mirror of
https://github.com/torvalds/linux.git
synced 2024-12-27 05:11:48 +00:00
USB: EHCI: Allow users to override 80% max periodic bandwidth
There are cases, when 80% max isochronous bandwidth is too limiting.
For example I have two USB video capture cards which stream uncompressed
video, and to stream full NTSC + PAL videos we'd need
NTSC 640x480 YUV422 @30fps ~17.6 MB/s
PAL 720x576 YUV422 @25fps ~19.7 MB/s
isoc bandwidth.
Now, due to limited alt settings in capture devices NTSC one ends up
streaming with max_pkt_size=2688 and PAL with max_pkt_size=2892, both
with interval=1. In terms of microframe time allocation this gives
NTSC ~53us
PAL ~57us
and together
~110us > 100us == 80% of 125us uframe time.
So those two devices can't work together simultaneously because the'd
over allocate isochronous bandwidth.
80% seemed a bit arbitrary to me, and I've tried to raise it to 90% and
both devices started to work together, so I though sometimes it would be
a good idea for users to override hardcoded default of max 80% isoc
bandwidth.
After all, isn't it a user who should decide how to load the bus? If I
can live with 10% or even 5% bulk bandwidth that should be ok. I'm a USB
newcomer, but that 80% set in stone by USB 2.0 specification seems to be
chosen pretty arbitrary to me, just to serve as a reasonable default.
NOTE 1
~~~~~~
for two streams with max_pkt_size=3072 (worst case) both time
allocation would be 60us+60us=120us which is 96% periodic bandwidth
leaving 4% for bulk and control. Alan Stern suggested that bulk then
would be problematic (less than 300*8 bittimes left per microframe), but
I think that is still enough for control traffic.
NOTE 2
~~~~~~
Sarah Sharp expressed concern that maxing out periodic bandwidth
could lead to vendor-specific hardware bugs on host controllers, because
> It's entirely possible that you'll run into
> vendor-specific bugs if you try to pack the schedule with isochronous
> transfers. I don't think any hardware designer would seriously test or
> validate their hardware with a schedule that is basically a violation of
> the USB bus spec (more than 80% for periodic transfers).
So far I've only tested this patch on my HP Mini 5103 with N10 chipset
kirr@mini:~$ lspci
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8059 PCI-E Gigabit Ethernet Controller (rev 11)
and the system works stable with 110us/uframe (~88%) isoc bandwith allocated for
above-mentioned isochronous transfers.
NOTE 3
~~~~~~
This feature is off by default. I mean max periodic bandwidth is set to
100us/uframe by default exactly as it was before the patch. So only those of us
who need the extreme settings are taking the risk - normal users who do not
alter uframe_periodic_max sysfs attribute should not see any change at all.
NOTE 4
~~~~~~
I've tried to update documentation in Documentation/ABI/ thoroughly, but
only "TBD" was put into Documentation/usb/ehci.txt -- the text there seems
to be outdated and much needing refreshing, before it could be amended.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit is contained in:
Kirill Smelkov
Greg Kroah-Hartman
parent
4c67045bfc
commit
cc62a7eb63
@ -10,3 +10,26 @@ KernelVersion: 2.6.35
|
||||
Contact: masa-korg@dsn.okisemi.com
|
||||
Description: Write/read Option ROM data.
|
||||
|
||||
|
||||
What: /sys/module/ehci_hcd/drivers/.../uframe_periodic_max
|
||||
Date: July 2011
|
||||
KernelVersion: 3.1
|
||||
Contact: Kirill Smelkov <kirr@mns.spb.ru>
|
||||
Description: Maximum time allowed for periodic transfers per microframe (μs)
|
||||
|
||||
[ USB 2.0 sets maximum allowed time for periodic transfers per
|
||||
microframe to be 80%, that is 100 microseconds out of 125
|
||||
microseconds (full microframe).
|
||||
|
||||
However there are cases, when 80% max isochronous bandwidth is
|
||||
too limiting. For example two video streams could require 110
|
||||
microseconds of isochronous bandwidth per microframe to work
|
||||
together. ]
|
||||
|
||||
Through this setting it is possible to raise the limit so that
|
||||
the host controller would allow allocating more than 100
|
||||
microseconds of periodic bandwidth per microframe.
|
||||
|
||||
Beware, non-standard modes are usually not thoroughly tested by
|
||||
hardware designers, and the hardware can malfunction when this
|
||||
setting differ from default 100.
|
||||
|
||||
@ -210,3 +210,5 @@ TBD: Interrupt and ISO transfer performance issues. Those periodic
|
||||
transfers are fully scheduled, so the main issue is likely to be how
|
||||
to trigger "high bandwidth" modes.
