usb: fixes for v4.15-rc4

We have a few fixes on dwc3:
 
 - one fix which only happens with some implementations where we need to
   wait longer for some commands to finish.
 
 - Another fix for high-bandwidth isochronous endpoint programming making
   sure that we send the correct DATA tokens in the correct sequence
 
 - A couple PM fixes on dwc3-of-simple
 
 The other synopsys controller driver (dwc2) got a fix for FIFO size
 programming.
 
 Other than these, we have a couple Kconfig fixes making sure that
 dependencies are properly setup.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlovtj8dHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYkhg/+Js7q/csuLfknxIeU
 0FT0exGWBr/XNWDwvckS65yR6zFgG6txRmuuHTq1BcqiOL6jpqV0D8VoAUt/rv1U
 HrUPYMaS8Y5qpYZOe28NyyFgl+5CuoYdLkToAqUrX1MRXClt4Cx+XeJ6yOM6heXb
 codXGef04oCTVYbDuPBbO1S99Pi1nw2T7jOLrhwegAGKEBMCzv+uT/qCR/uG5Fzr
 5GHWWQyHLlo3Av29Rmp4GCFONlyxzGyKTKN+tFAVurGsO9UN8zY2BhfP6mH3kG64
 dyef/hWJ4adhxnbTlrjrnZ52RBePhuUzqXDpKPrCYr9mlsI9NfPk6ablvHkF4W5K
 bXqE8YTuiRdQIRS1+3LbK0BSsuC4svVD3QpN2fghPhkcxPg2FnR4eI3t5IupM6Hz
 tqZvn4BU1UPdrRO3FBmyY/ZMTzsk5u4GB81FUUJRqQlg9cPTcjAWTmwox8fVzf6j
 B2uC59qRn5KDMTKOyCU2CATo3Oi211WCWsUtnO7+mXxknyaWOjWI0MfV0fB3OLIj
 IPm/PVfNcECjiOOpgyhSUY5YbIkQpD3/u9U8cuC+2Q2na7Cftsy/tJLrVlKgLXvQ
 VgHoHGwSPkGdrClRp5mB0c5m2byPAE+BaOleSmeepiq2dDUvgr8hjgBURooKpC9j
 mfNmZrsJgYXQIU9v6E0z92PH/+0=
 =6T1G
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.15-rc4

We have a few fixes on dwc3:

- one fix which only happens with some implementations where we need to
  wait longer for some commands to finish.

- Another fix for high-bandwidth isochronous endpoint programming making
  sure that we send the correct DATA tokens in the correct sequence

- A couple PM fixes on dwc3-of-simple

The other synopsys controller driver (dwc2) got a fix for FIFO size
programming.

Other than these, we have a couple Kconfig fixes making sure that
dependencies are properly setup.
This commit is contained in:
Greg Kroah-Hartman 2017-12-12 12:51:05 +01:00
commit c1ed473554
844 changed files with 7677 additions and 5057 deletions

View File

@ -15,7 +15,7 @@ Required properties:
Example:
ccn@0x2000000000 {
ccn@2000000000 {
compatible = "arm,ccn-504";
reg = <0x20 0x00000000 0 0x1000000>;
interrupts = <0 181 4>;

View File

@ -49,7 +49,7 @@ An interrupt consumer on an SoC using crossbar will use:
interrupts = <GIC_SPI request_number interrupt_level>
Example:
device_x@0x4a023000 {
device_x@4a023000 {
/* Crossbar 8 used */
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
...

View File

@ -8,7 +8,7 @@ Required properties:
- interrupts : Should contain MC General interrupt.
Example:
memory-controller@0x7000f000 {
memory-controller@7000f000 {
compatible = "nvidia,tegra20-mc";
reg = <0x7000f000 0x024
0x7000f03c 0x3c4>;

View File

@ -17,7 +17,7 @@ Optional properties:
- clock-output-names : From common clock binding.
Example:
clock@0xff000000 {
clock@ff000000 {
compatible = "adi,axi-clkgen";
#clock-cells = <0>;
reg = <0xff000000 0x1000>;

View File

@ -23,7 +23,7 @@ Example:
clocks = <&clk_osc>;
};
aux: aux@0x7e215004 {
aux: aux@7e215004 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;
reg = <0x7e215000 0x8>;

View File

@ -24,7 +24,7 @@ tree sources.
Example 1: An example of a clock controller node is listed below.
clock: clock-controller@0x10030000 {
clock: clock-controller@10030000 {
compatible = "samsung,exynos4210-clock";
reg = <0x10030000 0x20000>;
#clock-cells = <1>;

View File

@ -22,7 +22,7 @@ tree sources.
Example 1: An example of a clock controller node is listed below.
clock: clock-controller@0x10010000 {
clock: clock-controller@10010000 {
compatible = "samsung,exynos5250-clock";
reg = <0x10010000 0x30000>;
#clock-cells = <1>;

View File

@ -30,7 +30,7 @@ Example 1: An example of a clock controller node is listed below.
#clock-cells = <0>;
};
clock: clock-controller@0x10010000 {
clock: clock-controller@10010000 {
compatible = "samsung,exynos5410-clock";
reg = <0x10010000 0x30000>;
#clock-cells = <1>;

View File

@ -23,7 +23,7 @@ tree sources.
Example 1: An example of a clock controller node is listed below.
clock: clock-controller@0x10010000 {
clock: clock-controller@10010000 {
compatible = "samsung,exynos5420-clock";
reg = <0x10010000 0x30000>;
#clock-cells = <1>;

View File

@ -21,7 +21,7 @@ tree sources.
Example: An example of a clock controller node is listed below.
clock: clock-controller@0x10010000 {
clock: clock-controller@10010000 {
compatible = "samsung,exynos5440-clock";
reg = <0x160000 0x10000>;
#clock-cells = <1>;

