From 9b5db7aab4d6b66f84f5e147c87eff4fe8b48651 Mon Sep 17 00:00:00 2001 From: Paul Cercueil Date: Fri, 13 Oct 2017 11:04:48 -0700 Subject: [PATCH] Input: goodix - poll the 'buffer status' bit before reading data The Goodix panel triggers an interrupt on touch events. However, its registers will contain the valid values a short time after the interrupt, and not when it's raised. At that moment, the 'buffer status' bit is set. Previously, if the 'buffer status' bit was not set when the registers were read, the data was discarded and no input event was emitted, causing "finger down" or "finger up" events to be missed sometimes. This went unnoticed until v4.9, as the DesignWare I2C driver commonly used with this driver had enough latency for that bug to never trigger until commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only if necessary"). Now, in the IRQ handler we will poll (with a timeout) the 'buffer status' bit and process the data of the panel as soon as this bit gets set. Note that the Goodix panel will send a few spurious interrupts after the 'finger up' event, in which the 'buffer status' bit will never be set. Cc: Bastien Nocera Cc: russianneuromancer@ya.ru Signed-off-by: Paul Cercueil [hdegoede@redhat.com: Change poll loop to use jiffies, add comment about typical poll time] Signed-off-by: Hans de Goede [dtor: rearranged control flow a bit to avoid explicit goto and double check] Reviewed-by: Bastien Nocera Signed-off-by: Dmitry Torokhov --- drivers/input/touchscreen/goodix.c | 69 +++++++++++++++++++----------- 1 file changed, 45 insertions(+), 24 deletions(-) diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c index 32d2762448aa..b3bbad7d2282 100644 --- a/drivers/input/touchscreen/goodix.c +++ b/drivers/input/touchscreen/goodix.c @@ -72,6 +72,9 @@ struct goodix_ts_data { #define GOODIX_REG_CONFIG_DATA 0x8047 #define GOODIX_REG_ID 0x8140 +#define GOODIX_BUFFER_STATUS_READY BIT(7) +#define GOODIX_BUFFER_STATUS_TIMEOUT 20 + #define RESOLUTION_LOC 1 #define MAX_CONTACTS_LOC 5 #define TRIGGER_LOC 6 @@ -195,35 +198,53 @@ static int goodix_get_cfg_len(u16 id) static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data) { + unsigned long max_timeout; int touch_num; int error; - error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR, data, - GOODIX_CONTACT_SIZE + 1); - if (error) { - dev_err(&ts->client->dev, "I2C transfer error: %d\n", error); - return error; - } - - if (!(data[0] & 0x80)) - return -EAGAIN; - - touch_num = data[0] & 0x0f; - if (touch_num > ts->max_touch_num) - return -EPROTO; - - if (touch_num > 1) { - data += 1 + GOODIX_CONTACT_SIZE; - error = goodix_i2c_read(ts->client, - GOODIX_READ_COOR_ADDR + - 1 + GOODIX_CONTACT_SIZE, - data, - GOODIX_CONTACT_SIZE * (touch_num - 1)); - if (error) + /* + * The 'buffer status' bit, which indicates that the data is valid, is + * not set as soon as the interrupt is raised, but slightly after. + * This takes around 10 ms to happen, so we poll for 20 ms. + */ + max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT); + do { + error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR, + data, GOODIX_CONTACT_SIZE + 1); + if (error) { + dev_err(&ts->client->dev, "I2C transfer error: %d\n", + error); return error; - } + } - return touch_num; + if (data[0] & GOODIX_BUFFER_STATUS_READY) { + touch_num = data[0] & 0x0f; + if (touch_num > ts->max_touch_num) + return -EPROTO; + + if (touch_num > 1) { + data += 1 + GOODIX_CONTACT_SIZE; + error = goodix_i2c_read(ts->client, + GOODIX_READ_COOR_ADDR + + 1 + GOODIX_CONTACT_SIZE, + data, + GOODIX_CONTACT_SIZE * + (touch_num - 1)); + if (error) + return error; + } + + return touch_num; + } + + usleep_range(1000, 2000); /* Poll every 1 - 2 ms */ + } while (time_before(jiffies, max_timeout)); + + /* + * The Goodix panel will send spurious interrupts after a + * 'finger up' event, which will always cause a timeout. + */ + return 0; } static void goodix_ts_report_touch(struct goodix_ts_data *ts, u8 *coor_data)