diff --git a/drivers/dma/mxs-dma.c b/drivers/dma/mxs-dma.c
index c622bee7eb12..20a9cb7cb6d3 100644
--- a/drivers/dma/mxs-dma.c
+++ b/drivers/dma/mxs-dma.c
@@ -78,6 +78,7 @@
 #define BM_CCW_COMMAND		(3 << 0)
 #define CCW_CHAIN		(1 << 2)
 #define CCW_IRQ			(1 << 3)
+#define CCW_WAIT4RDY		(1 << 5)
 #define CCW_DEC_SEM		(1 << 6)
 #define CCW_WAIT4END		(1 << 7)
 #define CCW_HALT_ON_TERM	(1 << 8)
@@ -547,6 +548,8 @@ static struct dma_async_tx_descriptor *mxs_dma_prep_slave_sg(
 		ccw->bits |= CCW_TERM_FLUSH;
 		ccw->bits |= BF_CCW(sg_len, PIO_NUM);
 		ccw->bits |= BF_CCW(MXS_DMA_CMD_NO_XFER, COMMAND);
+		if (flags & MXS_DMA_CTRL_WAIT4RDY)
+			ccw->bits |= CCW_WAIT4RDY;
 	} else {
 		for_each_sg(sgl, sg, sg_len, i) {
 			if (sg_dma_len(sg) > MAX_XFER_BYTES) {
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
index d088b3e77fef..5db84178edff 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -528,26 +528,12 @@ static int common_nfc_set_geometry(struct gpmi_nand_data *this)
 static int bch_set_geometry(struct gpmi_nand_data *this)
 {
 	struct resources *r = &this->resources;
-	struct bch_geometry *bch_geo = &this->bch_geometry;
-	unsigned int block_count;
-	unsigned int block_size;
-	unsigned int metadata_size;
-	unsigned int ecc_strength;
-	unsigned int page_size;
-	unsigned int gf_len;
 	int ret;
 
 	ret = common_nfc_set_geometry(this);
 	if (ret)
 		return ret;
 
-	block_count   = bch_geo->ecc_chunk_count - 1;
-	block_size    = bch_geo->ecc_chunk_size;
-	metadata_size = bch_geo->metadata_size;
-	ecc_strength  = bch_geo->ecc_strength >> 1;
-	page_size     = bch_geo->page_size;
-	gf_len        = bch_geo->gf_len;
-
 	ret = pm_runtime_get_sync(this->dev);
 	if (ret < 0)
 		return ret;
@@ -561,27 +547,9 @@ static int bch_set_geometry(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
-	/* Configure layout 0. */
-	writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count)
-			| BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size)
-			| BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this)
-			| BF_BCH_FLASH0LAYOUT0_GF(gf_len, this)
-			| BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this),
-			r->bch_regs + HW_BCH_FLASH0LAYOUT0);
-
-	writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size)
-			| BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this)
-			| BF_BCH_FLASH0LAYOUT1_GF(gf_len, this)
-			| BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this),
-			r->bch_regs + HW_BCH_FLASH0LAYOUT1);
-
 	/* Set *all* chip selects to use layout 0. */
 	writel(0, r->bch_regs + HW_BCH_LAYOUTSELECT);
 
-	/* Enable interrupts. */
-	writel(BM_BCH_CTRL_COMPLETE_IRQ_EN,
-				r->bch_regs + HW_BCH_CTRL_SET);
-
 	ret = 0;
 err_out:
 	pm_runtime_mark_last_busy(this->dev);
@@ -795,32 +763,6 @@ static void gpmi_clear_bch(struct gpmi_nand_data *this)
 	writel(BM_BCH_CTRL_COMPLETE_IRQ, r->bch_regs + HW_BCH_CTRL_CLR);
 }
 
-/* Returns the Ready/Busy status of the given chip. */
-static int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip)
-{
-	struct resources *r = &this->resources;
-	uint32_t mask = 0;
-	uint32_t reg = 0;
-
-	if (GPMI_IS_MX23(this)) {
-		mask = MX23_BM_GPMI_DEBUG_READY0 << chip;
-		reg = readl(r->gpmi_regs + HW_GPMI_DEBUG);
-	} else if (GPMI_IS_MX28(this) || GPMI_IS_MX6(this)) {
-		/*
-		 * In the imx6, all the ready/busy pins are bound
-		 * together. So we only need to check chip 0.
-		 */
-		if (GPMI_IS_MX6(this))
-			chip = 0;
-
-		/* MX28 shares the same R/B register as MX6Q. */
-		mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip);
-		reg = readl(r->gpmi_regs + HW_GPMI_STAT);
-	} else
-		dev_err(this->dev, "unknown arch.\n");
-	return reg & mask;
-}
-
 static struct dma_chan *get_dma_chan(struct gpmi_nand_data *this)
 {
 	/* We use the DMA channel 0 to access all the nand chips. */
@@ -836,29 +778,6 @@ static void dma_irq_callback(void *param)
 	complete(dma_c);
 }
 
-static int start_dma_without_bch_irq(struct gpmi_nand_data *this,
-				     struct dma_async_tx_descriptor *desc)
-{
-	struct completion *dma_c = &this->dma_done;
-	unsigned long timeout;
-
-	init_completion(dma_c);
-
-	desc->callback		= dma_irq_callback;
-	desc->callback_param	= this;
-	dmaengine_submit(desc);
-	dma_async_issue_pending(get_dma_chan(this));
-
-	/* Wait for the interrupt from the DMA block. */
-	timeout = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000));
-	if (!timeout) {
-		dev_err(this->dev, "DMA timeout, last DMA\n");
-		gpmi_dump_info(this);
-		return -ETIMEDOUT;
-	}
-	return 0;
-}
-
 static irqreturn_t bch_irq(int irq, void *cookie)
 {
 	struct gpmi_nand_data *this = cookie;
@@ -868,83 +787,25 @@ static irqreturn_t bch_irq(int irq, void *cookie)
 	return IRQ_HANDLED;
 }
 