|
||||
|
||||
TBD: More than standard 80% periodic bandwidth allocation is possible
|
||||
through sysfs uframe_periodic_max parameter. Describe that.
|
||||
|
||||
@ -571,6 +571,12 @@ static int ehci_init(struct usb_hcd *hcd)
|
||||
|
||||
hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params);
|
||||
|
||||
/*
|
||||
* by default set standard 80% (== 100 usec/uframe) max periodic
|
||||
* bandwidth as required by USB 2.0
|
||||
*/
|
||||
ehci->uframe_periodic_max = 100;
|
||||
|
||||
/*
|
||||
* hw default: 1K periodic list heads, one per frame.
|
||||
* periodic_size can shrink by USBCMD update if hcc_params allows.
|
||||
|
||||
@ -172,7 +172,7 @@ periodic_usecs (struct ehci_hcd *ehci, unsigned frame, unsigned uframe)
|
||||
}
|
||||
}
|
||||
#ifdef DEBUG
|
||||
if (usecs > 100)
|
||||
if (usecs > ehci->uframe_periodic_max)
|
||||
ehci_err (ehci, "uframe %d sched overrun: %d usecs\n",
|
||||
frame * 8 + uframe, usecs);
|
||||
#endif
|
||||
@ -709,11 +709,8 @@ static int check_period (
|
||||
if (uframe >= 8)
|
||||
return 0;
|
||||
|
||||
/*
|
||||
* 80% periodic == 100 usec/uframe available
|
||||
* convert "usecs we need" to "max already claimed"
|
||||
*/
|
||||
usecs = 100 - usecs;
|
||||
/* convert "usecs we need" to "max already claimed" */
|
||||
usecs = ehci->uframe_periodic_max - usecs;
|
||||
|
||||
/* we "know" 2 and 4 uframe intervals were rejected; so
|
||||
* for period 0, check _every_ microframe in the schedule.
|
||||
@ -1286,9 +1283,9 @@ itd_slot_ok (
|
||||
{
|
||||
uframe %= period;
|
||||
do {
|
||||
/* can't commit more than 80% periodic == 100 usec */
|
||||
/* can't commit more than uframe_periodic_max usec */
|
||||
if (periodic_usecs (ehci, uframe >> 3, uframe & 0x7)
|
||||
> (100 - usecs))
|
||||
> (ehci->uframe_periodic_max - usecs))
|
||||
return 0;
|
||||
|
||||
/* we know urb->interval is 2^N uframes */
|
||||
@ -1345,7 +1342,7 @@ sitd_slot_ok (
|
||||
#endif
|
||||
|
||||
/* check starts (OUT uses more than one) */
|
||||
max_used = 100 - stream->usecs;
|
||||
max_used = ehci->uframe_periodic_max - stream->usecs;
|
||||
for (tmp = stream->raw_mask & 0xff; tmp; tmp >>= 1, uf++) {
|
||||
if (periodic_usecs (ehci, frame, uf) > max_used)
|
||||
return 0;
|
||||
@ -1354,7 +1351,7 @@ sitd_slot_ok (
|
||||
/* for IN, check CSPLIT */
|
||||
if (stream->c_usecs) {
|
||||
uf = uframe & 7;
|
||||
max_used = 100 - stream->c_usecs;
|
||||
max_used = ehci->uframe_periodic_max - stream->c_usecs;
|
||||
do {
|
||||
tmp = 1 << uf;
|
||||
tmp <<= 8;
|
||||
|
||||
@ -74,21 +74,117 @@ static ssize_t store_companion(struct device *dev,
|
||||
}
|
||||
static DEVICE_ATTR(companion, 0644, show_companion, store_companion);
|
||||
|
||||
|
||||
/*
|
||||
* Display / Set uframe_periodic_max
|
||||
*/
|
||||
static ssize_t show_uframe_periodic_max(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
char *buf)
|
||||
{
|
||||
struct ehci_hcd *ehci;
|
||||
int n;
|
||||
|
||||
ehci = hcd_to_ehci(bus_to_hcd(dev_get_drvdata(dev)));
|
||||
n = scnprintf(buf, PAGE_SIZE, "%d\n", ehci->uframe_periodic_max);
|
||||
return n;
|
||||
}
|
||||
|
||||
|
||||
static ssize_t store_uframe_periodic_max(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
const char *buf, size_t count)
|
||||
{
|
||||
struct ehci_hcd *ehci;
|
||||
unsigned uframe_periodic_max;
|
||||
unsigned frame, uframe;
|
||||
unsigned short allocated_max;
|
||||
unsigned long flags;
|
||||
ssize_t ret;
|
||||
|
||||
ehci = hcd_to_ehci(bus_to_hcd(dev_get_drvdata(dev)));
|
||||
if (kstrtouint(buf, 0, &uframe_periodic_max) < 0)
|
||||
return -EINVAL;
|
||||
|
||||
if (uframe_periodic_max < 100 || uframe_periodic_max >= 125) {
|
||||
ehci_info(ehci, "rejecting invalid request for "
|
||||
"uframe_periodic_max=%u\n", uframe_periodic_max);
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
ret = -EINVAL;
|
||||
|
||||
/*
|
||||
* lock, so that our checking does not race with possible periodic
|
||||
* bandwidth allocation through submitting new urbs.