View File

@ -14,7 +14,7 @@ Required properties:
Example:
pllctrl: pll-controller@0x02310000 {
pllctrl: pll-controller@02310000 {
compatible = "ti,keystone-pllctrl", "syscon";
reg = <0x02310000 0x200>;
};

View File

@ -20,13 +20,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296702-clock.h
for the full list of zx296702 clock IDs.
topclk: topcrm@0x09800000 {
topclk: topcrm@09800000 {
compatible = "zte,zx296702-topcrm-clk";
reg = <0x09800000 0x1000>;
#clock-cells = <1>;
};
uart0: serial@0x09405000 {
uart0: serial@09405000 {
compatible = "zte,zx296702-uart";
reg = <0x09405000 0x1000>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;

View File

@ -456,7 +456,7 @@ System ON/OFF key driver
Definition: this is phandle to the register map node.
EXAMPLE:
snvs-pwrkey@0x020cc000 {
snvs-pwrkey@020cc000 {
compatible = "fsl,sec-v4.0-pwrkey";
regmap = <&snvs>;
interrupts = <0 4 0x4>
@ -545,7 +545,7 @@ FULL EXAMPLE
interrupts = <93 2>;
};
snvs-pwrkey@0x020cc000 {
snvs-pwrkey@020cc000 {
compatible = "fsl,sec-v4.0-pwrkey";
regmap = <&sec_mon>;
interrupts = <0 4 0x4>;

View File

@ -9,7 +9,7 @@ Required properties:
- clock-names : the name of clock used by the DFI, must be "pclk_ddr_mon";
Example:
dfi: dfi@0xff630000 {
dfi: dfi@ff630000 {
compatible = "rockchip,rk3399-dfi";
reg = <0x00 0xff630000 0x00 0x4000>;
rockchip,pmu = <&pmugrf>;

View File

@ -27,7 +27,7 @@ Optional properties:
Example:
fb0: fb@0x00500000 {
fb0: fb@00500000 {
compatible = "atmel,at91sam9g45-lcdc";
reg = <0x00500000 0x1000>;
interrupts = <23 3 0>;
@ -41,7 +41,7 @@ Example:
Example for fixed framebuffer memory:
fb0: fb@0x00500000 {
fb0: fb@00500000 {
compatible = "atmel,at91sam9263-lcdc";
reg = <0x00700000 0x1000 0x70000000 0x200000>;
[...]

View File

@ -73,7 +73,7 @@ Hypervisor OS configuration:
max-read-transactions = <31>;
channel-reset-timeout-cycles = <0x500>;
hidma_24: dma-controller@0x5c050000 {
hidma_24: dma-controller@5c050000 {
compatible = "qcom,hidma-1.0";
reg = <0 0x5c050000 0x0 0x1000>,
<0 0x5c0b0000 0x0 0x1000>;
@ -85,7 +85,7 @@ Hypervisor OS configuration:
Guest OS configuration:
hidma_24: dma-controller@0x5c050000 {
hidma_24: dma-controller@5c050000 {
compatible = "qcom,hidma-1.0";
reg = <0 0x5c050000 0x0 0x1000>,
<0 0x5c0b0000 0x0 0x1000>;

View File

@ -13,7 +13,7 @@ Required properties:
Example:
Controller:
dma: dma-controller@0x09c00000{
dma: dma-controller@09c00000{
compatible = "zte,zx296702-dma";
reg = <0x09c00000 0x1000>;
clocks = <&topclk ZX296702_DMA_ACLK>;

View File

@ -1,7 +1,12 @@
EEPROMs (SPI) compatible with Atmel at25.
Required properties:
- compatible : "atmel,at25".
- compatible : Should be "<vendor>,<type>", and generic value "atmel,at25".
Example "<vendor>,<type>" values:
"microchip,25lc040"
"st,m95m02"
"st,m95256"
- reg : chip select number
- spi-max-frequency : max spi frequency to use
- pagesize : size of the eeprom page
@ -13,7 +18,7 @@ Optional properties:
- spi-cpol : SPI inverse clock polarity, as per spi-bus bindings.
- read-only : this parameter-less property disables writes to the eeprom
Obsolete legacy properties are can be used in place of "size", "pagesize",
Obsolete legacy properties can be used in place of "size", "pagesize",
"address-width", and "read-only":
- at25,byte-len : total eeprom size in bytes
- at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
@ -22,8 +27,8 @@ Obsolete legacy properties are can be used in place of "size", "pagesize",
Additional compatible properties are also allowed.
Example:
at25@0 {
compatible = "atmel,at25", "st,m95256";
eeprom@0 {
compatible = "st,m95256", "atmel,at25";
reg = <0>
spi-max-frequency = <5000000>;
spi-cpha;

View File

@ -30,7 +30,7 @@ Optional properties:
Example:
gpio_altr: gpio@0xff200000 {
gpio_altr: gpio@ff200000 {
compatible = "altr,pio-1.0";
reg = <0xff200000 0x10>;
interrupts = <0 45 4>;

View File

@ -18,7 +18,7 @@ Optional properties:
Example
/ {
i2c4: i2c4@0x10054000 {
i2c4: i2c4@10054000 {
compatible = "ingenic,jz4780-i2c";
reg = <0x10054000 0x1000>;

View File

@ -10,7 +10,7 @@ Required properties:
Example:
hp03@0x77 {
hp03@77 {
compatible = "hoperf,hp03";
reg = <0x77>;
xclr-gpio = <&portc 0 0x0>;