-/*
- * This function is used in BCH reading or BCH writing pages.
- * It will wait for the BCH interrupt as long as ONE second.
- * Actually, we must wait for two interrupts :
- *	[1] firstly the DMA interrupt and
- *	[2] secondly the BCH interrupt.
- */
-static int start_dma_with_bch_irq(struct gpmi_nand_data *this,
-				  struct dma_async_tx_descriptor *desc)
+static int gpmi_raw_len_to_len(struct gpmi_nand_data *this, int raw_len)
 {
-	struct completion *bch_c = &this->bch_done;
-	unsigned long timeout;
-
-	/* Prepare to receive an interrupt from the BCH block. */
-	init_completion(bch_c);
-
-	/* start the DMA */
-	start_dma_without_bch_irq(this, desc);
-
-	/* Wait for the interrupt from the BCH block. */
-	timeout = wait_for_completion_timeout(bch_c, msecs_to_jiffies(1000));
-	if (!timeout) {
-		dev_err(this->dev, "BCH timeout\n");
-		gpmi_dump_info(this);
-		return -ETIMEDOUT;
-	}
-	return 0;
-}
-
-static int gpmi_send_command(struct gpmi_nand_data *this)
-{
-	struct dma_chan *channel = get_dma_chan(this);
-	struct dma_async_tx_descriptor *desc;
-	struct scatterlist *sgl;
-	int chip = this->current_chip;
-	int ret;
-	u32 pio[3];
-
-	/* [1] send out the PIO words */
-	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_CLE)
-		| BM_GPMI_CTRL0_ADDRESS_INCREMENT
-		| BF_GPMI_CTRL0_XFER_COUNT(this->command_length);
-	pio[1] = pio[2] = 0;
-	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
-				      DMA_TRANS_NONE, 0);
-	if (!desc)
-		return -EINVAL;
-
-	/* [2] send out the COMMAND + ADDRESS string stored in @buffer */
-	sgl = &this->cmd_sgl;
-
-	sg_init_one(sgl, this->cmd_buffer, this->command_length);
-	dma_map_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
-	desc = dmaengine_prep_slave_sg(channel,
-				sgl, 1, DMA_MEM_TO_DEV,
-				MXS_DMA_CTRL_WAIT4END);
-	if (!desc)
-		return -EINVAL;
-
-	/* [3] submit the DMA */
-	ret = start_dma_without_bch_irq(this, desc);
-
-	dma_unmap_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
-
-	return ret;
+	/*
+	 * raw_len is the length to read/write including bch data which
+	 * we are passed in exec_op. Calculate the data length from it.
+	 */
+	if (this->bch)
+		return ALIGN_DOWN(raw_len, this->bch_geometry.ecc_chunk_size);
+	else
+		return raw_len;
 }
 
 /* Can we use the upper's buffer directly for DMA? */
 static bool prepare_data_dma(struct gpmi_nand_data *this, const void *buf,
-			     int len, enum dma_data_direction dr)
+			     int raw_len, struct scatterlist *sgl,
+			     enum dma_data_direction dr)
 {
-	struct scatterlist *sgl = &this->data_sgl;
 	int ret;
+	int len = gpmi_raw_len_to_len(this, raw_len);
 
 	/* first try to map the upper buffer directly */
 	if (virt_addr_valid(buf) && !object_is_on_stack(buf)) {
@@ -960,7 +821,7 @@ map_fail:
 	/* We have to use our own DMA buffer. */
 	sg_init_one(sgl, this->data_buffer_dma, len);
 
-	if (dr == DMA_TO_DEVICE)
+	if (dr == DMA_TO_DEVICE && buf != this->data_buffer_dma)
 		memcpy(this->data_buffer_dma, buf, len);
 
 	dma_map_sg(this->dev, sgl, 1, dr);
@@ -968,208 +829,6 @@ map_fail:
 	return false;
 }
 
-static int gpmi_send_data(struct gpmi_nand_data *this, const void *buf, int len)
-{
-	struct dma_async_tx_descriptor *desc;
-	struct dma_chan *channel = get_dma_chan(this);
-	int chip = this->current_chip;
-	int ret;
-	uint32_t command_mode;
-	uint32_t address;
-	u32 pio[2];
-
-	/* [1] PIO */
-	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
-	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-
-	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(address)
-		| BF_GPMI_CTRL0_XFER_COUNT(len);
-	pio[1] = 0;
-	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
-				      DMA_TRANS_NONE, 0);
-	if (!desc)
-		return -EINVAL;
-
-	/* [2] send DMA request */
-	prepare_data_dma(this, buf, len, DMA_TO_DEVICE);
-	desc = dmaengine_prep_slave_sg(channel, &this->data_sgl,
-					1, DMA_MEM_TO_DEV,
-					MXS_DMA_CTRL_WAIT4END);
-	if (!desc)
-		return -EINVAL;
-
-	/* [3] submit the DMA */
-	ret = start_dma_without_bch_irq(this, desc);
-
-	dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE);
-
-	return ret;
-}
-
-static int gpmi_read_data(struct gpmi_nand_data *this, void *buf, int len)
-{
-	struct dma_async_tx_descriptor *desc;
-	struct dma_chan *channel = get_dma_chan(this);
-	int chip = this->current_chip;
-	int ret;
-	u32 pio[2];
-	bool direct;
-
-	/* [1] : send PIO */
-	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__READ)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
-		| BF_GPMI_CTRL0_XFER_COUNT(len);
-	pio[1] = 0;
-	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
-				      DMA_TRANS_NONE, 0);
-	if (!desc)
-		return -EINVAL;
-
-	/* [2] : send DMA request */
-	direct = prepare_data_dma(this, buf, len, DMA_FROM_DEVICE);
-	desc = dmaengine_prep_slave_sg(channel, &this->data_sgl,
-					1, DMA_DEV_TO_MEM,
-					MXS_DMA_CTRL_WAIT4END);
-	if (!desc)
-		return -EINVAL;
-
-	/* [3] : submit the DMA */
-
-	ret = start_dma_without_bch_irq(this, desc);
-
-	dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE);
-	if (!direct)
-		memcpy(buf, this->data_buffer_dma, len);
-
-	return ret;
-}
-
-static int gpmi_send_page(struct gpmi_nand_data *this, dma_addr_t payload,
-			  dma_addr_t auxiliary)
-{
-	struct bch_geometry *geo = &this->bch_geometry;
-	uint32_t command_mode;
-	uint32_t address;
-	uint32_t ecc_command;
-	uint32_t buffer_mask;
-	struct dma_async_tx_descriptor *desc;
-	struct dma_chan *channel = get_dma_chan(this);
-	int chip = this->current_chip;
-	u32 pio[6];
-
-	/* A DMA descriptor that does an ECC page read. */
-	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
-	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-	ecc_command  = BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE;
-	buffer_mask  = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE |
-				BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
-
-	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(address)
-		| BF_GPMI_CTRL0_XFER_COUNT(0);
-	pio[1] = 0;
-	pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
-		| BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
-		| BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
-	pio[3] = geo->page_size;
-	pio[4] = payload;
-	pio[5] = auxiliary;
-
-	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
-				      DMA_TRANS_NONE,
-				      MXS_DMA_CTRL_WAIT4END);
-	if (!desc)
-		return -EINVAL;
-
-	return start_dma_with_bch_irq(this, desc);
-}
-
-static int gpmi_read_page(struct gpmi_nand_data *this, dma_addr_t payload,
-			  dma_addr_t auxiliary)
-{
-	struct bch_geometry *geo = &this->bch_geometry;
-	uint32_t command_mode;
-	uint32_t address;
-	uint32_t ecc_command;
-	uint32_t buffer_mask;
-	struct dma_async_tx_descriptor *desc;
-	struct dma_chan *channel = get_dma_chan(this);
-	int chip = this->current_chip;
-	u32 pio[6];
-
-	/* [1] Wait for the chip to report ready. */
-	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
-	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-
-	pio[0] =  BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(address)
-		| BF_GPMI_CTRL0_XFER_COUNT(0);
-	pio[1] = 0;
-	desc = mxs_dmaengine_prep_pio(channel, pio, 2, DMA_TRANS_NONE, 0);
-	if (!desc)
-		return -EINVAL;
-
-	/* [2] Enable the BCH block and read. */
-	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__READ;
-	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-	ecc_command  = BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE;
-	buffer_mask  = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE
-			| BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
-
-	pio[0] =  BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(address)
-		| BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
-
-	pio[1] = 0;
-	pio[2] =  BM_GPMI_ECCCTRL_ENABLE_ECC
-		| BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
-		| BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
-	pio[3] = geo->page_size;
-	pio[4] = payload;
-	pio[5] = auxiliary;
-	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
-				      DMA_TRANS_NONE,
-				      MXS_DMA_CTRL_WAIT4END);
-	if (!desc)
-		return -EINVAL;
-
-	/* [3] Disable the BCH block */
-	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
-	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-
-	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
-		| BM_GPMI_CTRL0_WORD_LENGTH
-		| BF_GPMI_CTRL0_CS(chip, this)
-		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
-		| BF_GPMI_CTRL0_ADDRESS(address)
-		| BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
-	pio[1] = 0;
-	pio[2] = 0; /* clear GPMI_HW_GPMI_ECCCTRL, disable the BCH. */
-	desc = mxs_dmaengine_prep_pio(channel, pio, 3, DMA_TRANS_NONE,
-				      MXS_DMA_CTRL_WAIT4END);
-	if (!desc)
-		return -EINVAL;
-
-	/* [4] submit the DMA */
-	return start_dma_with_bch_irq(this, desc);
-}
-
 /**
  * gpmi_copy_bits - copy bits from one memory region to another
  * @dst: destination buffer
@@ -1568,67 +1227,20 @@ static void release_resources(struct gpmi_nand_data *this)
 	release_dma_channels(this);
 }
 
