From 8bfd4858b4bba8fec14e4296cbac71aa55260d60 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Wed, 17 Nov 2021 21:18:41 -0600 Subject: [PATCH 1/8] PM / devfreq: Add a driver for the sun8i/sun50i MBUS This driver works by adjusting the divider on the DRAM controller's module clock. Thus there is no fixed set of OPPs, only "full speed" down to "quarter speed" (or whatever the maximum divider is on that variant). It makes use of the MDFS hardware in the MBUS, in "DFS" mode, which takes care of updating registers during the critical section while DRAM is inaccessible. This driver should support several sunxi SoCs, starting with the A33, which have a DesignWare DDR3 controller with merged PHY register space and the matching MBUS register layout (so not A63 or later). However, the driver has only been tested on the A64/H5, so those are the only compatibles enabled for now. Acked-by: Chanwoo Choi Signed-off-by: Samuel Holland Signed-off-by: Chanwoo Choi --- drivers/devfreq/Kconfig | 8 + drivers/devfreq/Makefile | 1 + drivers/devfreq/sun8i-a33-mbus.c | 511 +++++++++++++++++++++++++++++++ 3 files changed, 520 insertions(+) create mode 100644 drivers/devfreq/sun8i-a33-mbus.c diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig index e87d01c0b76a..b94eb04761f6 100644 --- a/drivers/devfreq/Kconfig +++ b/drivers/devfreq/Kconfig @@ -132,6 +132,14 @@ config ARM_RK3399_DMC_DEVFREQ It sets the frequency for the memory controller and reads the usage counts from hardware. +config ARM_SUN8I_A33_MBUS_DEVFREQ + tristate "sun8i/sun50i MBUS DEVFREQ Driver" + depends on ARCH_SUNXI || COMPILE_TEST + select DEVFREQ_GOV_SIMPLE_ONDEMAND + help + This adds the DEVFREQ driver for the MBUS controller in some + Allwinner sun8i (A33 through H3) and sun50i (A64 and H5) SoCs. + source "drivers/devfreq/event/Kconfig" endif # PM_DEVFREQ diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile index a16333ea7034..0b6be92a25d9 100644 --- a/drivers/devfreq/Makefile +++ b/drivers/devfreq/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ) += exynos-bus.o obj-$(CONFIG_ARM_IMX_BUS_DEVFREQ) += imx-bus.o obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ) += imx8m-ddrc.o obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ) += rk3399_dmc.o +obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ) += sun8i-a33-mbus.o obj-$(CONFIG_ARM_TEGRA_DEVFREQ) += tegra30-devfreq.o # DEVFREQ Event Drivers diff --git a/drivers/devfreq/sun8i-a33-mbus.c b/drivers/devfreq/sun8i-a33-mbus.c new file mode 100644 index 000000000000..13d32213139f --- /dev/null +++ b/drivers/devfreq/sun8i-a33-mbus.c @@ -0,0 +1,511 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// Copyright (C) 2020-2021 Samuel Holland +// + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define MBUS_CR 0x0000 +#define MBUS_CR_GET_DRAM_TYPE(x) (((x) >> 16) & 0x7) +#define MBUS_CR_DRAM_TYPE_DDR2 2 +#define MBUS_CR_DRAM_TYPE_DDR3 3 +#define MBUS_CR_DRAM_TYPE_DDR4 4 +#define MBUS_CR_DRAM_TYPE_LPDDR2 6 +#define MBUS_CR_DRAM_TYPE_LPDDR3 7 + +#define MBUS_TMR 0x000c +#define MBUS_TMR_PERIOD(x) ((x) - 1) + +#define MBUS_PMU_CFG 0x009c +#define MBUS_PMU_CFG_PERIOD(x) (((x) - 1) << 16) +#define MBUS_PMU_CFG_UNIT (0x3 << 1) +#define MBUS_PMU_CFG_UNIT_B (0x0 << 1) +#define MBUS_PMU_CFG_UNIT_KB (0x1 << 1) +#define MBUS_PMU_CFG_UNIT_MB (0x2 << 1) +#define MBUS_PMU_CFG_ENABLE (0x1 << 0) + +#define MBUS_PMU_BWCR(n) (0x00a0 + (0x04 * (n))) + +#define MBUS_TOTAL_BWCR MBUS_PMU_BWCR(5) +#define MBUS_TOTAL_BWCR_H616 MBUS_PMU_BWCR(13) + +#define MBUS_MDFSCR 0x0100 +#define MBUS_MDFSCR_BUFFER_TIMING (0x1 << 15) +#define MBUS_MDFSCR_PAD_HOLD (0x1 << 13) +#define MBUS_MDFSCR_BYPASS (0x1 << 4) +#define MBUS_MDFSCR_MODE (0x1 << 1) +#define MBUS_MDFSCR_MODE_DFS (0x0 << 1) +#define MBUS_MDFSCR_MODE_CFS (0x1 << 1) +#define MBUS_MDFSCR_START (0x1 << 0) + +#define MBUS_MDFSMRMR 0x0108 + +#define DRAM_PWRCTL 0x0004 +#define DRAM_PWRCTL_SELFREF_EN (0x1 << 0) + +#define DRAM_RFSHTMG 0x0090 +#define DRAM_RFSHTMG_TREFI(x) ((x) << 16) +#define DRAM_RFSHTMG_TRFC(x) ((x) << 0) + +#define DRAM_VTFCR 0x00b8 +#define DRAM_VTFCR_VTF_ENABLE (0x3 << 8) + +#define DRAM_ODTMAP 0x0120 + +#define DRAM_DX_MAX 4 + +#define DRAM_DXnGCR0(n) (0x0344 + 0x80 * (n)) +#define DRAM_DXnGCR0_DXODT (0x3 << 4) +#define DRAM_DXnGCR0_DXODT_DYNAMIC (0x0 << 4) +#define DRAM_DXnGCR0_DXODT_ENABLED (0x1 << 4) +#define DRAM_DXnGCR0_DXODT_DISABLED (0x2 << 4) +#define DRAM_DXnGCR0_DXEN (0x1 << 0) + +struct sun8i_a33_mbus_variant { + u32 min_dram_divider; + u32 max_dram_divider; + u32 odt_freq_mhz; +}; + +struct sun8i_a33_mbus { + const struct sun8i_a33_mbus_variant *variant; + void __iomem *reg_dram; + void __iomem *reg_mbus; + struct clk *clk_bus; + struct clk *clk_dram; + struct clk *clk_mbus; + struct devfreq *devfreq_dram; + struct devfreq_simple_ondemand_data gov_data; + struct devfreq_dev_profile profile; + u32 data_width; + u32 nominal_bw; + u32 odtmap; + u32 tREFI_ns; + u32 tRFC_ns; + unsigned long freq_table[]; +}; + +/* + * The unit for this value is (MBUS clock cycles / MBUS_TMR_PERIOD). When + * MBUS_TMR_PERIOD is programmed to match the MBUS clock frequency in MHz, as + * it is during DRAM init and during probe, the resulting unit is microseconds. + */ +static int pmu_period = 50000; +module_param(pmu_period, int, 0644); +MODULE_PARM_DESC(pmu_period, "Bandwidth measurement period (microseconds)"); + +static u32 sun8i_a33_mbus_get_peak_bw(struct sun8i_a33_mbus *priv) +{ + /* Returns the peak transfer (in KiB) during any single PMU period. */ + return readl_relaxed(priv->reg_mbus + MBUS_TOTAL_BWCR); +} + +static void sun8i_a33_mbus_restart_pmu_counters(struct sun8i_a33_mbus *priv) +{ + u32 pmu_cfg = MBUS_PMU_CFG_PERIOD(pmu_period) | MBUS_PMU_CFG_UNIT_KB; + + /* All PMU counters are cleared on a disable->enable transition. */ + writel_relaxed(pmu_cfg, + priv->reg_mbus + MBUS_PMU_CFG); + writel_relaxed(pmu_cfg | MBUS_PMU_CFG_ENABLE, + priv->reg_mbus + MBUS_PMU_CFG); + +} + +static void sun8i_a33_mbus_update_nominal_bw(struct sun8i_a33_mbus *priv, + u32 ddr_freq_mhz) +{ + /* + * Nominal bandwidth (KiB per PMU period): + * + * DDR transfers microseconds KiB + * ------------- * ------------ * -------- + * microsecond PMU period transfer + */ + priv->nominal_bw = ddr_freq_mhz * pmu_period * priv->data_width / 1024; +} + +static int sun8i_a33_mbus_set_dram_freq(struct sun8i_a33_mbus *priv, + unsigned long freq) +{ + u32 ddr_freq_mhz = freq / USEC_PER_SEC; /* DDR */ + u32 dram_freq_mhz = ddr_freq_mhz / 2; /* SDR */ + u32 mctl_freq_mhz = dram_freq_mhz / 2; /* HDR */ + u32 dxodt, mdfscr, pwrctl, vtfcr; + u32 i, tREFI_32ck, tRFC_ck; + int ret; + + /* The rate change is not effective until the MDFS process runs. */ + ret = clk_set_rate(priv->clk_dram, freq); + if (ret) + return ret; + + /* Disable automatic