View File

@ -15,7 +15,7 @@ Optional properties:
Example:
i2c@80110000 {
bu21013_tp@0x5c {
bu21013_tp@5c {
compatible = "rohm,bu21013_tp";
reg = <0x5c>;
touch-gpio = <&gpio2 20 0x4>;

View File

@ -155,7 +155,7 @@ Example:
<0x0 0xe112f000 0 0x02000>,
<0x0 0xe1140000 0 0x10000>,
<0x0 0xe1160000 0 0x10000>;
v2m0: v2m@0x8000 {
v2m0: v2m@8000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x80000 0 0x1000>;
@ -163,7 +163,7 @@ Example:
....
v2mN: v2m@0x9000 {
v2mN: v2m@9000 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x90000 0 0x1000>;

View File

@ -71,7 +71,7 @@ Example 2:
* An interrupt generating device that is wired to a Meta external
* trigger block.
*/
uart1: uart@0x02004c00 {
uart1: uart@02004c00 {
// Interrupt source '5' that is level-sensitive.
// Note that there are only two cells as specified in the
// interrupt parent's '#interrupt-cells' property.

View File

@ -51,7 +51,7 @@ Example 1:
/*
* TZ1090 PDC block
*/
pdc: pdc@0x02006000 {
pdc: pdc@02006000 {
// This is an interrupt controller node.
interrupt-controller;

View File

@ -39,7 +39,7 @@ Example:
The following is an example from the SPEAr320 SoC dtsi file.
shirq: interrupt-controller@0xb3000000 {
shirq: interrupt-controller@b3000000 {
compatible = "st,spear320-shirq";
reg = <0xb3000000 0x1000>;
interrupts = <28 29 30 1>;

View File

@ -14,7 +14,7 @@ Optional properties:
depends on the interrupt controller parent.
Example:
mbox_tx: mailbox@0x100 {
mbox_tx: mailbox@100 {
compatible = "altr,mailbox-1.0";
reg = <0x100 0x8>;
interrupt-parent = < &gic_0 >;
@ -22,7 +22,7 @@ Example:
#mbox-cells = <1>;
};
mbox_rx: mailbox@0x200 {
mbox_rx: mailbox@200 {
compatible = "altr,mailbox-1.0";
reg = <0x200 0x8>;
interrupt-parent = < &gic_0 >;
@ -40,7 +40,7 @@ support only one channel).The equivalent "mbox-names" property value can be
used to give a name to the communication channel to be used by the client user.
Example:
mclient0: mclient0@0x400 {
mclient0: mclient0@400 {
compatible = "client-1.0";
reg = <0x400 0x10>;
mbox-names = "mbox-tx", "mbox-rx";

View File

@ -15,7 +15,7 @@ Optional properties:
- brcm,use-bcm-hdr: present if a BCM header precedes each frame.
Example:
pdc0: iproc-pdc0@0x612c0000 {
pdc0: iproc-pdc0@612c0000 {
compatible = "brcm,iproc-pdc-mbox";
reg = <0 0x612c0000 0 0x445>; /* PDC FS0 regs */
interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;

View File

@ -17,7 +17,7 @@ Optional properties:
Example:
gsc_0: gsc@0x13e00000 {
gsc_0: gsc@13e00000 {
compatible = "samsung,exynos5250-gsc";
reg = <0x13e00000 0x1000>;
interrupts = <0 85 0>;

View File

@ -68,7 +68,7 @@ vcodec_dec: vcodec@16000000 {
"vdec_bus_clk_src";
};
vcodec_enc: vcodec@0x18002000 {
vcodec_enc: vcodec@18002000 {
compatible = "mediatek,mt8173-vcodec-enc";
reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/
<0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/

View File

@ -44,7 +44,7 @@ Device node example
vin0 = &vin0;
};
vin0: vin@0xe6ef0000 {
vin0: vin@e6ef0000 {
compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin";
clocks = <&mstp8_clks R8A7790_CLK_VIN0>;
reg = <0 0xe6ef0000 0 0x1000>;

View File

@ -138,7 +138,7 @@ Example:
};
/* MIPI CSI-2 bus IF sensor */
s5c73m3: sensor@0x1a {
s5c73m3: sensor@1a {
compatible = "samsung,s5c73m3";
reg = <0x1a>;
vddio-supply = <...>;

View File

@ -8,7 +8,7 @@ Bindings, specific for the sh_mobile_ceu_camera.c driver:
Example:
ceu0: ceu@0xfe910000 {
ceu0: ceu@fe910000 {
compatible = "renesas,sh-mobile-ceu";
reg = <0xfe910000 0xa0>;
interrupt-parent = <&intcs>;

View File

@ -154,7 +154,7 @@ imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a
'port' node which may indicate that at any time only one of the following data
pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
ceu0: ceu@0xfe910000 {
ceu0: ceu@fe910000 {
compatible = "renesas,sh-mobile-ceu";
reg = <0xfe910000 0xa0>;
interrupts = <0x880>;
@ -193,9 +193,9 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
};
};
i2c0: i2c@0xfff20000 {
i2c0: i2c@fff20000 {
...
ov772x_1: camera@0x21 {
ov772x_1: camera@21 {
compatible = "ovti,ov772x";
reg = <0x21>;
vddio-supply = <&regulator1>;
@ -219,7 +219,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
};
};
imx074: camera@0x1a {
imx074: camera@1a {
compatible = "sony,imx074";
reg = <0x1a>;
vddio-supply = <&regulator1>;
@ -239,7 +239,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
};
};
csi2: csi2@0xffc90000 {
csi2: csi2@ffc90000 {
compatible = "renesas,sh-mobile-csi2";
reg = <0xffc90000 0x1000>;
interrupts = <0x17a0>;