-static int send_page_prepare(struct gpmi_nand_data *this,
-			const void *source, unsigned length,
-			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
-			const void **use_virt, dma_addr_t *use_phys)
-{
-	struct device *dev = this->dev;
-
-	if (virt_addr_valid(source)) {
-		dma_addr_t source_phys;
-
-		source_phys = dma_map_single(dev, (void *)source, length,
-						DMA_TO_DEVICE);
-		if (dma_mapping_error(dev, source_phys)) {
-			if (alt_size < length) {
-				dev_err(dev, "Alternate buffer is too small\n");
-				return -ENOMEM;
-			}
-			goto map_failed;
-		}
-		*use_virt = source;
-		*use_phys = source_phys;
-		return 0;
-	}
-map_failed:
-	/*
-	 * Copy the content of the source buffer into the alternate
-	 * buffer and set up the return values accordingly.
-	 */
-	memcpy(alt_virt, source, length);
-
-	*use_virt = alt_virt;
-	*use_phys = alt_phys;
-	return 0;
-}
-
-static void send_page_end(struct gpmi_nand_data *this,
-			const void *source, unsigned length,
-			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
-			const void *used_virt, dma_addr_t used_phys)
-{
-	struct device *dev = this->dev;
-	if (used_virt == source)
-		dma_unmap_single(dev, used_phys, length, DMA_TO_DEVICE);
-}
-
 static void gpmi_free_dma_buffer(struct gpmi_nand_data *this)
 {
 	struct device *dev = this->dev;
+	struct bch_geometry *geo = &this->bch_geometry;
 
-	if (this->payload_virt && virt_addr_valid(this->payload_virt))
-		dma_free_coherent(dev, this->page_buffer_size,
-					this->payload_virt,
-					this->payload_phys);
-	kfree(this->cmd_buffer);
+	if (this->auxiliary_virt && virt_addr_valid(this->auxiliary_virt))
+		dma_free_coherent(dev, geo->auxiliary_size,
+					this->auxiliary_virt,
+					this->auxiliary_phys);
 	kfree(this->data_buffer_dma);
 	kfree(this->raw_buffer);
 
-	this->cmd_buffer	= NULL;
 	this->data_buffer_dma	= NULL;
 	this->raw_buffer	= NULL;
-	this->page_buffer_size	=  0;
 }
 
 /* Allocate the DMA buffers */
@@ -1638,11 +1250,6 @@ static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this)
 	struct device *dev = this->dev;
 	struct mtd_info *mtd = nand_to_mtd(&this->nand);
 
-	/* [1] Allocate a command buffer. PAGE_SIZE is enough. */
-	this->cmd_buffer = kzalloc(PAGE_SIZE, GFP_DMA | GFP_KERNEL);
-	if (this->cmd_buffer == NULL)
-		goto error_alloc;
-
 	/*
 	 * [2] Allocate a read/write data buffer.
 	 *     The gpmi_alloc_dma_buffer can be called twice.
@@ -1656,27 +1263,15 @@ static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this)
 	if (this->data_buffer_dma == NULL)
 		goto error_alloc;
 
-	/*
-	 * [3] Allocate the page buffer.
-	 *
-	 * Both the payload buffer and the auxiliary buffer must appear on
-	 * 32-bit boundaries. We presume the size of the payload buffer is a
-	 * power of two and is much larger than four, which guarantees the
-	 * auxiliary buffer will appear on a 32-bit boundary.
-	 */
-	this->page_buffer_size = geo->payload_size + geo->auxiliary_size;
-	this->payload_virt = dma_alloc_coherent(dev, this->page_buffer_size,
-					&this->payload_phys, GFP_DMA);
-	if (!this->payload_virt)
+	this->auxiliary_virt = dma_alloc_coherent(dev, geo->auxiliary_size,
+					&this->auxiliary_phys, GFP_DMA);
+	if (!this->auxiliary_virt)
 		goto error_alloc;
 