self-refesh and VTF before starting MDFS. */ + pwrctl = readl_relaxed(priv->reg_dram + DRAM_PWRCTL) & + ~DRAM_PWRCTL_SELFREF_EN; + writel_relaxed(pwrctl, priv->reg_dram + DRAM_PWRCTL); + vtfcr = readl_relaxed(priv->reg_dram + DRAM_VTFCR); + writel_relaxed(vtfcr & ~DRAM_VTFCR_VTF_ENABLE, + priv->reg_dram + DRAM_VTFCR); + + /* Set up MDFS and enable double buffering for timing registers. */ + mdfscr = MBUS_MDFSCR_MODE_DFS | + MBUS_MDFSCR_BYPASS | + MBUS_MDFSCR_PAD_HOLD | + MBUS_MDFSCR_BUFFER_TIMING; + writel(mdfscr, priv->reg_mbus + MBUS_MDFSCR); + + /* Update the buffered copy of RFSHTMG. */ + tREFI_32ck = priv->tREFI_ns * mctl_freq_mhz / 1000 / 32; + tRFC_ck = DIV_ROUND_UP(priv->tRFC_ns * mctl_freq_mhz, 1000); + writel(DRAM_RFSHTMG_TREFI(tREFI_32ck) | DRAM_RFSHTMG_TRFC(tRFC_ck), + priv->reg_dram + DRAM_RFSHTMG); + + /* Enable ODT if needed, or disable it to save power. */ + if (priv->odtmap && dram_freq_mhz > priv->variant->odt_freq_mhz) { + dxodt = DRAM_DXnGCR0_DXODT_DYNAMIC; + writel(priv->odtmap, priv->reg_dram + DRAM_ODTMAP); + } else { + dxodt = DRAM_DXnGCR0_DXODT_DISABLED; + writel(0, priv->reg_dram + DRAM_ODTMAP); + } + for (i = 0; i < DRAM_DX_MAX; ++i) { + void __iomem *reg = priv->reg_dram + DRAM_DXnGCR0(i); + + writel((readl(reg) & ~DRAM_DXnGCR0_DXODT) | dxodt, reg); + } + + dev_dbg(priv->devfreq_dram->dev.parent, + "Setting DRAM to %u MHz, tREFI=%u, tRFC=%u, ODT=%s\n", + dram_freq_mhz, tREFI_32ck, tRFC_ck, + dxodt == DRAM_DXnGCR0_DXODT_DYNAMIC ? "dynamic" : "disabled"); + + /* Trigger hardware MDFS. */ + writel(mdfscr | MBUS_MDFSCR_START, priv->reg_mbus + MBUS_MDFSCR); + ret = readl_poll_timeout_atomic(priv->reg_mbus + MBUS_MDFSCR, mdfscr, + !(mdfscr & MBUS_MDFSCR_START), 10, 1000); + if (ret) + return ret; + + /* Disable double buffering. */ + writel(0, priv->reg_mbus + MBUS_MDFSCR); + + /* Restore VTF configuration. */ + writel_relaxed(vtfcr, priv->reg_dram + DRAM_VTFCR); + + /* Enable automatic self-refresh at the lowest frequency only. */ + if (freq == priv->freq_table[0]) + pwrctl |= DRAM_PWRCTL_SELFREF_EN; + writel_relaxed(pwrctl, priv->reg_dram + DRAM_PWRCTL); + + sun8i_a33_mbus_restart_pmu_counters(priv); + sun8i_a33_mbus_update_nominal_bw(priv, ddr_freq_mhz); + + return 0; +} + +static int sun8i_a33_mbus_set_dram_target(struct device *dev, + unsigned long *freq, u32 flags) +{ + struct sun8i_a33_mbus *priv = dev_get_drvdata(dev); + struct devfreq *devfreq = priv->devfreq_dram; + struct dev_pm_opp *opp; + int ret; + + opp = devfreq_recommended_opp(dev, freq, flags); + if (IS_ERR(opp)) + return PTR_ERR(opp); + + dev_pm_opp_put(opp); + + if (*freq == devfreq->previous_freq) + return 0; + + ret = sun8i_a33_mbus_set_dram_freq(priv, *freq); + if (ret) { + dev_warn(dev, "failed to set DRAM frequency: %d\n", ret); + *freq = devfreq->previous_freq; + } + + return ret; +} + +static int sun8i_a33_mbus_get_dram_status(struct device *dev, + struct devfreq_dev_status *stat) +{ + struct sun8i_a33_mbus *priv = dev_get_drvdata(dev); + + stat->busy_time = sun8i_a33_mbus_get_peak_bw(priv); + stat->total_time = priv->nominal_bw; + stat->current_frequency = priv->devfreq_dram->previous_freq; + + sun8i_a33_mbus_restart_pmu_counters(priv); + + dev_dbg(dev, "Using %lu/%lu (%lu%%) at %lu MHz\n", + stat->busy_time, stat->total_time, + DIV_ROUND_CLOSEST(stat->busy_time * 100, stat->total_time), + stat->current_frequency / USEC_PER_SEC); + + return 