View File

@ -46,7 +46,7 @@ Optional properties:
Example:
emif1: emif@0x4c000000 {
emif1: emif@4c000000 {
compatible = "ti,emif-4d";
ti,hwmods = "emif2";
phy-type = <1>;

View File

@ -13,7 +13,7 @@ Required properties:
Example:
devctrl: device-state-control@0x02620000 {
devctrl: device-state-control@02620000 {
compatible = "ti,keystone-devctrl", "syscon";
reg = <0x02620000 0x1000>;
};

View File

@ -9,7 +9,7 @@ Required properties:
- reg : Location and size of bounce buffer
Example:
smc@0x3404c000 {
smc@3404c000 {
compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
reg = <0x3404c000 0x400>; //1 KiB in SRAM
};

View File

@ -12,7 +12,7 @@ Refer to clocks/clock-bindings.txt for generic clock consumer properties.
Example:
sdio2: sdio@0x3f1a0000 {
sdio2: sdio@3f1a0000 {
compatible = "brcm,kona-sdhci";
reg = <0x3f1a0000 0x10000>;
clocks = <&sdio3_clk>;

View File

@ -24,7 +24,7 @@ Optional properties:
Example:
sdhci0: sdhci@0x18041000 {
sdhci0: sdhci@18041000 {
compatible = "brcm,sdhci-iproc-cygnus";
reg = <0x18041000 0x100>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;

View File

@ -55,7 +55,7 @@ Examples:
[hwmod populated DMA resources]
mmc1: mmc@0x4809c000 {
mmc1: mmc@4809c000 {
compatible = "ti,omap4-hsmmc";
reg = <0x4809c000 0x400>;
ti,hwmods = "mmc1";
@ -67,7 +67,7 @@ Examples:
[generic DMA request binding]
mmc1: mmc@0x4809c000 {
mmc1: mmc@4809c000 {
compatible = "ti,omap4-hsmmc";
reg = <0x4809c000 0x400>;
ti,hwmods = "mmc1";

View File

@ -82,15 +82,15 @@ gpmc: gpmc@6e000000 {
label = "bootloader-nor";
reg = <0 0x40000>;
};
partition@0x40000 {
partition@40000 {
label = "params-nor";
reg = <0x40000 0x40000>;
};
partition@0x80000 {
partition@80000 {
label = "kernel-nor";
reg = <0x80000 0x200000>;
};
partition@0x280000 {
partition@280000 {
label = "filesystem-nor";
reg = <0x240000 0x7d80000>;
};

View File

@ -131,7 +131,7 @@ Example:
read-only;
reg = <0x00000000 0x00400000>;
};
android@0x00400000 {
android@00400000 {
label = "android";
reg = <0x00400000 0x12c00000>;
};

View File

@ -52,7 +52,7 @@ Optional properties:
Example:
tse_sub_0_eth_tse_0: ethernet@0x1,00000000 {
tse_sub_0_eth_tse_0: ethernet@1,00000000 {
compatible = "altr,tse-msgdma-1.0";
reg = <0x00000001 0x00000000 0x00000400>,
<0x00000001 0x00000460 0x00000020>,
@ -90,7 +90,7 @@ Example:
};
};
tse_sub_1_eth_tse_0: ethernet@0x1,00001000 {
tse_sub_1_eth_tse_0: ethernet@1,00001000 {
compatible = "altr,tse-msgdma-1.0";
reg = <0x00000001 0x00001000 0x00000400>,
<0x00000001 0x00001460 0x00000020>,

View File

@ -18,7 +18,7 @@ Example :
This example shows these optional properties, plus other properties
required for the TI Davinci MDIO driver.
davinci_mdio: ethernet@0x5c030000 {
davinci_mdio: ethernet@5c030000 {
compatible = "ti,davinci_mdio";
reg = <0x5c030000 0x1000>;
#address-cells = <1>;

View File

@ -28,7 +28,7 @@ Required properties:
Example:
gmii_to_sgmii_converter: phy@0x100000240 {
gmii_to_sgmii_converter: phy@100000240 {
compatible = "altr,gmii-to-sgmii-2.0";
reg = <0x00000001 0x00000240 0x00000008>,
<0x00000001 0x00000200 0x00000040>;

View File

@ -36,7 +36,7 @@ Optional properties:
Example:
cpu@0x0 {
cpu@0 {
device_type = "cpu";
compatible = "altr,nios2-1.0";
reg = <0>;

View File

@ -25,7 +25,7 @@ Optional properties:
- bus-range: PCI bus numbers covered
Example
pcie_0: pcie@0xc00000000 {
pcie_0: pcie@c00000000 {
compatible = "altr,pcie-root-port-1.0";
reg = <0xc0000000 0x20000000>,
<0xff220000 0x00004000>;

View File

@ -52,7 +52,7 @@ Additional required properties for imx7d-pcie:
Example:
pcie@0x01000000 {
pcie@01000000 {
compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
reg = <0x01ffc000 0x04000>,
<0x01f00000 0x80000>;

View File

@ -21,7 +21,7 @@ Optional properties:
- dma-coherent: Present if DMA operations are coherent.
Hip05 Example (note that Hip06 is the same except compatible):
pcie@0xb0080000 {
pcie@b0080000 {
compatible = "hisilicon,hip05-pcie", "snps,dw-pcie";
reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>;
reg-names = "rc_dbi", "config";

View File

@ -45,7 +45,7 @@ Optional properties:
- usb3_vbus-supply : regulator phandle for controller usb3 vbus
Example:
usbphy: phy@0x01c13400 {
usbphy: phy@01c13400 {
#phy-cells = <1>;
compatible = "allwinner,sun4i-a10-usb-phy";
/* phy base regs, phy1 pmu reg, phy2 pmu reg */