-	this->raw_buffer = kzalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL);
+	this->raw_buffer = kzalloc((mtd->writesize ?: PAGE_SIZE) + mtd->oobsize, GFP_KERNEL);
 	if (!this->raw_buffer)
 		goto error_alloc;
 
-	/* Slice up the page buffer. */
-	this->auxiliary_virt = this->payload_virt + geo->payload_size;
-	this->auxiliary_phys = this->payload_phys + geo->payload_size;
 	return 0;
 
 error_alloc:
@@ -1684,105 +1279,6 @@ error_alloc:
 	return -ENOMEM;
 }
 
-static void gpmi_cmd_ctrl(struct nand_chip *chip, int data, unsigned int ctrl)
-{
-	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-	int ret;
-
-	/*
-	 * Every operation begins with a command byte and a series of zero or
-	 * more address bytes. These are distinguished by either the Address
-	 * Latch Enable (ALE) or Command Latch Enable (CLE) signals being
-	 * asserted. When MTD is ready to execute the command, it will deassert
-	 * both latch enables.
-	 *
-	 * Rather than run a separate DMA operation for every single byte, we
-	 * queue them up and run a single DMA operation for the entire series
-	 * of command and data bytes. NAND_CMD_NONE means the END of the queue.
-	 */
-	if ((ctrl & (NAND_ALE | NAND_CLE))) {
-		if (data != NAND_CMD_NONE)
-			this->cmd_buffer[this->command_length++] = data;
-		return;
-	}
-
-	if (!this->command_length)
-		return;
-
-	ret = gpmi_send_command(this);
-	if (ret)
-		dev_err(this->dev, "Chip: %u, Error %d\n",
-			this->current_chip, ret);
-
-	this->command_length = 0;
-}
-
-static int gpmi_dev_ready(struct nand_chip *chip)
-{
-	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-
-	return gpmi_is_ready(this, this->current_chip);
-}
-
-static void gpmi_select_chip(struct nand_chip *chip, int chipnr)
-{
-	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-	int ret;
-
-	/*
-	 * For power consumption matters, disable/enable the clock each time a
-	 * die is selected/unselected.
-	 */
-	if (this->current_chip < 0 && chipnr >= 0) {
-		ret = pm_runtime_get_sync(this->dev);
-		if (ret < 0)
-			dev_err(this->dev, "Failed to enable the clock\n");
-	} else if (this->current_chip >= 0 && chipnr < 0) {
-		pm_runtime_mark_last_busy(this->dev);
-		pm_runtime_put_autosuspend(this->dev);
-	}
-
-	/*
-	 * This driver currently supports only one NAND chip. Plus, dies share
-	 * the same configuration. So once timings have been applied on the
-	 * controller side, they will not change anymore. When the time will
-	 * come, the check on must_apply_timings will have to be dropped.
-	 */
-	if (chipnr >= 0 && this->hw.must_apply_timings) {
-		this->hw.must_apply_timings = false;
-		gpmi_nfc_apply_timings(this);
-	}
-
-	this->current_chip = chipnr;
-}
-
-static void gpmi_read_buf(struct nand_chip *chip, uint8_t *buf, int len)
-{
-	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-
-	dev_dbg(this->dev, "len is %d\n", len);
-
-	gpmi_read_data(this, buf, len);
-}
-
-static void gpmi_write_buf(struct nand_chip *chip, const uint8_t *buf, int len)
-{
-	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-
-	dev_dbg(this->dev, "len is %d\n", len);
-
-	gpmi_send_data(this, buf, len);
-}
-
-static uint8_t gpmi_read_byte(struct nand_chip *chip)
-{
-	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-	uint8_t *buf = this->data_buffer_dma;
-
-	gpmi_read_buf(chip, buf, 1);
-	return buf[0];
-}
-
 /*
  * Handles block mark swapping.
  * It can be called in swapping the block mark, or swapping it back,
@@ -1831,50 +1327,20 @@ static void block_mark_swapping(struct gpmi_nand_data *this,
 	p[1] = (p[1] & mask) | (from_oob >> (8 - bit));
 }
 
-static int gpmi_ecc_read_page_data(struct nand_chip *chip, uint8_t *buf)
+static int gpmi_count_bitflips(struct nand_chip *chip, void *buf, int first,
+			       int last, int meta)
 {
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
 	struct bch_geometry *nfc_geo = &this->bch_geometry;
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	dma_addr_t    payload_phys;
-	unsigned int  i;
+	int i;
 	unsigned char *status;
-	unsigned int  max_bitflips = 0;
-	int           ret;
-	bool          direct = false;
-
-	payload_phys = this->payload_phys;
-
-	if (virt_addr_valid(buf)) {
-		dma_addr_t dest_phys;
-
-		dest_phys = dma_map_single(this->dev, buf, nfc_geo->payload_size,
-					   DMA_FROM_DEVICE);
-		if (!dma_mapping_error(this->dev, dest_phys)) {
-			payload_phys = dest_phys;
-			direct = true;
-		}
-	}
-
-	/* go! */
-	ret = gpmi_read_page(this, payload_phys, this->auxiliary_phys);
-
-	if (direct)
-		dma_unmap_single(this->dev, payload_phys, nfc_geo->payload_size,
-				 DMA_FROM_DEVICE);
-
-	if (ret) {
-		dev_err(this->dev, "Error in ECC-based read: %d\n", ret);
-		return ret;
-	}
+	unsigned int max_bitflips = 0;
 
 	/* Loop over status bytes, accumulating ECC status. */
-	status = this->auxiliary_virt + nfc_geo->auxiliary_status_offset;
+	status = this->auxiliary_virt + ALIGN(meta, 4);
 
-	if (!direct)
-		memcpy(buf, this->payload_virt, nfc_geo->payload_size);
-
-	for (i = 0; i < nfc_geo->ecc_chunk_count; i++, status++) {
+	for (i = first; i < last; i++, status++) {
 		if ((*status == STATUS_GOOD) || (*status == STATUS_ERASED))
 			continue;
 
@@ -1954,25 +1420,53 @@ static int gpmi_ecc_read_page_data(struct nand_chip *chip, uint8_t *buf)
 		max_bitflips = max_t(unsigned int, max_bitflips, *status);
 	}
 
-	/* handle the block mark swapping */
-	block_mark_swapping(this, buf, this->auxiliary_virt);
-
 	return max_bitflips;
 }
 
