mirror of
https://github.com/torvalds/linux.git
synced 2024-11-10 22:21:40 +00:00
[MFD] Add code UCB1200/UCB1300 touchscreen support
Add support for Philips UCB1200 and UCB1300 touchscreen interfaces found on ARM devices. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit is contained in:
Russell King
Russell King
parent
05c45ca9aa
commit
acb45439a8
@ -18,4 +18,8 @@ config MCP_UCB1200
|
||||
tristate "Support for UCB1200 / UCB1300"
|
||||
depends on MCP
|
||||
|
||||
config MCP_UCB1200_TS
|
||||
tristate "Touchscreen interface support"
|
||||
depends on MCP_UCB1200 && INPUT
|
||||
|
||||
endmenu
|
||||
|
||||
@ -5,3 +5,4 @@
|
||||
obj-$(CONFIG_MCP) += mcp-core.o
|
||||
obj-$(CONFIG_MCP_SA11X0) += mcp-sa11x0.o
|
||||
obj-$(CONFIG_MCP_UCB1200) += ucb1x00-core.o
|
||||
obj-$(CONFIG_MCP_UCB1200_TS) += ucb1x00-ts.o
|
||||
|
||||
430
drivers/mfd/ucb1x00-ts.c
Normal file
430
drivers/mfd/ucb1x00-ts.c
Normal file
@ -0,0 +1,430 @@
|
||||
/*
|
||||
* linux/drivers/mfd/ucb1x00-ts.c
|
||||
*
|
||||
* Copyright (C) 2001 Russell King, All Rights Reserved.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*
|
||||
* 21-Jan-2002 <jco@ict.es> :
|
||||
*
|
||||
* Added support for synchronous A/D mode. This mode is useful to
|
||||
* avoid noise induced in the touchpanel by the LCD, provided that
|
||||
* the UCB1x00 has a valid LCD sync signal routed to its ADCSYNC pin.
|
||||
* It is important to note that the signal connected to the ADCSYNC
|
||||
* pin should provide pulses even when the LCD is blanked, otherwise
|
||||
* a pen touch needed to unblank the LCD will never be read.
|
||||
*/
|
||||
#include <linux/config.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/moduleparam.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/smp.h>
|
||||
#include <linux/smp_lock.h>
|
||||
#include <linux/sched.h>
|
||||
#include <linux/completion.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/string.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/device.h>
|
||||
#include <linux/suspend.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
#include <asm/dma.h>
|
||||
#include <asm/semaphore.h>
|
||||
|
||||
#include "ucb1x00.h"
|
||||
|
||||
|
||||
struct ucb1x00_ts {
|
||||
struct input_dev idev;
|
||||
struct ucb1x00 *ucb;
|
||||
|
||||
wait_queue_head_t irq_wait;
|
||||
struct semaphore sem;
|
||||
struct completion init_exit;
|
||||
struct task_struct *rtask;
|
||||
int use_count;
|
||||
u16 x_res;
|
||||
u16 y_res;
|
||||
|
||||
int restart:1;
|
||||
int adcsync:1;
|
||||
};
|
||||
|
||||
static int adcsync;
|
||||
|
||||
static inline void ucb1x00_ts_evt_add(struct ucb1x00_ts *ts, u16 pressure, u16 x, u16 y)
|
||||
{
|
||||
input_report_abs(&ts->idev, ABS_X, x);
|
||||
input_report_abs(&ts->idev, ABS_Y, y);
|
||||
input_report_abs(&ts->idev, ABS_PRESSURE, pressure);
|
||||
input_sync(&ts->idev);
|
||||
}
|
||||
|
||||
static inline void ucb1x00_ts_event_release(struct ucb1x00_ts *ts)
|
||||
{
|
||||
input_report_abs(&ts->idev, ABS_PRESSURE, 0);
|
||||
input_sync(&ts->idev);
|
||||
}
|
||||
|
||||
/*
|
||||
* Switch to interrupt mode.
|
||||
*/
|
||||
static inline void ucb1x00_ts_mode_int(struct ucb1x00_ts *ts)
|
||||
{
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMX_POW | UCB_TS_CR_TSPX_POW |
|
||||
UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_GND |
|
||||
UCB_TS_CR_MODE_INT);
|
||||
}
|
||||
|
||||
/*
|
||||
* Switch to pressure mode, and read pressure. We don't need to wait
|
||||
* here, since both plates are being driven.
