Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-11-11 14:42:24 +00:00
Code Issues Packages Projects Releases Wiki Activity

avr32: Add support for ATSTK1006

Browse Source 
The ATSTK1006 is basically an upgraded version of ATSTK1002 with
128 MiB SDRAM and 256 MiB NAND flash on board.

Otherwise, the board is very similar to the ATSTK1002, so it uses the
same board support file.

Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This commit is contained in:
Håvard Skinnemoen 2008-06-06 18:04:58 +02:00 committed by David Woodhouse
parent 984290ded4
commit e150d6e725
3 changed files with 81 additions and 2 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

4
arch/avr32/boards/atstk1000/Kconfig
View File

@ -18,6 +18,10 @@ config BOARD_ATSTK1004
bool "ATSTK1004"
select CPU_AT32AP7002
config BOARD_ATSTK1006
bool "ATSTK1006"
select CPU_AT32AP7000
endchoice

1
arch/avr32/boards/atstk1000/Makefile
View File

@ -2,3 +2,4 @@ obj-y += setup.o flash.o
obj-$(CONFIG_BOARD_ATSTK1002) += atstk1002.o
obj-$(CONFIG_BOARD_ATSTK1003) += atstk1003.o
obj-$(CONFIG_BOARD_ATSTK1004) += atstk1004.o
obj-$(CONFIG_BOARD_ATSTK1006) += atstk1002.o

78
arch/avr32/boards/atstk1000/atstk1002.c
View File

@ -1,7 +1,7 @@
/*
* ATSTK1002 daughterboard-specific init code
* ATSTK1002/ATSTK1006 daughterboard-specific init code
*
* Copyright (C) 2005-2006 Atmel Corporation
* Copyright (C) 2005-2007 Atmel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@ -29,6 +29,74 @@
#include "atstk1000.h"
/*
* The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both
* have the AT32AP7000 chip on board; the difference is that the
* STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on
* the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has
* none.)
*
* The RAM difference is handled by the boot loader, so the only
* difference we end up handling here is the NAND flash.
*/
#ifdef CONFIG_BOARD_ATSTK1006
#include <linux/mtd/partitions.h>
#include <asm/arch/smc.h>
static struct smc_timing nand_timing __initdata = {
.ncs_read_setup = 0,
.nrd_setup = 10,
.ncs_write_setup = 0,
.nwe_setup = 10,
.ncs_read_pulse = 30,
.nrd_pulse = 15,
.ncs_write_pulse = 30,
.nwe_pulse = 15,
.read_cycle = 30,
.write_cycle = 30,
.ncs_read_recover = 0,
.nrd_recover = 15,
.ncs_write_recover = 0,
/* WE# high -> RE# low min 60 ns */
.nwe_recover = 50,
};
static struct smc_config nand_config __initdata = {
.bus_width = 1,
.nrd_controlled = 1,
.nwe_controlled = 1,
.nwait_mode = 0,
.byte_write = 0,
.tdf_cycles = 2,
.tdf_mode = 0,
};
static struct mtd_partition nand_partitions[] = {
{
.name = "main",
.offset = 0x00000000,
.size = MTDPART_SIZ_FULL,
},
};
static struct mtd_partition *nand_part_info(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(nand_partitions);
return nand_partitions;
}
struct atmel_nand_data atstk1006_nand_data __initdata = {
.cle = 21,
.ale = 22,
.rdy_pin = GPIO_PIN_PB(30),
.enable_pin = GPIO_PIN_PB(29),
.partition_info = nand_part_info,
};
#endif
struct eth_addr {
u8 addr[6];
};
@ -212,6 +280,12 @@ static int __init atstk1002_init(void)
at32_add_system_devices();
#ifdef CONFIG_BOARD_ATSTK1006
smc_set_timing(&nand_config, &nand_timing);
smc_set_configuration(3, &nand_config);
at32_add_device_nand(0, &atstk1006_nand_data);
#endif
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_add_device_usart(1);
#else