+static void gpmi_bch_layout_std(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	unsigned int ecc_strength = geo->ecc_strength >> 1;
+	unsigned int gf_len = geo->gf_len;
+	unsigned int block_size = block_size = geo->ecc_chunk_size;
+
+	this->bch_flashlayout0 =
+		BF_BCH_FLASH0LAYOUT0_NBLOCKS(geo->ecc_chunk_count - 1) |
+		BF_BCH_FLASH0LAYOUT0_META_SIZE(geo->metadata_size) |
+		BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this) |
+		BF_BCH_FLASH0LAYOUT0_GF(gf_len, this) |
+		BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this);
+
+	this->bch_flashlayout1 =
+		BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(geo->page_size) |
+		BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this) |
+		BF_BCH_FLASH0LAYOUT1_GF(gf_len, this) |
+		BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this);
+}
+
 static int gpmi_ecc_read_page(struct nand_chip *chip, uint8_t *buf,
 			      int oob_required, int page)
 {
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct bch_geometry *geo = &this->bch_geometry;
+	unsigned int max_bitflips;
 	int ret;
 
-	nand_read_page_op(chip, page, 0, NULL, 0);
+	gpmi_bch_layout_std(this);
+	this->bch = true;
 
-	ret = gpmi_ecc_read_page_data(chip, buf);
-	if (ret < 0)
+	ret = nand_read_page_op(chip, page, 0, buf, geo->page_size);
+	if (ret)
 		return ret;
 
+	max_bitflips = gpmi_count_bitflips(chip, buf, 0,
+					   geo->ecc_chunk_count,
+					   geo->auxiliary_status_offset);
+
+	/* handle the block mark swapping */
+	block_mark_swapping(this, buf, this->auxiliary_virt);
+
 	if (oob_required) {
 		/*
 		 * It's time to deliver the OOB bytes. See gpmi_ecc_read_oob()
@@ -1988,7 +1482,7 @@ static int gpmi_ecc_read_page(struct nand_chip *chip, uint8_t *buf,
 		chip->oob_poi[0] = ((uint8_t *)this->auxiliary_virt)[0];
 	}
 
-	return ret;
+	return max_bitflips;
 }
 
 /* Fake a virtual small page for the subpage read */
@@ -1996,17 +1490,15 @@ static int gpmi_ecc_read_subpage(struct nand_chip *chip, uint32_t offs,
 				 uint32_t len, uint8_t *buf, int page)
 {
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
-	void __iomem *bch_regs = this->resources.bch_regs;
-	struct bch_geometry old_geo = this->bch_geometry;
 	struct bch_geometry *geo = &this->bch_geometry;
 	int size = chip->ecc.size; /* ECC chunk size */
 	int meta, n, page_size;
-	u32 r1_old, r2_old, r1_new, r2_new;
 	unsigned int max_bitflips;
+	unsigned int ecc_strength;
 	int first, last, marker_pos;
 	int ecc_parity_size;
 	int col = 0;
-	int old_swap_block_mark = this->swap_block_mark;
+	int ret;
 
 	/* The size of ECC parity */
 	ecc_parity_size = geo->gf_len * geo->ecc_strength / 8;
@@ -2039,43 +1531,33 @@ static int gpmi_ecc_read_subpage(struct nand_chip *chip, uint32_t offs,
 		buf = buf + first * size;
 	}
 
-	nand_read_page_op(chip, page, col, NULL, 0);
+	ecc_parity_size = geo->gf_len * geo->ecc_strength / 8;
 
-	/* Save the old environment */
-	r1_old = r1_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT0);
-	r2_old = r2_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT1);
-
-	/* change the BCH registers and bch_geometry{} */
 	n = last - first + 1;
 	page_size = meta + (size + ecc_parity_size) * n;
+	ecc_strength = geo->ecc_strength >> 1;
 
-	r1_new &= ~(BM_BCH_FLASH0LAYOUT0_NBLOCKS |
-			BM_BCH_FLASH0LAYOUT0_META_SIZE);
-	r1_new |= BF_BCH_FLASH0LAYOUT0_NBLOCKS(n - 1)
-			| BF_BCH_FLASH0LAYOUT0_META_SIZE(meta);
-	writel(r1_new, bch_regs + HW_BCH_FLASH0LAYOUT0);
+	this->bch_flashlayout0 = BF_BCH_FLASH0LAYOUT0_NBLOCKS(n - 1) |
+		BF_BCH_FLASH0LAYOUT0_META_SIZE(meta) |
+		BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this) |
+		BF_BCH_FLASH0LAYOUT0_GF(geo->gf_len, this) |
+		BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(geo->ecc_chunk_size, this);
 
-	r2_new &= ~BM_BCH_FLASH0LAYOUT1_PAGE_SIZE;
-	r2_new |= BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size);
-	writel(r2_new, bch_regs + HW_BCH_FLASH0LAYOUT1);
+	this->bch_flashlayout1 = BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size) |
+		BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this) |
+		BF_BCH_FLASH0LAYOUT1_GF(geo->gf_len, this) |
+		BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(geo->ecc_chunk_size, this);
 
-	geo->ecc_chunk_count = n;
-	geo->payload_size = n * size;
-	geo->page_size = page_size;
-	geo->auxiliary_status_offset = ALIGN(meta, 4);
+	this->bch = true;
+
+	ret = nand_read_page_op(chip, page, col, buf, page_size);
+	if (ret)
+		return ret;
 
 	dev_dbg(this->dev, "page:%d(%d:%d)%d, chunk:(%d:%d), BCH PG size:%d\n",
 		page, offs, len, col, first, n, page_size);
 
-	/* Read the subpage now */
-	this->swap_block_mark = false;
-	max_bitflips = gpmi_ecc_read_page_data(chip, buf);
-
-	/* Restore */
-	writel(r1_old, bch_regs + HW_BCH_FLASH0LAYOUT0);
-	writel(r2_old, bch_regs + HW_BCH_FLASH0LAYOUT1);
-	this->bch_geometry = old_geo;
-	this->swap_block_mark = old_swap_block_mark;
+	max_bitflips = gpmi_count_bitflips(chip, buf, first, last, meta);
 
 	return max_bitflips;
 }
@@ -2086,81 +1568,29 @@ static int gpmi_ecc_write_page(struct nand_chip *chip, const uint8_t *buf,
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
 	struct bch_geometry *nfc_geo = &this->bch_geometry;
-	const void *payload_virt;
-	dma_addr_t payload_phys;
-	const void *auxiliary_virt;
-	dma_addr_t auxiliary_phys;
-	int        ret;
+	int ret;
 
 	dev_dbg(this->dev, "ecc write page.\n");
 