|
||||
*/
|
||||
static inline unsigned int ucb1x00_ts_read_pressure(struct ucb1x00_ts *ts)
|
||||
{
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMX_POW | UCB_TS_CR_TSPX_POW |
|
||||
UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_GND |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
|
||||
return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_TSPY, ts->adcsync);
|
||||
}
|
||||
|
||||
/*
|
||||
* Switch to X position mode and measure Y plate. We switch the plate
|
||||
* configuration in pressure mode, then switch to position mode. This
|
||||
* gives a faster response time. Even so, we need to wait about 55us
|
||||
* for things to stabilise.
|
||||
*/
|
||||
static inline unsigned int ucb1x00_ts_read_xpos(struct ucb1x00_ts *ts)
|
||||
{
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
|
||||
UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA);
|
||||
|
||||
udelay(55);
|
||||
|
||||
return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_TSPY, ts->adcsync);
|
||||
}
|
||||
|
||||
/*
|
||||
* Switch to Y position mode and measure X plate. We switch the plate
|
||||
* configuration in pressure mode, then switch to position mode. This
|
||||
* gives a faster response time. Even so, we need to wait about 55us
|
||||
* for things to stabilise.
|
||||
*/
|
||||
static inline unsigned int ucb1x00_ts_read_ypos(struct ucb1x00_ts *ts)
|
||||
{
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
|
||||
UCB_TS_CR_MODE_POS | UCB_TS_CR_BIAS_ENA);
|
||||
|
||||
udelay(55);
|
||||
|
||||
return ucb1x00_adc_read(ts->ucb, UCB_ADC_INP_TSPX, ts->adcsync);
|
||||
}
|
||||
|
||||
/*
|
||||
* Switch to X plate resistance mode. Set MX to ground, PX to
|
||||
* supply. Measure current.
|
||||
*/
|
||||
static inline unsigned int ucb1x00_ts_read_xres(struct ucb1x00_ts *ts)
|
||||
{
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMX_GND | UCB_TS_CR_TSPX_POW |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
return ucb1x00_adc_read(ts->ucb, 0, ts->adcsync);
|
||||
}
|
||||
|
||||
/*
|
||||
* Switch to Y plate resistance mode. Set MY to ground, PY to
|
||||
* supply. Measure current.
|
||||
*/
|
||||
static inline unsigned int ucb1x00_ts_read_yres(struct ucb1x00_ts *ts)
|
||||
{
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR,
|
||||
UCB_TS_CR_TSMY_GND | UCB_TS_CR_TSPY_POW |
|
||||
UCB_TS_CR_MODE_PRES | UCB_TS_CR_BIAS_ENA);
|
||||
return ucb1x00_adc_read(ts->ucb, 0, ts->adcsync);
|
||||
}
|
||||
|
||||
/*
|
||||
* This is a RT kernel thread that handles the ADC accesses
|
||||
* (mainly so we can use semaphores in the UCB1200 core code
|
||||
* to serialise accesses to the ADC).
|
||||
*/
|
||||
static int ucb1x00_thread(void *_ts)
|
||||
{
|
||||
struct ucb1x00_ts *ts = _ts;
|
||||
struct task_struct *tsk = current;
|
||||
DECLARE_WAITQUEUE(wait, tsk);
|
||||
int valid;
|
||||
|
||||
ts->rtask = tsk;
|
||||
|
||||
daemonize("ktsd");
|
||||
/* only want to receive SIGKILL */
|
||||
allow_signal(SIGKILL);
|
||||
|
||||
/*
|
||||
* We could run as a real-time thread. However, thus far
|
||||
* this doesn't seem to be necessary.
|
||||
*/
|
||||
// tsk->policy = SCHED_FIFO;
|
||||
// tsk->rt_priority = 1;
|
||||
|
||||
complete(&ts->init_exit);
|
||||
|
||||
valid = 0;
|
||||
|
||||
add_wait_queue(&ts->irq_wait, &wait);
|
||||
for (;;) {
|
||||
unsigned int x, y, p, val;
|
||||
signed long timeout;
|
||||
|
||||
ts->restart = 0;
|
||||
|
||||
ucb1x00_adc_enable(ts->ucb);
|
||||
|
||||
x = ucb1x00_ts_read_xpos(ts);
|
||||
y = ucb1x00_ts_read_ypos(ts);
|
||||
p = ucb1x00_ts_read_pressure(ts);
|
||||
|
||||
/*
|
||||
* Switch back to interrupt mode.