|
||||
*/
|
||||
spin_lock_irqsave (&ehci->lock, flags);
|
||||
|
||||
/*
|
||||
* for request to decrease max periodic bandwidth, we have to check
|
||||
* every microframe in the schedule to see whether the decrease is
|
||||
* possible.
|
||||
*/
|
||||
if (uframe_periodic_max < ehci->uframe_periodic_max) {
|
||||
allocated_max = 0;
|
||||
|
||||
for (frame = 0; frame < ehci->periodic_size; ++frame)
|
||||
for (uframe = 0; uframe < 7; ++uframe)
|
||||
allocated_max = max(allocated_max,
|
||||
periodic_usecs (ehci, frame, uframe));
|
||||
|
||||
if (allocated_max > uframe_periodic_max) {
|
||||
ehci_info(ehci,
|
||||
"cannot decrease uframe_periodic_max becase "
|
||||
"periodic bandwidth is already allocated "
|
||||
"(%u > %u)\n",
|
||||
allocated_max, uframe_periodic_max);
|
||||
goto out_unlock;
|
||||
}
|
||||
}
|
||||
|
||||
/* increasing is always ok */
|
||||
|
||||
ehci_info(ehci, "setting max periodic bandwidth to %u%% "
|
||||
"(== %u usec/uframe)\n",
|
||||
100*uframe_periodic_max/125, uframe_periodic_max);
|
||||
|
||||
if (uframe_periodic_max != 100)
|
||||
ehci_warn(ehci, "max periodic bandwidth set is non-standard\n");
|
||||
|
||||
ehci->uframe_periodic_max = uframe_periodic_max;
|
||||
ret = count;
|
||||
|
||||
out_unlock:
|
||||
spin_unlock_irqrestore (&ehci->lock, flags);
|
||||
return ret;
|
||||
}
|
||||
static DEVICE_ATTR(uframe_periodic_max, 0644, show_uframe_periodic_max, store_uframe_periodic_max);
|
||||
|
||||
|
||||
static inline int create_sysfs_files(struct ehci_hcd *ehci)
|
||||
{
|
||||
struct device *controller = ehci_to_hcd(ehci)->self.controller;
|
||||
int i = 0;
|
||||
|
||||
/* with integrated TT there is no companion! */
|
||||
if (!ehci_is_TDI(ehci))
|
||||
i = device_create_file(ehci_to_hcd(ehci)->self.controller,
|
||||
&dev_attr_companion);
|
||||
i = device_create_file(controller, &dev_attr_companion);
|
||||
if (i)
|
||||
goto out;
|
||||
|
||||
i = device_create_file(controller, &dev_attr_uframe_periodic_max);
|
||||
out:
|
||||
return i;
|
||||
}
|
||||
|
||||
static inline void remove_sysfs_files(struct ehci_hcd *ehci)
|
||||
{
|
||||
struct device *controller = ehci_to_hcd(ehci)->self.controller;
|
||||
|
||||
/* with integrated TT there is no companion! */
|
||||
if (!ehci_is_TDI(ehci))
|
||||
device_remove_file(ehci_to_hcd(ehci)->self.controller,
|
||||
&dev_attr_companion);
|
||||
device_remove_file(controller, &dev_attr_companion);
|
||||
|
||||
device_remove_file(controller, &dev_attr_uframe_periodic_max);
|
||||
}
|
||||
|
||||
@ -87,6 +87,8 @@ struct ehci_hcd { /* one per controller */
|
||||
union ehci_shadow *pshadow; /* mirror hw periodic table */
|
||||
int next_uframe; /* scan periodic, start here */
|
||||
unsigned periodic_sched; /* periodic activity count */
|
||||
unsigned uframe_periodic_max; /* max periodic time per uframe */
|
||||
|
||||
|
||||
/* list of itds & sitds completed while clock_frame was still active */
|
||||
struct list_head cached_itd_list;
|
||||
|
||||
Loading…
Reference in New Issue
Block a user