0; +} + +static int sun8i_a33_mbus_hw_init(struct device *dev, + struct sun8i_a33_mbus *priv, + unsigned long ddr_freq) +{ + u32 i, mbus_cr, mbus_freq_mhz; + + /* Choose tREFI and tRFC to match the configured DRAM type. */ + mbus_cr = readl_relaxed(priv->reg_mbus + MBUS_CR); + switch (MBUS_CR_GET_DRAM_TYPE(mbus_cr)) { + case MBUS_CR_DRAM_TYPE_DDR2: + case MBUS_CR_DRAM_TYPE_DDR3: + case MBUS_CR_DRAM_TYPE_DDR4: + priv->tREFI_ns = 7800; + priv->tRFC_ns = 350; + break; + case MBUS_CR_DRAM_TYPE_LPDDR2: + case MBUS_CR_DRAM_TYPE_LPDDR3: + priv->tREFI_ns = 3900; + priv->tRFC_ns = 210; + break; + default: + return -EINVAL; + } + + /* Save ODTMAP so it can be restored when raising the frequency. */ + priv->odtmap = readl_relaxed(priv->reg_dram + DRAM_ODTMAP); + + /* Compute the DRAM data bus width by counting enabled DATx8 blocks. */ + for (i = 0; i < DRAM_DX_MAX; ++i) { + void __iomem *reg = priv->reg_dram + DRAM_DXnGCR0(i); + + if (!(readl_relaxed(reg) & DRAM_DXnGCR0_DXEN)) + break; + } + priv->data_width = i; + + dev_dbg(dev, "Detected %u-bit %sDDRx with%s ODT\n", + priv->data_width * 8, + MBUS_CR_GET_DRAM_TYPE(mbus_cr) > 4 ? "LP" : "", + priv->odtmap ? "" : "out"); + + /* Program MBUS_TMR such that the PMU period unit is microseconds. */ + mbus_freq_mhz = clk_get_rate(priv->clk_mbus) / USEC_PER_SEC; + writel_relaxed(MBUS_TMR_PERIOD(mbus_freq_mhz), + priv->reg_mbus + MBUS_TMR); + + /* "Master Ready Mask Register" bits must be set or MDFS will block. */ + writel_relaxed(0xffffffff, priv->reg_mbus + MBUS_MDFSMRMR); + + sun8i_a33_mbus_restart_pmu_counters(priv); + sun8i_a33_mbus_update_nominal_bw(priv, ddr_freq / USEC_PER_SEC); + + return 0; +} + +static int __maybe_unused sun8i_a33_mbus_suspend(struct device *dev) +{ + struct sun8i_a33_mbus *priv = dev_get_drvdata(dev); + + clk_disable_unprepare(priv->clk_bus); + + return 0; +} + +static int __maybe_unused sun8i_a33_mbus_resume(struct device *dev) +{ + struct sun8i_a33_mbus *priv = dev_get_drvdata(dev); + + return clk_prepare_enable(priv->clk_bus); +} + +static int sun8i_a33_mbus_probe(struct platform_device *pdev) +{ + const struct sun8i_a33_mbus_variant *variant; + struct device *dev = &pdev->dev; + struct sun8i_a33_mbus *priv; + unsigned long base_freq; + unsigned int max_state; + const char *err; + int i, ret; + + variant = device_get_match_data(dev); + if (!variant) + return -EINVAL; + + max_state = variant->max_dram_divider - variant->min_dram_divider + 1; + + priv = devm_kzalloc(dev, struct_size(priv, freq_table, max_state), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + platform_set_drvdata(pdev, priv); + + priv->variant = variant; + + priv->reg_dram = devm_platform_ioremap_resource_byname(pdev, "dram"); + if (IS_ERR(priv->reg_dram)) + return PTR_ERR(priv->reg_dram); + + priv->reg_mbus = devm_platform_ioremap_resource_byname(pdev, "mbus"); + if (IS_ERR(priv->reg_mbus)) + return PTR_ERR(priv->reg_mbus); + + priv->clk_bus = devm_clk_get(dev, "bus"); + if (IS_ERR(priv->clk_bus)) + return dev_err_probe(dev, PTR_ERR(priv->clk_bus), + "failed to get bus clock\n"); + + priv->clk_dram = devm_clk_get(dev, "dram"); + if (IS_ERR(priv->clk_dram)) + return dev_err_probe(dev, PTR_ERR(priv->clk_dram), + "failed to get dram clock\n"); + + priv->clk_mbus = devm_clk_get(dev, "mbus"); + if (IS_ERR(priv->clk_mbus)) + return dev_err_probe(dev, PTR_ERR(priv->clk_mbus), + "failed to get mbus