Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-11-10 06:01:57 +00:00
Code Issues Packages Projects Releases Wiki Activity

spi: Enable controllers to extend the SPI protocol with MOSI idle configuration

Browse Source 
The behavior of an SPI controller data output line (SDO or MOSI or COPI
(Controller Output Peripheral Input) for disambiguation) is usually not
specified when the controller is not clocking out data on SCLK edges.
However, there do exist SPI peripherals that require specific MOSI line
state when data is not being clocked out of the controller.

Conventional SPI controllers may set the MOSI line on SCLK edges then bring
it low when no data is going out or leave the line the state of the last
transfer bit. More elaborated controllers are capable to set the MOSI idle
state according to different configurable levels and thus are more suitable
for interfacing with demanding peripherals.

Add SPI mode bits to allow peripherals to request explicit MOSI idle state
when needed.

When supporting a particular MOSI idle configuration, the data output line
state is expected to remain at the configured level when the controller is
not clocking out data. When a device that needs a specific MOSI idle state
is identified, its driver should request the MOSI idle configuration by
setting the proper SPI mode bit.

Acked-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Tested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/9802160b5e5baed7f83ee43ac819cb757a19be55.1720810545.git.marcelo.schmitt@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit is contained in:
Marcelo Schmitt 2024-07-12 16:20:36 -03:00 committed by Mark Brown
parent 8400291e28
commit f58872f45c
No known key found for this signature in database
GPG Key ID: 24D68B725D5487D0
3 changed files with 92 additions and 2 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

83
Documentation/spi/spi-summary.rst
View File

@ -614,6 +614,89 @@ queue, and then start some asynchronous transfer engine (unless it's
already running).
Extensions to the SPI protocol
------------------------------
The fact that SPI doesn't have a formal specification or standard permits chip
manufacturers to implement the SPI protocol in slightly different ways. In most
cases, SPI protocol implementations from different vendors are compatible among
each other. For example, in SPI mode 0 (CPOL=0, CPHA=0) the bus lines may behave
like the following:
::
nCSx ___ ___
\_________________________________________________________________/
• •
• •
SCLK ___ ___ ___ ___ ___ ___ ___ ___
_______/ \___/ \___/ \___/ \___/ \___/ \___/ \___/ \_____
• : ; : ; : ; : ; : ; : ; : ; : ; •
• : ; : ; : ; : ; : ; : ; : ; : ; •
MOSI XXX__________ _______ _______ ________XXX
0xA5 XXX__/ 1 \_0_____/ 1 \_0_______0_____/ 1 \_0_____/ 1 \_XXX
• ; ; ; ; ; ; ; ; •
• ; ; ; ; ; ; ; ; •
MISO XXX__________ _______________________ _______ XXX
0xBA XXX__/ 1 \_____0_/ 1 1 1 \_____0__/ 1 \____0__XXX
Legend::
• marks the start/end of transmission;
: marks when data is clocked into the peripheral;
; marks when data is clocked into the controller;
X marks when line states are not specified.
In some few cases, chips extend the SPI protocol by specifying line behaviors
that other SPI protocols don't (e.g. data line state for when CS is not
asserted). Those distinct SPI protocols, modes, and configurations are supported
by different SPI mode flags.
MOSI idle state configuration
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common SPI protocol implementations don't specify any state or behavior for the
MOSI line when the controller is not clocking out data. However, there do exist
peripherals that require specific MOSI line state when data is not being clocked
out. For example, if the peripheral expects the MOSI line to be high when the
controller is not clocking out data (``SPI_MOSI_IDLE_HIGH``), then a transfer in
SPI mode 0 would look like the following:
::
nCSx ___ ___
\_________________________________________________________________/
• •
• •
SCLK ___ ___ ___ ___ ___ ___ ___ ___
_______/ \___/ \___/ \___/ \___/ \___/ \___/ \___/ \_____
• : ; : ; : ; : ; : ; : ; : ; : ; •
• : ; : ; : ; : ; : ; : ; : ; : ; •
MOSI _____ _______ _______ _______________ ___
0x56 \_0_____/ 1 \_0_____/ 1 \_0_____/ 1 1 \_0_____/
• ; ; ; ; ; ; ; ; •
• ; ; ; ; ; ; ; ; •
MISO XXX__________ _______________________ _______ XXX
0xBA XXX__/ 1 \_____0_/ 1 1 1 \_____0__/ 1 \____0__XXX
Legend::
• marks the start/end of transmission;
: marks when data is clocked into the peripheral;
; marks when data is clocked into the controller;
X marks when line states are not specified.
In this extension to the usual SPI protocol, the MOSI line state is specified to
be kept high when CS is asserted but the controller is not clocking out data to
the peripheral and also when CS is not asserted.
Peripherals that require this extension must request it by setting the
``SPI_MOSI_IDLE_HIGH`` bit into the mode attribute of their ``struct
spi_device`` and call spi_setup(). Controllers that support this extension
should indicate it by setting ``SPI_MOSI_IDLE_HIGH`` in the mode_bits attribute
of their ``struct spi_controller``. The configuration to idle MOSI low is
analogous but uses the ``SPI_MOSI_IDLE_LOW`` mode bit.
THANKS TO
---------
Contributors to Linux-SPI discussions include (in alphabetical order,

6
drivers/spi/spi.c
View File

@ -3921,6 +3921,12 @@ int spi_setup(struct spi_device *spi)
(SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL |
SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL)))
return -EINVAL;
/* Check against conflicting MOSI idle configuration */
if ((spi->mode & SPI_MOSI_IDLE_LOW) && (spi->mode & SPI_MOSI_IDLE_HIGH)) {
dev_err(&spi->dev,
"setup: MOSI configured to idle low and high at the same time.\n");
return -EINVAL;
}
/*
* Help drivers fail *cleanly* when they need options
* that aren't supported with their current controller.

5
include/uapi/linux/spi/spi.h
View File

@ -28,7 +28,8 @@
#define SPI_RX_OCTAL _BITUL(14) /* receive with 8 wires */
#define SPI_3WIRE_HIZ _BITUL(15) /* high impedance turnaround */
#define SPI_RX_CPHA_FLIP _BITUL(16) /* flip CPHA on Rx only xfer */
#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave mosi line low when idle */
#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave MOSI line low when idle */
#define SPI_MOSI_IDLE_HIGH _BITUL(18) /* leave MOSI line high when idle */
/*
* All the bits defined above should be covered by SPI_MODE_USER_MASK.
@ -38,6 +39,6 @@
* These bits must not overlap. A static assert check should make sure of that.
* If adding extra bits, make sure to increase the bit index below as well.
*/
#define SPI_MODE_USER_MASK (_BITUL(18) - 1)
#define SPI_MODE_USER_MASK (_BITUL(19) - 1)
#endif /* _UAPI_SPI_H */