View File

@ -25,7 +25,7 @@ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
For example:
pinmux: pinmux@0x0301d0c8 {
pinmux: pinmux@0301d0c8 {
compatible = "brcm,cygnus-pinmux";
reg = <0x0301d0c8 0x1b0>;

View File

@ -96,14 +96,14 @@ For example, pinctrl might have subnodes like the following:
For a specific board, if it wants to use sd1,
it can add the following to its board-specific .dts file.
sd1: sd@0x12340000 {
sd1: sd@12340000 {
pinctrl-names = "default";
pinctrl-0 = <&sd1_pmx0>;
}
or
sd1: sd@0x12340000 {
sd1: sd@12340000 {
pinctrl-names = "default";
pinctrl-0 = <&sd1_pmx1>;
}

View File

@ -41,7 +41,7 @@ For example, pinctrl might have subnodes like the following:
For a specific board, if it wants to use uart2 without hardware flow control,
it can add the following to its board-specific .dts file.
uart2: uart@0xb0070000 {
uart2: uart@b0070000 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_noflow_pins_a>;
}

View File

@ -136,7 +136,7 @@ Example for rk3188:
#size-cells = <1>;
ranges;
gpio0: gpio0@0x2000a000 {
gpio0: gpio0@2000a000 {
compatible = "rockchip,rk3188-gpio-bank0";
reg = <0x2000a000 0x100>;
interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@ -149,7 +149,7 @@ Example for rk3188:
#interrupt-cells = <2>;
};
gpio1: gpio1@0x2003c000 {
gpio1: gpio1@2003c000 {
compatible = "rockchip,gpio-bank";
reg = <0x2003c000 0x100>;
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;

View File

@ -107,7 +107,7 @@ regulators (twl_reg1 and twl_reg2),
...
};
mmc: mmc@0x0 {
mmc: mmc@0 {
...
...
vmmc-supply = <&twl_reg1>;

View File

@ -12,7 +12,7 @@ Optional properties:
Example:
uart@0x4000c400 {
uart@4000c400 {
compatible = "energymicro,efm32-uart";
reg = <0x4000c400 0x400>;
interrupts = <15>;

View File

@ -14,7 +14,7 @@ Required properties:
Example:
ps20: ps2@0x01c2a000 {
ps20: ps2@01c2a000 {
compatible = "allwinner,sun4i-a10-ps2";
reg = <0x01c2a000 0x400>;
interrupts = <0 62 4>;

View File

@ -220,7 +220,7 @@ qmss: qmss@2a40000 {
#address-cells = <1>;
#size-cells = <1>;
ranges;
pdsp0@0x2a10000 {
pdsp0@2a10000 {
reg = <0x2a10000 0x1000>,
<0x2a0f000 0x100>,
<0x2a0c000 0x3c8>,

View File

@ -21,7 +21,7 @@ please check:
Example:
i2s: i2s@0x77600000 {
i2s: i2s@77600000 {
compatible = "adi,axi-i2s-1.00.a";
reg = <0x77600000 0x1000>;
clocks = <&clk 15>, <&audio_clock>;

View File

@ -20,7 +20,7 @@ please check:
Example:
spdif: spdif@0x77400000 {
spdif: spdif@77400000 {
compatible = "adi,axi-spdif-tx-1.00.a";
reg = <0x77600000 0x1000>;
clocks = <&clk 15>, <&audio_clock>;

View File

@ -20,7 +20,7 @@ Optional properties:
Example:
&i2c {
ak4613: ak4613@0x10 {
ak4613: ak4613@10 {
compatible = "asahi-kasei,ak4613";
reg = <0x10>;
};

View File

@ -17,7 +17,7 @@ Optional properties:
Example 1:
&i2c {
ak4648: ak4648@0x12 {
ak4648: ak4648@12 {
compatible = "asahi-kasei,ak4642";
reg = <0x12>;
};

View File

@ -10,7 +10,7 @@ Required properties:
Example:
&i2c {
max98371: max98371@0x31 {
max98371: max98371@31 {
compatible = "maxim,max98371";
reg = <0x31>;
};

View File

@ -10,7 +10,7 @@ Required properties:
Example:
&i2c {
max9867: max9867@0x18 {
max9867: max9867@18 {
compatible = "maxim,max9867";
reg = <0x18>;
};

View File

@ -20,7 +20,7 @@ Required properties:
Example:
sh_fsi2: sh_fsi2@0xec230000 {
sh_fsi2: sh_fsi2@ec230000 {
compatible = "renesas,sh_fsi2";
reg = <0xec230000 0x400>;
interrupts = <0 146 0x4>;

View File

@ -33,7 +33,7 @@ Required properties on RK3288:
Example for the rk3188 SPDIF controller:
spdif: spdif@0x1011e000 {
spdif: spdif@1011e000 {
compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif";
reg = <0x1011e000 0x2000>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;

View File

@ -51,7 +51,7 @@ Optional properties:
Example:
sti_uni_player1: sti-uni-player@0x8D81000 {
sti_uni_player1: sti-uni-player@8D81000 {
compatible = "st,stih407-uni-player-hdmi";
#sound-dai-cells = <0>;
st,syscfg = <&syscfg_core>;
@ -63,7 +63,7 @@ Example:
st,tdm-mode = <1>;
};
sti_uni_player2: sti-uni-player@0x8D82000 {
sti_uni_player2: sti-uni-player@8D82000 {
compatible = "st,stih407-uni-player-pcm-out";
#sound-dai-cells = <0>;
st,syscfg = <&syscfg_core>;
@ -74,7 +74,7 @@ Example:
dma-names = "tx";
};
sti_uni_player3: sti-uni-player@0x8D85000 {
sti_uni_player3: sti-uni-player@8D85000 {
compatible = "st,stih407-uni-player-spdif";
#sound-dai-cells = <0>;
st,syscfg = <&syscfg_core>;
@ -85,7 +85,7 @@ Example:
dma-names = "tx";
};
sti_uni_reader1: sti-uni-reader@0x8D84000 {
sti_uni_reader1: sti-uni-reader@8D84000 {
compatible = "st,stih407-uni-reader-hdmi";
#sound-dai-cells = <0>;
st,syscfg = <&syscfg_core>;