-	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
+	gpmi_bch_layout_std(this);
+	this->bch = true;
+
+	memcpy(this->auxiliary_virt, chip->oob_poi, nfc_geo->auxiliary_size);
 
 	if (this->swap_block_mark) {
 		/*
-		 * If control arrives here, we're doing block mark swapping.
-		 * Since we can't modify the caller's buffers, we must copy them
-		 * into our own.
+		 * When doing bad block marker swapping we must always copy the
+		 * input buffer as we can't modify the const buffer.
 		 */
-		memcpy(this->payload_virt, buf, mtd->writesize);
-		payload_virt = this->payload_virt;
-		payload_phys = this->payload_phys;
-
-		memcpy(this->auxiliary_virt, chip->oob_poi,
-				nfc_geo->auxiliary_size);
-		auxiliary_virt = this->auxiliary_virt;
-		auxiliary_phys = this->auxiliary_phys;
-
-		/* Handle block mark swapping. */
-		block_mark_swapping(this,
-				(void *)payload_virt, (void *)auxiliary_virt);
-	} else {
-		/*
-		 * If control arrives here, we're not doing block mark swapping,
-		 * so we can to try and use the caller's buffers.
-		 */
-		ret = send_page_prepare(this,
-				buf, mtd->writesize,
-				this->payload_virt, this->payload_phys,
-				nfc_geo->payload_size,
-				&payload_virt, &payload_phys);
-		if (ret) {
-			dev_err(this->dev, "Inadequate payload DMA buffer\n");
-			return 0;
-		}
-
-		ret = send_page_prepare(this,
-				chip->oob_poi, mtd->oobsize,
-				this->auxiliary_virt, this->auxiliary_phys,
-				nfc_geo->auxiliary_size,
-				&auxiliary_virt, &auxiliary_phys);
-		if (ret) {
-			dev_err(this->dev, "Inadequate auxiliary DMA buffer\n");
-			goto exit_auxiliary;
-		}
+		memcpy(this->data_buffer_dma, buf, mtd->writesize);
+		buf = this->data_buffer_dma;
+		block_mark_swapping(this, this->data_buffer_dma,
+				    this->auxiliary_virt);
 	}
 
-	/* Ask the NFC. */
-	ret = gpmi_send_page(this, payload_phys, auxiliary_phys);
-	if (ret)
-		dev_err(this->dev, "Error in ECC-based write: %d\n", ret);
+	ret = nand_prog_page_op(chip, page, 0, buf, nfc_geo->page_size);
 
-	if (!this->swap_block_mark) {
-		send_page_end(this, chip->oob_poi, mtd->oobsize,
-				this->auxiliary_virt, this->auxiliary_phys,
-				nfc_geo->auxiliary_size,
-				auxiliary_virt, auxiliary_phys);
-exit_auxiliary:
-		send_page_end(this, buf, mtd->writesize,
-				this->payload_virt, this->payload_phys,
-				nfc_geo->payload_size,
-				payload_virt, payload_phys);
-	}
-
-	if (ret)
-		return ret;
-
-	return nand_prog_page_end_op(chip);
+	return ret;
 }
 
 /*
@@ -2229,7 +1659,6 @@ static int gpmi_ecc_read_oob(struct nand_chip *chip, int page)
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
 	int ret;
 
-	dev_dbg(this->dev, "page number is %d\n", page);
 	/* clear the OOB buffer */
 	memset(chip->oob_poi, ~0, mtd->oobsize);
 
@@ -2297,9 +1726,12 @@ static int gpmi_ecc_read_page_raw(struct nand_chip *chip, uint8_t *buf,
 	size_t oob_byte_off;
 	uint8_t *oob = chip->oob_poi;
 	int step;
+	int ret;
 
-	nand_read_page_op(chip, page, 0, tmp_buf,
-			  mtd->writesize + mtd->oobsize);
+	ret = nand_read_page_op(chip, page, 0, tmp_buf,
+				mtd->writesize + mtd->oobsize);
+	if (ret)
+		return ret;
 
 	/*
 	 * If required, swap the bad block marker and the data stored in the
@@ -2789,9 +2221,330 @@ static int gpmi_nand_attach_chip(struct nand_chip *chip)
 	return 0;
 }
 