clock\n"); + + ret = clk_prepare_enable(priv->clk_bus); + if (ret) + return dev_err_probe(dev, ret, + "failed to enable bus clock\n"); + + /* Lock the DRAM clock rate to keep priv->nominal_bw in sync. */ + ret = clk_rate_exclusive_get(priv->clk_dram); + if (ret) { + err = "failed to lock dram clock rate\n"; + goto err_disable_bus; + } + + /* Lock the MBUS clock rate to keep MBUS_TMR_PERIOD in sync. */ + ret = clk_rate_exclusive_get(priv->clk_mbus); + if (ret) { + err = "failed to lock mbus clock rate\n"; + goto err_unlock_dram; + } + + priv->gov_data.upthreshold = 10; + priv->gov_data.downdifferential = 5; + + priv->profile.initial_freq = clk_get_rate(priv->clk_dram); + priv->profile.polling_ms = 1000; + priv->profile.target = sun8i_a33_mbus_set_dram_target; + priv->profile.get_dev_status = sun8i_a33_mbus_get_dram_status; + priv->profile.freq_table = priv->freq_table; + priv->profile.max_state = max_state; + + ret = devm_pm_opp_set_clkname(dev, "dram"); + if (ret) { + err = "failed to add OPP table\n"; + goto err_unlock_mbus; + } + + base_freq = clk_get_rate(clk_get_parent(priv->clk_dram)); + for (i = 0; i < max_state; ++i) { + unsigned int div = variant->max_dram_divider - i; + + priv->freq_table[i] = base_freq / div; + + ret = dev_pm_opp_add(dev, priv->freq_table[i], 0); + if (ret) { + err = "failed to add OPPs\n"; + goto err_remove_opps; + } + } + + ret = sun8i_a33_mbus_hw_init(dev, priv, priv->profile.initial_freq); + if (ret) { + err = "failed to init hardware\n"; + goto err_remove_opps; + } + + priv->devfreq_dram = devfreq_add_device(dev, &priv->profile, + DEVFREQ_GOV_SIMPLE_ONDEMAND, + &priv->gov_data); + if (IS_ERR(priv->devfreq_dram)) { + ret = PTR_ERR(priv->devfreq_dram); + err = "failed to add devfreq device\n"; + goto err_remove_opps; + } + + /* + * This must be set manually after registering the devfreq device, + * because there is no way to select a dynamic OPP as the suspend OPP. + */ + priv->devfreq_dram->suspend_freq = priv->freq_table[0]; + + return 0; + +err_remove_opps: + dev_pm_opp_remove_all_dynamic(dev); +err_unlock_mbus: + clk_rate_exclusive_put(priv->clk_mbus); +err_unlock_dram: + clk_rate_exclusive_put(priv->clk_dram); +err_disable_bus: + clk_disable_unprepare(priv->clk_bus); + + return dev_err_probe(dev, ret, err); +} + +static int sun8i_a33_mbus_remove(struct platform_device *pdev) +{ + struct sun8i_a33_mbus *priv = platform_get_drvdata(pdev); + unsigned long initial_freq = priv->profile.initial_freq; + struct device *dev = &pdev->dev; + int ret; + + devfreq_remove_device(priv->devfreq_dram); + + ret = sun8i_a33_mbus_set_dram_freq(priv, initial_freq); + if (ret) + dev_warn(dev, "failed to restore DRAM frequency: %d\n", ret); + + dev_pm_opp_remove_all_dynamic(dev); + clk_rate_exclusive_put(priv->clk_mbus); + clk_rate_exclusive_put(priv->clk_dram); + clk_disable_unprepare(priv->clk_bus); + + return 0; +} + +static const struct sun8i_a33_mbus_variant sun50i_a64_mbus = { + .min_dram_divider = 1, + .max_dram_divider = 4, + .odt_freq_mhz = 400, +}; + +static const struct of_device_id sun8i_a33_mbus_of_match[] = { + { .compatible = "allwinner,sun50i-a64-mbus", .data = &sun50i_a64_mbus }, + { .compatible = "allwinner,sun50i-h5-mbus", .data = &sun50i_a64_mbus }, + { }, +}; +MODULE_DEVICE_TABLE(of, sun8i_a33_mbus_of_match); + +static SIMPLE_DEV_PM_OPS(sun8i_a33_mbus_pm_ops, + sun8i_a33_mbus_suspend, sun8i_a33_mbus_resume); + +static