ret);
+		return ret;
+	}
+	imx_init_temp_grade(pdev, val);
+
+	return 0;
+}
+
+static int imx_init_from_nvmem_cells(struct platform_device *pdev)
+{
+	int ret;
+	u32 val;
+
+	ret = nvmem_cell_read_u32(&pdev->dev, "calib", &val);
+	if (ret)
+		return ret;
+	imx_init_calib(pdev, val);
+
+	ret = nvmem_cell_read_u32(&pdev->dev, "temp_grade", &val);
+	if (ret)
+		return ret;
+	imx_init_temp_grade(pdev, val);
 
 	return 0;
 }
@@ -514,10 +547,21 @@ static int imx_thermal_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, data);
 
-	ret = imx_get_sensor_data(pdev);
-	if (ret) {
-		dev_err(&pdev->dev, "failed to get sensor data\n");
-		return ret;
+	if (of_find_property(pdev->dev.of_node, "nvmem-cells", NULL)) {
+		ret = imx_init_from_nvmem_cells(pdev);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+		if (ret) {
+			dev_err(&pdev->dev, "failed to init from nvmem: %d\n",
+				ret);
+			return ret;
+		}
+	} else {
+		ret = imx_init_from_tempmon_data(pdev);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to init from from fsl,tempmon-data\n");
+			return ret;
+		}
 	}
 
 	/* Make sure sensor is in known good state for measurements */