View File

@ -19,7 +19,7 @@ Recommended properties :
Example:
spi1: spi@0x4000c400 { /* USART1 */
spi1: spi@4000c400 { /* USART1 */
#address-cells = <1>;
#size-cells = <0>;
compatible = "energymicro,efm32-spi";

View File

@ -239,7 +239,7 @@ cpus {
* A simple fan controller which supports 10 speeds of operation
* (represented as 0-9).
*/
fan0: fan@0x48 {
fan0: fan@48 {
...
cooling-min-level = <0>;
cooling-max-level = <9>;
@ -252,7 +252,7 @@ ocp {
/*
* A simple IC with a single bandgap temperature sensor.
*/
bandgap0: bandgap@0x0000ED00 {
bandgap0: bandgap@0000ED00 {
...
#thermal-sensor-cells = <0>;
};
@ -330,7 +330,7 @@ ocp {
/*
* A simple IC with several bandgap temperature sensors.
*/
bandgap0: bandgap@0x0000ED00 {
bandgap0: bandgap@0000ED00 {
...
#thermal-sensor-cells = <1>;
};
@ -447,7 +447,7 @@ one thermal zone.
/*
* A simple IC with a single temperature sensor.
*/
adc: sensor@0x49 {
adc: sensor@49 {
...
#thermal-sensor-cells = <0>;
};
@ -458,7 +458,7 @@ ocp {
/*
* A simple IC with a single bandgap temperature sensor.
*/
bandgap0: bandgap@0x0000ED00 {
bandgap0: bandgap@0000ED00 {
...
#thermal-sensor-cells = <0>;
};
@ -516,7 +516,7 @@ with many sensors and many cooling devices.
/*
* An IC with several temperature sensor.
*/
adc_dummy: sensor@0x50 {
adc_dummy: sensor@50 {
...
#thermal-sensor-cells = <1>; /* sensor internal ID */
};

View File

@ -32,7 +32,7 @@ Optional properties:
Example:
ufsphy1: ufsphy@0xfc597000 {
ufsphy1: ufsphy@fc597000 {
compatible = "qcom,ufs-phy-qmp-20nm";
reg = <0xfc597000 0x800>;
reg-names = "phy_mem";
@ -53,7 +53,7 @@ Example:
<&clock_gcc clk_gcc_ufs_rx_cfg_clk>;
};
ufshc@0xfc598000 {
ufshc@fc598000 {
...
phys = <&ufsphy1>;
phy-names = "ufsphy";

View File

@ -46,7 +46,7 @@ Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
Example:
ufshc@0xfc598000 {
ufshc@fc598000 {
compatible = "jedec,ufs-1.1";
reg = <0xfc598000 0x800>;
interrupts = <0 28 0>;

View File

@ -95,6 +95,7 @@ usb: usb@47400000 {
reg = <0x47401300 0x100>;
reg-names = "phy";
ti,ctrl_mod = <&ctrl_mod>;
#phy-cells = <0>;
};
usb0: usb@47401000 {
@ -141,6 +142,7 @@ usb: usb@47400000 {
reg = <0x47401b00 0x100>;
reg-names = "phy";
ti,ctrl_mod = <&ctrl_mod>;
#phy-cells = <0>;
};
usb1: usb@47401800 {

View File

@ -22,7 +22,7 @@ See: Documentation/devicetree/bindings/reset/reset.txt
Example:
ehci1: usb@0xfe203e00 {
ehci1: usb@fe203e00 {
compatible = "st,st-ehci-300x";
reg = <0xfe203e00 0x100>;
interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>;

View File

@ -20,7 +20,7 @@ See: Documentation/devicetree/bindings/reset/reset.txt
Example:
ohci0: usb@0xfe1ffc00 {
ohci0: usb@fe1ffc00 {
compatible = "st,st-ohci-300x";
reg = <0xfe1ffc00 0x100>;
interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>;

View File

@ -6,7 +6,7 @@ reg: Register address and length for watchdog registers
Example:
watchdog: jz4740-watchdog@0x10002000 {
watchdog: jz4740-watchdog@10002000 {
compatible = "ingenic,jz4740-watchdog";
reg = <0x10002000 0x100>;
};

View File

@ -0,0 +1,30 @@
****************
Frontend drivers
****************
Frontend attach headers
***********************
.. Keep it on alphabetic order
.. kernel-doc:: drivers/media/dvb-frontends/a8293.h
.. kernel-doc:: drivers/media/dvb-frontends/af9013.h
.. kernel-doc:: drivers/media/dvb-frontends/ascot2e.h
.. kernel-doc:: drivers/media/dvb-frontends/cxd2820r.h
.. kernel-doc:: drivers/media/dvb-frontends/drxk.h
.. kernel-doc:: drivers/media/dvb-frontends/dvb-pll.h
.. kernel-doc:: drivers/media/dvb-frontends/helene.h
.. kernel-doc:: drivers/media/dvb-frontends/horus3a.h
.. kernel-doc:: drivers/media/dvb-frontends/ix2505v.h
.. kernel-doc:: drivers/media/dvb-frontends/m88ds3103.h
.. kernel-doc:: drivers/media/dvb-frontends/mb86a20s.h
.. kernel-doc:: drivers/media/dvb-frontends/mn88472.h
.. kernel-doc:: drivers/media/dvb-frontends/rtl2830.h
.. kernel-doc:: drivers/media/dvb-frontends/rtl2832.h
.. kernel-doc:: drivers/media/dvb-frontends/rtl2832_sdr.h
.. kernel-doc:: drivers/media/dvb-frontends/stb6000.h
.. kernel-doc:: drivers/media/dvb-frontends/tda10071.h
.. kernel-doc:: drivers/media/dvb-frontends/tda826x.h
.. kernel-doc:: drivers/media/dvb-frontends/zd1301_demod.h
.. kernel-doc:: drivers/media/dvb-frontends/zl10036.h