+static struct gpmi_transfer *get_next_transfer(struct gpmi_nand_data *this)
+{
+	struct gpmi_transfer *transfer = &this->transfers[this->ntransfers];
+
+	this->ntransfers++;
+
+	if (this->ntransfers == GPMI_MAX_TRANSFERS)
+		return NULL;
+
+	return transfer;
+}
+
+static struct dma_async_tx_descriptor *gpmi_chain_command(
+	struct gpmi_nand_data *this, u8 cmd, const u8 *addr, int naddr)
+{
+	struct dma_chan *channel = get_dma_chan(this);
+	struct dma_async_tx_descriptor *desc;
+	struct gpmi_transfer *transfer;
+	int chip = this->nand.cur_cs;
+	u32 pio[3];
+
+	/* [1] send out the PIO words */
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_CLE)
+		| BM_GPMI_CTRL0_ADDRESS_INCREMENT
+		| BF_GPMI_CTRL0_XFER_COUNT(naddr + 1);
+	pio[1] = 0;
+	pio[2] = 0;
+	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
+				      DMA_TRANS_NONE, 0);
+	if (!desc)
+		return NULL;
+
+	transfer = get_next_transfer(this);
+	if (!transfer)
+		return NULL;
+
+	transfer->cmdbuf[0] = cmd;
+	if (naddr)
+		memcpy(&transfer->cmdbuf[1], addr, naddr);
+
+	sg_init_one(&transfer->sgl, transfer->cmdbuf, naddr + 1);
+	dma_map_sg(this->dev, &transfer->sgl, 1, DMA_TO_DEVICE);
+
+	transfer->direction = DMA_TO_DEVICE;
+
+	desc = dmaengine_prep_slave_sg(channel, &transfer->sgl, 1, DMA_MEM_TO_DEV,
+				       MXS_DMA_CTRL_WAIT4END);
+	return desc;
+}
+
+static struct dma_async_tx_descriptor *gpmi_chain_wait_ready(
+	struct gpmi_nand_data *this)
+{
+	struct dma_chan *channel = get_dma_chan(this);
+	u32 pio[2];
+
+	pio[0] =  BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(this->nand.cur_cs, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
+		| BF_GPMI_CTRL0_XFER_COUNT(0);
+	pio[1] = 0;
+
+	return mxs_dmaengine_prep_pio(channel, pio, 2, DMA_TRANS_NONE,
+				MXS_DMA_CTRL_WAIT4END | MXS_DMA_CTRL_WAIT4RDY);
+}
+
+static struct dma_async_tx_descriptor *gpmi_chain_data_read(
+	struct gpmi_nand_data *this, void *buf, int raw_len, bool *direct)
+{
+	struct dma_async_tx_descriptor *desc;
+	struct dma_chan *channel = get_dma_chan(this);
+	struct gpmi_transfer *transfer;
+	u32 pio[6] = {};
+
+	transfer = get_next_transfer(this);
+	if (!transfer)
+		return NULL;
+
+	transfer->direction = DMA_FROM_DEVICE;
+
+	*direct = prepare_data_dma(this, buf, raw_len, &transfer->sgl,
+				   DMA_FROM_DEVICE);
+
+	pio[0] =  BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__READ)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(this->nand.cur_cs, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
+		| BF_GPMI_CTRL0_XFER_COUNT(raw_len);
+
+	if (this->bch) {
+		pio[2] =  BM_GPMI_ECCCTRL_ENABLE_ECC
+			| BF_GPMI_ECCCTRL_ECC_CMD(BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE)
+			| BF_GPMI_ECCCTRL_BUFFER_MASK(BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE
+				| BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY);
+		pio[3] = raw_len;
+		pio[4] = transfer->sgl.dma_address;
+		pio[5] = this->auxiliary_phys;
+	}
+
+	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
+				      DMA_TRANS_NONE, 0);
+	if (!desc)
+		return NULL;
+
+	if (!this->bch)
+		desc = dmaengine_prep_slave_sg(channel, &transfer->sgl, 1,
+					     DMA_DEV_TO_MEM,
+					     MXS_DMA_CTRL_WAIT4END);
+
+	return desc;
+}
+
+static struct dma_async_tx_descriptor *gpmi_chain_data_write(
+	struct gpmi_nand_data *this, const void *buf, int raw_len)
+{
+	struct dma_chan *channel = get_dma_chan(this);
+	struct dma_async_tx_descriptor *desc;
+	struct gpmi_transfer *transfer;
+	u32 pio[6] = {};
+
+	transfer = get_next_transfer(this);
+	if (!transfer)
+		return NULL;
+
+	transfer->direction = DMA_TO_DEVICE;
+
+	prepare_data_dma(this, buf, raw_len, &transfer->sgl, DMA_TO_DEVICE);
+
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(this->nand.cur_cs, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
+		| BF_GPMI_CTRL0_XFER_COUNT(raw_len);
+
+	if (this->bch) {
+		pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
+			| BF_GPMI_ECCCTRL_ECC_CMD(BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE)
+			| BF_GPMI_ECCCTRL_BUFFER_MASK(BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE |
+					BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY);
+		pio[3] = raw_len;
+		pio[4] = transfer->sgl.dma_address;
+		pio[5] = this->auxiliary_phys;
+	}
+
+	desc = mxs_dmaengine_prep_pio(channel, pio, ARRAY_SIZE(pio),
+				      DMA_TRANS_NONE,
+				      (this->bch ? MXS_DMA_CTRL_WAIT4END : 0));
+	if (!desc)
+		return NULL;
+
+	if (!this->bch)
+		desc = dmaengine_prep_slave_sg(channel, &transfer->sgl, 1,
+					       DMA_MEM_TO_DEV,
+					       MXS_DMA_CTRL_WAIT4END);
+
+	return desc;
+}
+
+static int gpmi_nfc_exec_op(struct nand_chip *chip,
+			     const struct nand_operation *op,
+			     bool check_only)
+{
+	const struct nand_op_instr *instr;
+	struct gpmi_nand_data *this = nand_get_controller_data(chip);
+	struct dma_async_tx_descriptor *desc = NULL;
+	int i, ret, buf_len = 0, nbufs = 0;
+	u8 cmd = 0;
+	void *buf_read = NULL;
+	const void *buf_write = NULL;
+	bool direct = false;
+	struct completion *completion;
+	unsigned long to;
+
+	this->ntransfers = 0;
+	for (i = 0; i < GPMI_MAX_TRANSFERS; i++)
+		this->transfers[i].direction = DMA_NONE;
+
+	ret = pm_runtime_get_sync(this->dev);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * This driver currently supports only one NAND chip. Plus, dies share
+	 * the same configuration. So once timings have been applied on the
+	 * controller side, they will not change anymore. When the time will
+	 * come, the check on must_apply_timings will have to be dropped.
+	 */
+	if (this->hw.must_apply_timings) {
+		this->hw.must_apply_timings = false;
+		gpmi_nfc_apply_timings(this);
+	}
+
+	dev_dbg(this->dev, "%s: %d instructions\n", __func__, op->ninstrs);
+
+	for (i = 0; i < op->ninstrs; i++) {
+		instr = &op->instrs[i];
+
+		nand_op_trace("  ", instr);
+
+		switch (instr->type) {
+		case NAND_OP_WAITRDY_INSTR:
+			desc = gpmi_chain_wait_ready(this);
+			break;
+		case NAND_OP_CMD_INSTR:
+			cmd = instr->ctx.cmd.opcode;
+
+			/*
+			 * When this command has an address cycle chain it
+			 * together with the address cycle
+			 */
+			if (i + 1 != op->ninstrs &&
+			    op->instrs[i + 1].type == NAND_OP_ADDR_INSTR)
+				continue;
+
+			desc = gpmi_chain_command(this, cmd, NULL, 0);
+
+			break;
+		case NAND_OP_ADDR_INSTR:
+			desc = gpmi_chain_command(this, cmd, instr->ctx.addr.addrs,
+						  instr->ctx.addr.naddrs);
+			break;
+		case NAND_OP_DATA_OUT_INSTR:
+			buf_write = instr->ctx.data.buf.out;
+			buf_len = instr->ctx.data.len;
+			nbufs++;
+
+			desc = gpmi_chain_data_write(this, buf_write, buf_len);
+
+			break;
+		case NAND_OP_DATA_IN_INSTR:
+			if (!instr->ctx.data.len)
+				break;
+			buf_read = instr->ctx.data.buf.in;
+			buf_len = instr->ctx.data.len;
+			nbufs++;
+
+			desc = gpmi_chain_data_read(this, buf_read, buf_len,
+						   &direct);
+			break;
+		}
+
+		if (!desc) {
+			ret = -ENXIO;
+			goto unmap;
+		}
+	}
+
+	dev_dbg(this->dev, "%s setup done\n", __func__);
+
+	if (nbufs > 1) {
+		dev_err(this->dev, "Multiple data instructions not supported\n");
+		ret = -EINVAL;
+		goto unmap;
+	}
+
+	if (this->bch) {
+		writel(this->bch_flashlayout0,
+		       this->resources.bch_regs + HW_BCH_FLASH0LAYOUT0);
+		writel(this->bch_flashlayout1,
+		       this->resources.bch_regs + HW_BCH_FLASH0LAYOUT1);
+	}
+
+	if (this->bch && buf_read) {
+		writel(BM_BCH_CTRL_COMPLETE_IRQ_EN,
+		       this->resources.bch_regs + HW_BCH_CTRL_SET);
+		completion = &this->bch_done;
+	} else {
+		desc->callback = dma_irq_callback;
+		desc->callback_param = this;
+		completion = &this->dma_done;
+	}
+
+	init_completion(completion);
+
+	dmaengine_submit(desc);
+	dma_async_issue_pending(get_dma_chan(this));
+
+	to = wait_for_completion_timeout(completion, msecs_to_jiffies(1000));
+	if (!to) {
+		dev_err(this->dev, "DMA timeout, last DMA\n");
+		gpmi_dump_info(this);
+		ret = -ETIMEDOUT;
+		goto unmap;
+	}
+
+	writel(BM_BCH_CTRL_COMPLETE_IRQ_EN,
+	       this->resources.bch_regs + HW_BCH_CTRL_CLR);
+	gpmi_clear_bch(this);
+
+	ret = 0;
+
+unmap:
+	for (i = 0; i < this->ntransfers; i++) {
+		struct gpmi_transfer *transfer = &this->transfers[i];
+
+		if (transfer->direction != DMA_NONE)
+			dma_unmap_sg(this->dev, &transfer->sgl, 1,
+				     transfer->direction);
+	}
+
+	if (!ret && buf_read && !direct)
+		memcpy(buf_read, this->data_buffer_dma,
+		       gpmi_raw_len_to_len(this, buf_len));
+
+	this->bch = false;
+
+	pm_runtime_mark_last_busy(this->dev);
+	pm_runtime_put_autosuspend(this->dev);
+
+	return ret;
+}
+
 static const struct nand_controller_ops gpmi_nand_controller_ops = {
 	.attach_chip = gpmi_nand_attach_chip,
 	.setup_data_interface = gpmi_setup_data_interface,
+	.exec_op = gpmi_nfc_exec_op,
 };
 
