From db2b4bd09b43fc27ecd097e193f1135f5e40d347 Mon Sep 17 00:00:00 2001 From: Darren Etheridge Date: Fri, 21 Jun 2013 13:52:24 -0500 Subject: [PATCH] drm/tilcdc: fixing off by one errors found on analyzer When hooking up to an HDMI analyzer noticed some timings were off by one. Referring to the hardware technical reference manual for the lcd controller some of the timing registers use 0 to represent 1. This patch addresses that issue. Signed-off-by: Darren Etheridge Acked-by: Rob Clark Signed-off-by: Dave Airlie --- drivers/gpu/drm/tilcdc/tilcdc_crtc.c | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-) diff --git a/drivers/gpu/drm/tilcdc/tilcdc_crtc.c b/drivers/gpu/drm/tilcdc/tilcdc_crtc.c index b5b865f4f92b..086e52af1bc7 100644 --- a/drivers/gpu/drm/tilcdc/tilcdc_crtc.c +++ b/drivers/gpu/drm/tilcdc/tilcdc_crtc.c @@ -289,17 +289,22 @@ static int tilcdc_crtc_mode_set(struct drm_crtc *crtc, reg = tilcdc_read(dev, LCDC_RASTER_TIMING_2_REG) & ~0x000fff00; reg |= LCDC_AC_BIAS_FREQUENCY(info->ac_bias) | LCDC_AC_BIAS_TRANSITIONS_PER_INT(info->ac_bias_intrpt); + + /* + * subtract one from hfp, hbp, hsw because the hardware uses + * a value of 0 as 1 + */ if (priv->rev == 2) { - reg |= (hfp & 0x300) >> 8; - reg |= (hbp & 0x300) >> 4; - reg |= (hsw & 0x3c0) << 21; + reg |= ((hfp-1) & 0x300) >> 8; + reg |= ((hbp-1) & 0x300) >> 4; + reg |= ((hsw-1) & 0x3c0) << 21; } tilcdc_write(dev, LCDC_RASTER_TIMING_2_REG, reg); reg = (((mode->hdisplay >> 4) - 1) << 4) | - ((hbp & 0xff) << 24) | - ((hfp & 0xff) << 16) | - ((hsw & 0x3f) << 10); + (((hbp-1) & 0xff) << 24) | + (((hfp-1) & 0xff) << 16) | + (((hsw-1) & 0x3f) << 10); if (priv->rev == 2) reg |= (((mode->hdisplay >> 4) - 1) & 0x40) >> 3; tilcdc_write(dev, LCDC_RASTER_TIMING_0_REG, reg); @@ -307,7 +312,7 @@ static int tilcdc_crtc_mode_set(struct drm_crtc *crtc, reg = ((mode->vdisplay - 1) & 0x3ff) | ((vbp & 0xff) << 24) | ((vfp & 0xff) << 16) | - ((vsw & 0x3f) << 10); + (((vsw-1) & 0x3f) << 10); tilcdc_write(dev, LCDC_RASTER_TIMING_1_REG, reg); /*