|
||||
*/
|
||||
ucb1x00_ts_mode_int(ts);
|
||||
ucb1x00_adc_disable(ts->ucb);
|
||||
|
||||
set_task_state(tsk, TASK_UNINTERRUPTIBLE);
|
||||
schedule_timeout(HZ / 100);
|
||||
if (signal_pending(tsk))
|
||||
break;
|
||||
|
||||
ucb1x00_enable(ts->ucb);
|
||||
val = ucb1x00_reg_read(ts->ucb, UCB_TS_CR);
|
||||
|
||||
if (val & (UCB_TS_CR_TSPX_LOW | UCB_TS_CR_TSMX_LOW)) {
|
||||
set_task_state(tsk, TASK_INTERRUPTIBLE);
|
||||
|
||||
ucb1x00_enable_irq(ts->ucb, UCB_IRQ_TSPX, UCB_FALLING);
|
||||
ucb1x00_disable(ts->ucb);
|
||||
|
||||
/*
|
||||
* If we spat out a valid sample set last time,
|
||||
* spit out a "pen off" sample here.
|
||||
*/
|
||||
if (valid) {
|
||||
ucb1x00_ts_event_release(ts);
|
||||
valid = 0;
|
||||
}
|
||||
|
||||
timeout = MAX_SCHEDULE_TIMEOUT;
|
||||
} else {
|
||||
ucb1x00_disable(ts->ucb);
|
||||
|
||||
/*
|
||||
* Filtering is policy. Policy belongs in user
|
||||
* space. We therefore leave it to user space
|
||||
* to do any filtering they please.
|
||||
*/
|
||||
if (!ts->restart) {
|
||||
ucb1x00_ts_evt_add(ts, p, x, y);
|
||||
valid = 1;
|
||||
}
|
||||
|
||||
set_task_state(tsk, TASK_INTERRUPTIBLE);
|
||||
timeout = HZ / 100;
|
||||
}
|
||||
|
||||
try_to_freeze();
|
||||
|
||||
schedule_timeout(timeout);
|
||||
if (signal_pending(tsk))
|
||||
break;
|
||||
}
|
||||
|
||||
remove_wait_queue(&ts->irq_wait, &wait);
|
||||
|
||||
ts->rtask = NULL;
|
||||
complete_and_exit(&ts->init_exit, 0);
|
||||
}
|
||||
|
||||
/*
|
||||
* We only detect touch screen _touches_ with this interrupt
|
||||
* handler, and even then we just schedule our task.
|
||||
*/
|
||||
static void ucb1x00_ts_irq(int idx, void *id)
|
||||
{
|
||||
struct ucb1x00_ts *ts = id;
|
||||
ucb1x00_disable_irq(ts->ucb, UCB_IRQ_TSPX, UCB_FALLING);
|
||||
wake_up(&ts->irq_wait);
|
||||
}
|
||||
|
||||
static int ucb1x00_ts_open(struct input_dev *idev)
|
||||
{
|
||||
struct ucb1x00_ts *ts = (struct ucb1x00_ts *)idev;
|
||||
int ret = 0;
|
||||
|
||||
if (down_interruptible(&ts->sem))
|
||||
return -EINTR;
|
||||
|
||||
if (ts->use_count++ != 0)
|
||||
goto out;
|
||||
|
||||
if (ts->rtask)
|
||||
panic("ucb1x00: rtask running?");
|
||||
|
||||
init_waitqueue_head(&ts->irq_wait);
|
||||
ret = ucb1x00_hook_irq(ts->ucb, UCB_IRQ_TSPX, ucb1x00_ts_irq, ts);
|
||||
if (ret < 0)
|
||||
goto out;
|
||||
|
||||
/*
|
||||
* If we do this at all, we should allow the user to
|
||||
* measure and read the X and Y resistance at any time.
|
||||
*/
|
||||
ucb1x00_adc_enable(ts->ucb);
|
||||
ts->x_res = ucb1x00_ts_read_xres(ts);
|
||||
ts->y_res = ucb1x00_ts_read_yres(ts);
|
||||
ucb1x00_adc_disable(ts->ucb);
|
||||
|
||||
init_completion(&ts->init_exit);
|
||||
ret = kernel_thread(ucb1x00_thread, ts, CLONE_KERNEL);
|
||||
if (ret >= 0) {
|
||||
wait_for_completion(&ts->init_exit);
|
||||
ret = 0;
|
||||
} else {
|
||||
ucb1x00_free_irq(ts->ucb, UCB_IRQ_TSPX, ts);
|
||||
}
|
||||
|
||||
out:
|
||||
if (ret)
|
||||
ts->use_count--;
|
||||
up(&ts->sem);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/*
|
||||
* Release touchscreen resources. Disable IRQs.