 static int gpmi_nand_init(struct gpmi_nand_data *this)
@@ -2800,9 +2553,6 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 	struct mtd_info  *mtd = nand_to_mtd(chip);
 	int ret;
 
-	/* init current chip */
-	this->current_chip	= -1;
-
 	/* init the MTD data structures */
 	mtd->name		= "gpmi-nand";
 	mtd->dev.parent		= this->dev;
@@ -2810,14 +2560,8 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 	/* init the nand_chip{}, we don't support a 16-bit NAND Flash bus. */
 	nand_set_controller_data(chip, this);
 	nand_set_flash_node(chip, this->pdev->dev.of_node);
-	chip->legacy.select_chip	= gpmi_select_chip;
-	chip->legacy.cmd_ctrl	= gpmi_cmd_ctrl;
-	chip->legacy.dev_ready	= gpmi_dev_ready;
-	chip->legacy.read_byte	= gpmi_read_byte;
-	chip->legacy.read_buf	= gpmi_read_buf;
-	chip->legacy.write_buf	= gpmi_write_buf;
-	chip->badblock_pattern	= &gpmi_bbt_descr;
 	chip->legacy.block_markbad = gpmi_block_markbad;
+	chip->badblock_pattern	= &gpmi_bbt_descr;
 	chip->options		|= NAND_NO_SUBPAGE_WRITE;
 
 	/* Set up swap_block_mark, must be set before the gpmi_set_geometry() */
@@ -2833,7 +2577,10 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
-	chip->legacy.dummy_controller.ops = &gpmi_nand_controller_ops;
+	nand_controller_init(&this->base);
+	this->base.ops = &gpmi_nand_controller_ops;
+	chip->controller = &this->base;
+
 	ret = nand_scan(chip, GPMI_IS_MX6(this) ? 2 : 1);
 	if (ret)
 		goto err_out;
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
index 51a070da84ed..fdc5ed7de083 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
@@ -103,6 +103,14 @@ struct gpmi_nfc_hardware_timing {
 	u32 ctrl1n;
 };
 
+#define GPMI_MAX_TRANSFERS	8
+
+struct gpmi_transfer {
+	u8 cmdbuf[8];
+	struct scatterlist sgl;
+	enum dma_data_direction direction;
+};
+
 struct gpmi_nand_data {
 	/* Devdata */
 	const struct gpmi_devdata *devdata;
@@ -126,23 +134,18 @@ struct gpmi_nand_data {
 	struct boot_rom_geometry rom_geometry;
 
 	/* MTD / NAND */
+	struct nand_controller	base;
 	struct nand_chip	nand;
 
-	/* General-use Variables */
-	int			current_chip;
-	unsigned int		command_length;
+	struct gpmi_transfer	transfers[GPMI_MAX_TRANSFERS];
+	int			ntransfers;
 
-	struct scatterlist	cmd_sgl;
-	char			*cmd_buffer;
+	bool			bch;
+	uint32_t		bch_flashlayout0;
+	uint32_t		bch_flashlayout1;
 
-	struct scatterlist	data_sgl;
 	char			*data_buffer_dma;
 
-	unsigned int		page_buffer_size;
-
-	void			*payload_virt;
-	dma_addr_t		payload_phys;
-
 	void			*auxiliary_virt;
 	dma_addr_t		auxiliary_phys;
 
diff --git a/include/linux/dma/mxs-dma.h b/include/linux/dma/mxs-dma.h
index 4a33f2c8a682..069d9f5a609e 100644
--- a/include/linux/dma/mxs-dma.h
+++ b/include/linux/dma/mxs-dma.h
@@ -5,6 +5,7 @@
 #include <linux/dmaengine.h>
 
 #define MXS_DMA_CTRL_WAIT4END	BIT(31)
+#define MXS_DMA_CTRL_WAIT4RDY	BIT(30)
 
 /*
  * The mxs dmaengine can do PIO transfers. We pass a pointer to the PIO words