Merge remote-tracking branches 'spi/topic/sirf', 'spi/topic/spidev' and 'spi/topic/zynq' into spi-next

Documentation/devicetree/bindings/spi/spi-sirf.txt

@@ -1,7 +1,8 @@
 * CSR SiRFprimaII Serial Peripheral Interface
 
 Required properties:
-- compatible : Should be "sirf,prima2-spi"
+- compatible : Should be "sirf,prima2-spi", "sirf,prima2-usp"
+               or "sirf,atlas7-usp"
 - reg : Offset and length of the register set for the device
 - interrupts : Should contain SPI interrupt
 - resets: phandle to the reset controller asserting this device in

Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt

@@ -0,0 +1,26 @@
+Xilinx Zynq UltraScale+ MPSoC GQSPI controller Device Tree Bindings
+-------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,zynqmp-qspi-1.0".
+- reg			: Physical base address and size of GQSPI registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupt-parent	: Must be core interrupt controller.
+- clock-names		: List of input clock names - "ref_clk", "pclk"
+			  (See clock bindings for details).
+- clocks		: Clock phandles (see clock bindings for details).
+
+Optional properties:
+- num-cs		: Number of chip selects used.
+
+Example:
+	qspi: spi@ff0f0000 {
+		compatible = "xlnx,zynqmp-qspi-1.0";
+		clock-names = "ref_clk", "pclk";
+		clocks = <&misc_clk &misc_clk>;
+		interrupts = <0 15 4>;
+		interrupt-parent = <&gic>;
+		num-cs = <1>;
+		reg = <0x0 0xff0f0000 0x1000>,<0x0 0xc0000000 0x8000000>;
+	};

drivers/spi/Kconfig

@@ -610,6 +610,12 @@ config SPI_XTENSA_XTFPGA
 	  16 bit words in SPI mode 0, automatically asserting CS on transfer
 	  start and deasserting on end.
 
+config SPI_ZYNQMP_GQSPI
+	tristate "Xilinx ZynqMP GQSPI controller"
+	depends on SPI_MASTER
+	help
+	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
+
 config SPI_NUC900
 	tristate "Nuvoton NUC900 series SPI"
 	depends on ARCH_W90X900

drivers/spi/Makefile

@@ -89,3 +89,4 @@ obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
 obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
 obj-$(CONFIG_SPI_XTENSA_XTFPGA)		+= spi-xtensa-xtfpga.o
+obj-$(CONFIG_SPI_ZYNQMP_GQSPI)		+= spi-zynqmp-gqspi.o

drivers/spi/spidev.c

@@ -95,37 +95,25 @@ MODULE_PARM_DESC(bufsiz, "data bytes in biggest supported SPI message");
 
 /*-------------------------------------------------------------------------*/
 
-/*
- * We can't use the standard synchronous wrappers for file I/O; we
- * need to protect against async removal of the underlying spi_device.
- */
-static void spidev_complete(void *arg)
-{
-	complete(arg);
-}
-
 static ssize_t
 spidev_sync(struct spidev_data *spidev, struct spi_message *message)
 {
 	DECLARE_COMPLETION_ONSTACK(done);
 	int status;
-
-	message->complete = spidev_complete;
-	message->context = &done;
+	struct spi_device *spi;
 
 	spin_lock_irq(&spidev->spi_lock);
-	if (spidev->spi == NULL)
-		status = -ESHUTDOWN;
-	else
-		status = spi_async(spidev->spi, message);
+	spi = spidev->spi;
 	spin_unlock_irq(&spidev->spi_lock);
 
-	if (status == 0) {
-		wait_for_completion(&done);
-		status = message->status;
-		if (status == 0)
-			status = message->actual_length;
-	}
+	if (spi == NULL)
+		status = -ESHUTDOWN;
+	else
+		status = spi_sync(spi, message);
+
+	if (status == 0)
+		status = message->actual_length;
+
 	return status;
 }
 
@@ -647,7 +635,6 @@ err_find_dev:
 static int spidev_release(struct inode *inode, struct file *filp)
 {
 	struct spidev_data	*spidev;
-	int			status = 0;
 
 	mutex_lock(&device_list_lock);
 	spidev = filp->private_data;
@@ -676,7 +663,7 @@ static int spidev_release(struct inode *inode, struct file *filp)
 	}
 	mutex_unlock(&device_list_lock);
 
-	return status;
+	return 0;
 }
 
 static const struct file_operations spidev_fops = {