|
||||
*/
|
||||
static void ucb1x00_ts_close(struct input_dev *idev)
|
||||
{
|
||||
struct ucb1x00_ts *ts = (struct ucb1x00_ts *)idev;
|
||||
|
||||
down(&ts->sem);
|
||||
if (--ts->use_count == 0) {
|
||||
if (ts->rtask) {
|
||||
send_sig(SIGKILL, ts->rtask, 1);
|
||||
wait_for_completion(&ts->init_exit);
|
||||
}
|
||||
|
||||
ucb1x00_enable(ts->ucb);
|
||||
ucb1x00_free_irq(ts->ucb, UCB_IRQ_TSPX, ts);
|
||||
ucb1x00_reg_write(ts->ucb, UCB_TS_CR, 0);
|
||||
ucb1x00_disable(ts->ucb);
|
||||
}
|
||||
up(&ts->sem);
|
||||
}
|
||||
|
||||
#ifdef CONFIG_PM
|
||||
static int ucb1x00_ts_resume(struct ucb1x00_dev *dev)
|
||||
{
|
||||
struct ucb1x00_ts *ts = dev->priv;
|
||||
|
||||
if (ts->rtask != NULL) {
|
||||
/*
|
||||
* Restart the TS thread to ensure the
|
||||
* TS interrupt mode is set up again
|
||||
* after sleep.
|
||||
*/
|
||||
ts->restart = 1;
|
||||
wake_up(&ts->irq_wait);
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
#else
|
||||
#define ucb1x00_ts_resume NULL
|
||||
#endif
|
||||
|
||||
|
||||
/*
|
||||
* Initialisation.
|
||||
*/
|
||||
static int ucb1x00_ts_add(struct ucb1x00_dev *dev)
|
||||
{
|
||||
struct ucb1x00_ts *ts;
|
||||
|
||||
ts = kmalloc(sizeof(struct ucb1x00_ts), GFP_KERNEL);
|
||||
if (!ts)
|
||||
return -ENOMEM;
|
||||
|
||||
memset(ts, 0, sizeof(struct ucb1x00_ts));
|
||||
|
||||
ts->ucb = dev->ucb;
|
||||
ts->adcsync = adcsync ? UCB_SYNC : UCB_NOSYNC;
|
||||
init_MUTEX(&ts->sem);
|
||||
|
||||
ts->idev.name = "Touchscreen panel";
|
||||
ts->idev.id.product = ts->ucb->id;
|
||||
ts->idev.open = ucb1x00_ts_open;
|
||||
ts->idev.close = ucb1x00_ts_close;
|
||||
|
||||
__set_bit(EV_ABS, ts->idev.evbit);
|
||||
__set_bit(ABS_X, ts->idev.absbit);
|
||||
__set_bit(ABS_Y, ts->idev.absbit);
|
||||
__set_bit(ABS_PRESSURE, ts->idev.absbit);
|
||||
|
||||
input_register_device(&ts->idev);
|
||||
|
||||
dev->priv = ts;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void ucb1x00_ts_remove(struct ucb1x00_dev *dev)
|
||||
{
|
||||
struct ucb1x00_ts *ts = dev->priv;
|
||||
input_unregister_device(&ts->idev);
|
||||
kfree(ts);
|
||||
}
|
||||
|
||||
static struct ucb1x00_driver ucb1x00_ts_driver = {
|
||||
.add = ucb1x00_ts_add,
|
||||
.remove = ucb1x00_ts_remove,
|
||||
.resume = ucb1x00_ts_resume,
|
||||
};
|
||||
|
||||
static int __init ucb1x00_ts_init(void)
|
||||
{
|
||||
return ucb1x00_register_driver(&ucb1x00_ts_driver);
|
||||
}
|
||||
|
||||
static void __exit ucb1x00_ts_exit(void)
|
||||
{
|
||||
ucb1x00_unregister_driver(&ucb1x00_ts_driver);
|
||||
}
|
||||
|
||||
module_param(adcsync, int, 0444);
|
||||
module_init(ucb1x00_ts_init);
|
||||
module_exit(ucb1x00_ts_exit);
|
||||
|
||||
MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
|
||||
MODULE_DESCRIPTION("UCB1x00 touchscreen driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
Loading…
Reference in New Issue
Block a user