View File

@ -41,4 +41,5 @@ For more details see the file COPYING in the source distribution of Linux.
technisat
ttusb-dec
udev
frontends
contributors

View File

@ -2901,14 +2901,19 @@ userspace buffer and its length:
struct kvm_s390_irq_state {
__u64 buf;
__u32 flags;
__u32 flags; /* will stay unused for compatibility reasons */
__u32 len;
__u32 reserved[4];
__u32 reserved[4]; /* will stay unused for compatibility reasons */
};
Userspace passes in the above struct and for each pending interrupt a
struct kvm_s390_irq is copied to the provided buffer.
The structure contains a flags and a reserved field for future extensions. As
the kernel never checked for flags == 0 and QEMU never pre-zeroed flags and
reserved, these fields can not be used in the future without breaking
compatibility.
If -ENOBUFS is returned the buffer provided was too small and userspace
may retry with a bigger buffer.
@ -2932,10 +2937,14 @@ containing a struct kvm_s390_irq_state:
struct kvm_s390_irq_state {
__u64 buf;
__u32 flags; /* will stay unused for compatibility reasons */
__u32 len;
__u32 pad;
__u32 reserved[4]; /* will stay unused for compatibility reasons */
};
The restrictions for flags and reserved apply as well.
(see KVM_S390_GET_IRQ_STATE)
The userspace memory referenced by buf contains a struct kvm_s390_irq
for each interrupt to be injected into the guest.
If one of the interrupts could not be injected for some reason the

View File

@ -859,7 +859,8 @@ F: kernel/configs/android*
ANDROID DRIVERS
M: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
M: Arve Hjønnevåg <arve@android.com>
M: Riley Andrews <riandrews@android.com>
M: Todd Kjos <tkjos@android.com>
M: Martijn Coenen <maco@android.com>
T: git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging.git
L: devel@driverdev.osuosl.org
S: Supported
@ -2046,7 +2047,7 @@ F: arch/arm/boot/dts/uniphier*
F: arch/arm/include/asm/hardware/cache-uniphier.h
F: arch/arm/mach-uniphier/
F: arch/arm/mm/cache-uniphier.c
F: arch/arm64/boot/dts/socionext/
F: arch/arm64/boot/dts/socionext/uniphier*
F: drivers/bus/uniphier-system-bus.c
F: drivers/clk/uniphier/
F: drivers/gpio/gpio-uniphier.c
@ -7766,6 +7767,7 @@ F: security/keys/
KGDB / KDB /debug_core
M: Jason Wessel <jason.wessel@windriver.com>
M: Daniel Thompson <daniel.thompson@linaro.org>
W: http://kgdb.wiki.kernel.org/
L: kgdb-bugreport@lists.sourceforge.net
T: git git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb.git
@ -12641,6 +12643,14 @@ S: Maintained
F: drivers/ssb/
F: include/linux/ssb/
SONY IMX274 SENSOR DRIVER
M: Leon Luo <leonl@leopardimaging.com>
L: linux-media@vger.kernel.org
T: git git://linuxtv.org/media_tree.git
S: Maintained
F: drivers/media/i2c/imx274.c
F: Documentation/devicetree/bindings/media/i2c/imx274.txt
SONY MEMORYSTICK CARD SUPPORT
M: Alex Dubov <oakad@yahoo.com>
W: http://tifmxx.berlios.de/

View File

@ -2,7 +2,7 @@
VERSION = 4
PATCHLEVEL = 15
SUBLEVEL = 0
EXTRAVERSION = -rc2
EXTRAVERSION = -rc3
NAME = Fearless Coyote
# *DOCUMENTATION*

View File

@ -1,2 +1,4 @@
# UAPI Header export list
include include/uapi/asm-generic/Kbuild.asm
generic-y += bpf_perf_event.h

View File

@ -3,6 +3,7 @@ include include/uapi/asm-generic/Kbuild.asm
generic-y += auxvec.h
generic-y += bitsperlong.h
generic-y += bpf_perf_event.h
generic-y += errno.h
generic-y += fcntl.h
generic-y += ioctl.h

View File

@ -630,6 +630,7 @@
reg-names = "phy";
status = "disabled";
ti,ctrl_mod = <&usb_ctrl_mod>;
#phy-cells = <0>;
};
usb0: usb@47401000 {
@ -678,6 +679,7 @@
reg-names = "phy";
status = "disabled";
ti,ctrl_mod = <&usb_ctrl_mod>;
#phy-cells = <0>;
};
usb1: usb@47401800 {

View File

@ -927,7 +927,8 @@
reg = <0x48038000 0x2000>,
<0x46000000 0x400000>;
reg-names = "mpu", "dat";
interrupts = <80>, <81>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "tx", "rx";
status = "disabled";
dmas = <&edma 8 2>,
@ -941,7 +942,8 @@
reg = <0x4803C000 0x2000>,
<0x46400000 0x400000>;
reg-names = "mpu", "dat";
interrupts = <82>, <83>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "tx", "rx";
status = "disabled";
dmas = <&edma 10 2>,

View File

@ -301,8 +301,8 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins>;
dmas = <&edma 16
&edma 17>;
dmas = <&edma 16 0
&edma 17 0>;
dma-names = "tx0", "rx0";
flash: w25q64cvzpig@0 {

View File

@ -236,6 +236,7 @@
usb3_phy: usb3_phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&reg_xhci0_vbus>;
#phy-cells = <0>;
};
reg_xhci0_vbus: xhci0-vbus {

View File

@ -66,6 +66,7 @@
usb3_1_phy: usb3_1-phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&usb3_1_vbus>;
#phy-cells = <0>;
};
usb3_1_vbus: usb3_1-vbus {

View File

@ -191,11 +191,13 @@
usb3_0_phy: usb3_0_phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&reg_usb3_0_vbus>;
#phy-cells = <0>;
};
usb3_1_phy: usb3_1_phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&reg_usb3_1_vbus>;
#phy-cells = <0>;
};
reg_usb3_0_vbus: usb3-vbus0 {

View File

@ -276,11 +276,13 @@
usb2_1_phy: usb2_1_phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&reg_usb2_1_vbus>;
#phy-cells = <0>;
};
usb3_phy: usb3_phy {
compatible = "usb-nop-xceiv";
vcc-supply = <&reg_usb3_vbus>;
#phy-cells = <0>;
};
reg_usb3_vbus: usb3-vbus {

View File

@ -85,7 +85,7 @@
timer@20200 {
compatible = "arm,cortex-a9-global-timer";
reg = <0x20200 0x100>;
interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
clocks = <&periph_clk>;
};
@ -93,7 +93,7 @@
compatible = "arm,cortex-a9-twd-timer";
reg = <0x20600 0x20>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
IRQ_TYPE_EDGE_RISING)>;
clocks = <&periph_clk>;
};

View File

@ -639,5 +639,6 @@
usbphy: phy {
compatible = "usb-nop-xceiv";
#phy-cells = <0>;
};
};

View File

@ -141,10 +141,6 @@
status = "okay";
};
&sata {
status = "okay";
};
&qspi {
bspi-sel = <0>;
flash: m25p80@0 {

View File

@ -177,10 +177,6 @@
status = "okay";
};
&sata {
status = "okay";
};
&srab {
compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
status = "okay";

View File

@ -75,6 +75,7 @@
reg = <0x47401300 0x100>;
reg-names = "phy";
ti,ctrl_mod = <&usb_ctrl_mod>;
#phy-cells = <0>;
};
usb0: usb@47401000 {
@ -385,6 +386,7 @@
reg = <0x1b00 0x100>;
reg-names = "phy";
ti,ctrl_mod = <&usb_ctrl_mod>;
#phy-cells = <0>;
};
};

View File

@ -433,15 +433,6 @@
clock-names = "ipg", "per";
};
srtc: srtc@53fa4000 {
compatible = "fsl,imx53-rtc", "fsl,imx25-rtc";
reg = <0x53fa4000 0x4000>;
interrupts = <24>;
interrupt-parent = <&tzic>;
clocks = <&clks IMX5_CLK_SRTC_GATE>;
clock-names = "ipg";
};
iomuxc: iomuxc@53fa8000 {
compatible = "fsl,imx53-iomuxc";
reg = <0x53fa8000 0x4000>;

View File

@ -72,7 +72,8 @@
};
&gpmc {
ranges = <1 0 0x08000000 0x1000000>; /* CS1: 16MB for LAN9221 */
ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */
1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */
ethernet@gpmc {
pinctrl-names = "default";

View File

@ -33,11 +33,12 @@
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
#phy-cells = <0>;
};
};
&gpmc {
ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
nand@0,0 {
compatible = "ti,omap2-nand";
@ -121,7 +122,7 @@
&mmc3 {
interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
pinctrl-0 = <&mmc3_pins>;
pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
pinctrl-names = "default";
vmmc-supply = <&wl12xx_vmmc>;
non-removable;
@ -132,8 +133,8 @@
wlcore: wlcore@2 {
compatible = "ti,wl1273";
reg = <2>;
interrupt-parent = <&gpio5>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
interrupt-parent = <&gpio1>;
interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
ref-clock-frequency = <26000000>;
};
};
@ -157,8 +158,6 @@
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
>;
@ -228,6 +227,12 @@
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
>;
};
wl127x_gpio: pinmux_wl127x_gpio_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */
OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
>;
};
};
&omap3_pmx_core2 {

View File

@ -85,15 +85,6 @@
reg = <0x7c00 0x200>;
};
gpio_intc: interrupt-controller@9880 {
compatible = "amlogic,meson-gpio-intc";
reg = <0xc1109880 0x10>;
interrupt-controller;
#interrupt-cells = <2>;
amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
status = "disabled";
};
hwrng: rng@8100 {
compatible = "amlogic,meson-rng";
reg = <0x8100 0x8>;
@ -191,6 +182,15 @@
status = "disabled";
};
gpio_intc: interrupt-controller@9880 {
compatible = "amlogic,meson-gpio-intc";
reg = <0x9880 0x10>;
interrupt-controller;
#interrupt-cells = <2>;
amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
status = "disabled";
};
wdt: watchdog@9900 {
compatible = "amlogic,meson6-wdt";
reg = <0x9900 0x8>;

View File

@ -56,6 +56,7 @@
usb_phy: usb_phy {
compatible = "usb-nop-xceiv";
#phy-cells = <0>;
};
vbus_reg: vbus_reg {

View File

@ -90,6 +90,7 @@
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
vcc-supply = <&hsusb2_power>;
#phy-cells = <0>;
};
tfp410: encoder0 {

Some files were not shown because too many files have changed in this diff Show More