struct platform_driver sun8i_a33_mbus_driver = { + .probe = sun8i_a33_mbus_probe, + .remove = sun8i_a33_mbus_remove, + .driver = { + .name = "sun8i-a33-mbus", + .of_match_table = sun8i_a33_mbus_of_match, + .pm = pm_ptr(&sun8i_a33_mbus_pm_ops), + }, +}; +module_platform_driver(sun8i_a33_mbus_driver); + +MODULE_AUTHOR("Samuel Holland "); +MODULE_DESCRIPTION("Allwinner sun8i/sun50i MBUS DEVFREQ Driver"); +MODULE_LICENSE("GPL v2"); From a4b3c62fd0e8673cb6708ad65551020c8e25d3f2 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 15 Dec 2021 15:03:09 +0100 Subject: [PATCH 2/8] PM / devfreq: sun8i: addd COMMON_CLK dependency Compile-testing the driver without CONFIG_COMMON_CLK causes a link failure: arm-linux-gnueabi-ld: drivers/devfreq/sun8i-a33-mbus.o: in function `sun8i_a33_mbus_remove': sun8i-a33-mbus.c:(.text+0x450): undefined reference to `clk_rate_exclusive_put' arm-linux-gnueabi-ld: sun8i-a33-mbus.c:(.text+0x460): undefined reference to `clk_rate_exclusive_put' arm-linux-gnueabi-ld: drivers/devfreq/sun8i-a33-mbus.o: in function `sun8i_a33_mbus_probe': sun8i-a33-mbus.c:(.text+0x85c): undefined reference to `clk_rate_exclusive_get' arm-linux-gnueabi-ld: sun8i-a33-mbus.c:(.text+0x878): undefined reference to `clk_rate_exclusive_get' Fixes: 8bfd4858b4bb ("PM / devfreq: Add a driver for the sun8i/sun50i MBUS") Signed-off-by: Arnd Bergmann Signed-off-by: Chanwoo Choi --- drivers/devfreq/Kconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig index b94eb04761f6..87eb2b837e68 100644 --- a/drivers/devfreq/Kconfig +++ b/drivers/devfreq/Kconfig @@ -135,6 +135,7 @@ config ARM_RK3399_DMC_DEVFREQ config ARM_SUN8I_A33_MBUS_DEVFREQ tristate "sun8i/sun50i MBUS DEVFREQ Driver" depends on ARCH_SUNXI || COMPILE_TEST + depends on COMMON_CLK select DEVFREQ_GOV_SIMPLE_ONDEMAND help This adds the DEVFREQ driver for the MBUS controller in some From 4667431419e93b63b4edfe7abdfc96cefcbcc051 Mon Sep 17 00:00:00 2001 From: Tzung-Bi Shih Date: Tue, 14 Dec 2021 14:31:00 +0800 Subject: [PATCH 3/8] PM / devfreq: Reduce log severity for informative message Suppose devfreq_update_status() failure in devfreq_set_target() is not a critical error, reduces the log severity. Signed-off-by: Tzung-Bi Shih Signed-off-by: Chanwoo Choi --- drivers/devfreq/devfreq.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/devfreq/devfreq.c b/drivers/devfreq/devfreq.c index 7906220d025c..a525a609dfc6 100644 --- a/drivers/devfreq/devfreq.c +++ b/drivers/devfreq/devfreq.c @@ -382,8 +382,8 @@ static int devfreq_set_target(struct devfreq *devfreq, unsigned long new_freq, devfreq_notify_transition(devfreq, &freqs, DEVFREQ_POSTCHANGE); if (devfreq_update_status(devfreq, new_freq)) - dev_err(&devfreq->dev, - "Couldn't update frequency transition information.\n"); + dev_warn(&devfreq->dev, + "Couldn't update frequency transition information.\n"); devfreq->previous_freq = new_freq; From 931da6a0de5d620425af4425344259e6ff46b654 Mon Sep 17 00:00:00 2001 From: Zhang Rui Date: Tue, 7 Dec 2021 21:17:34 +0800 Subject: [PATCH 4/8] powercap: intel_rapl: support new layout of Psys PowerLimit Register on SPR On Sapphire Rapids, the layout of the Psys domain Power Limit Register is different from from what it was before. Enhance the code to support the new Psys PL register layout. Signed-off-by: Zhang Rui Reported-and-tested-by: Alkattan Dana [ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki --- drivers/powercap/intel_rapl_common.c | 61 +++++++++++++++++++++++++++- include/linux/intel_rapl.h | 6 +++ 2 files changed, 65 insertions(+), 2 deletions(-) diff --git a/drivers/powercap/intel_rapl_common.c b/drivers/powercap/intel_rapl_common.c index 7c0099e7a6d7..07611a00b78f 100644 --- a/drivers/powercap/intel_rapl_common.c +++ b/drivers/powercap/intel_rapl_common.c @@ -61,6 +61,20 @@ #define PERF_STATUS_THROTTLE_TIME_MASK 0xffffffff #define PP_POLICY_MASK 0x1F +/* + * SPR has different layout for Psys Domain PowerLimit registers. + * There are 17 bits of PL1 and PL2 instead of 15 bits. + * The Enable bits and TimeWindow bits are also shifted as a result. + */ +#define PSYS_POWER_LIMIT1_MASK 0x1FFFF +#define PSYS_POWER_LIMIT1_ENABLE BIT(17) + +#define PSYS_POWER_LIMIT2_MASK (0x1FFFFULL<<32) +#define PSYS_POWER_LIMIT2_ENABLE BIT_ULL(49) + +#define PSYS_TIME_WINDOW1_MASK (0x7FULL<<19) +#define PSYS_TIME_WINDOW2_MASK (0x7FULL<<51) + /* Non HW constants */ #define RAPL_PRIMITIVE_DERIVED BIT(1) /* not from raw data */ #define RAPL_PRIMITIVE_DUMMY BIT(2) @@ -97,6 +111,7 @@ struct rapl_defaults { bool to_raw); unsigned int dram_domain_energy_unit; unsigned int psys_domain_energy_unit; + bool spr_psys_bits; }; static struct rapl_defaults *rapl_defaults; @@ -669,12 +684,51 @@ static struct rapl_primitive_info rpi[] = { RAPL_DOMAIN_REG_PERF, TIME_UNIT, 0), PRIMITIVE_INFO_INIT(PRIORITY_LEVEL, PP_POLICY_MASK, 0, RAPL_DOMAIN_REG_POLICY, ARBITRARY_UNIT, 0), + PRIMITIVE_INFO_INIT(PSYS_POWER_LIMIT1, PSYS_POWER_LIMIT1_MASK, 0, + RAPL_DOMAIN_REG_LIMIT, POWER_UNIT, 0), + PRIMITIVE_INFO_INIT(PSYS_POWER_LIMIT2, PSYS_POWER_LIMIT2_MASK, 32, + RAPL_DOMAIN_REG_LIMIT, POWER_UNIT, 0), + PRIMITIVE_INFO_INIT(PSYS_PL1_ENABLE, PSYS_POWER_LIMIT1_ENABLE, 17, + RAPL_DOMAIN_REG_LIMIT, ARBITRARY_UNIT, 0), + PRIMITIVE_INFO_INIT(PSYS_PL2_ENABLE, PSYS_POWER_LIMIT2_ENABLE, 49, + RAPL_DOMAIN_REG_LIMIT, ARBITRARY_UNIT, 0), + PRIMITIVE_INFO_INIT(PSYS_TIME_WINDOW1, PSYS_TIME_WINDOW1_MASK, 19, + RAPL_DOMAIN_REG_LIMIT, TIME_UNIT, 0), + PRIMITIVE_INFO_INIT(PSYS_TIME_WINDOW2, PSYS_TIME_WINDOW2_MASK, 51, + RAPL_DOMAIN_REG_LIMIT, TIME_UNIT, 0), /* non-hardware */ PRIMITIVE_INFO_INIT(AVERAGE_POWER, 0, 0, 0, POWER_UNIT, RAPL_PRIMITIVE_DERIVED), {NULL, 0, 0, 0}, }; +static enum rapl_primitives +prim_fixups(struct rapl_domain *rd, enum rapl_primitives prim) +{ + if (!rapl_defaults->spr_psys_bits) + return prim; + + if (rd->id != RAPL_DOMAIN_PLATFORM) + return prim; + + switch (prim) { + case POWER_LIMIT1: + return PSYS_POWER_LIMIT1; + case POWER_LIMIT2: + return PSYS_POWER_LIMIT2; + case PL1_ENABLE: + return PSYS_PL1_ENABLE; + case PL2_ENABLE: + return PSYS_PL2_ENABLE; + case TIME_WINDOW1: + return PSYS_TIME_WINDOW1; + case TIME_WINDOW2: + return PSYS_TIME_WINDOW2; + default: + return prim; + } +} + /* Read primitive data based on its related struct rapl_primitive_info. * if xlate flag is set, return translated data based on data units, i.e. * time, energy, and power. @@ -692,7 +746,8 @@ static int rapl_read_data_raw(struct rapl_domain *rd, enum rapl_primitives prim, bool xlate, u64 *data) { u64 value; - struct rapl_primitive_info *rp = &rpi[prim]; + enum rapl_primitives prim_fixed = prim_fixups(rd, prim); + struct rapl_primitive_info *rp = &rpi[prim_fixed]; struct reg_action ra; int cpu; @@ -738,7 +793,8 @@ static int rapl_write_data_raw(struct rapl_domain *rd, enum rapl_primitives prim, unsigned long long value) { - struct rapl_primitive_info *rp = &rpi[prim]; + enum rapl_primitives prim_fixed = prim_fixups(rd, prim); + struct rapl_primitive_info *rp = &rpi[prim_fixed]; int cpu; u64 bits; struct reg_action ra; @@ -981,6 +1037,7 @@ static const struct rapl_defaults rapl_defaults_spr_server = { .compute_time_window = rapl_compute_time_window_core, .dram_domain_energy_unit = 15300, .psys_domain_energy_unit = 1000000000, + .spr_psys_bits = true, }; static const struct rapl_defaults rapl_defaults_byt = { diff --git a/include/linux/intel_rapl.h b/include/linux/intel_rapl.h index 93780834fc8f..9f4b6f5b822f 100644 --- a/include/linux/intel_rapl.h +++ b/include/linux/intel_rapl.h @@ -58,6 +58,12 @@ enum rapl_primitives { THROTTLED_TIME, PRIORITY_LEVEL, + PSYS_POWER_LIMIT1, + PSYS_POWER_LIMIT2, + PSYS_PL1_ENABLE, + PSYS_PL2_ENABLE, + PSYS_TIME_WINDOW1, + PSYS_TIME_WINDOW2, /* below are not raw primitive data */ AVERAGE_POWER, NR_RAPL_PRIMITIVES, From 86ffed3de3acbc6e292870ea04dfa1102521a051 Mon Sep 17 00:00:00 2001 From: Jason Wang Date: Sun, 12 Dec 2021 11:06:40 +0800 Subject: [PATCH 5/8] powercap: fix typo in a comment in idle_inject.c Drop superfluous "the" from the comment in line 15. Signed-off-by: Jason Wang [ rjw: Subject edit, new changelog ] Signed-off-by: Rafael J. Wysocki --- drivers/powercap/idle_inject.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/powercap/idle_inject.c b/drivers/powercap/idle_inject.c index 6e1a0043c411..a20bf12f3ce3 100644 --- a/drivers/powercap/idle_inject.c +++ b/drivers/powercap/idle_inject.c @@ -12,7 +12,7 @@ * * All of the kthreads used for idle injection are created at init time. * - * Next, the users of the the idle injection framework provide a cpumask via + * Next, the users of the idle injection framework provide a cpumask via * its register function. The kthreads will be synchronized with respect to * this cpumask. * From 66b354064a35b6379963cba27b5d37a278fc9bd9 Mon Sep 17 00:00:00 2001 From: Daniel Lezcano Date: Tue, 23 Nov 2021 11:16:00 +0100 Subject: [PATCH 6/8] powercap/drivers/dtpm: Remove unused function definition The dtpm.h header file is exporting a function which is not implemented neither needed. Remove it. Signed-off-by: Daniel Lezcano Link: https://lore.kernel.org/r/20211123101601.2433340-1-daniel.lezcano@linaro.org --- include/linux/dtpm.h | 2 -- 1 file changed, 2 deletions(-) diff --git a/include/linux/dtpm.h b/include/linux/dtpm.h index 2890f6370eb9..d37e5d06a357 100644 --- a/include/linux/dtpm.h +++ b/include/linux/dtpm.h @@ -70,6 +70,4 @@ void dtpm_unregister(struct dtpm *dtpm); int dtpm_register(const char *name, struct dtpm *dtpm, struct dtpm *parent); -int dtpm_register_cpu(struct dtpm *parent); - #endif From c1af85e442278fe120974358cf71c41bc48e0580 Mon Sep 17 00:00:00 2001 From: Daniel Lezcano Date: Tue, 23 Nov 2021 11:16:01 +0100 Subject: [PATCH 7/8] powercap/drivers/dtpm: Reduce trace verbosity The traces when registering a powerzone is at the pr_info level and should be changed to pr_debug as requested by Greg-KH. Cc: Greg KH Reviewed-by: Greg Kroah-Hartman Link: https://lkml.kernel.org/r/YGAnRx8SiZHFPpY6@kroah.com Signed-off-by: Daniel Lezcano Link: https://lore.kernel.org/r/20211123101601.2433340-2-daniel.lezcano@linaro.org --- drivers/powercap/dtpm.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/powercap/dtpm.c b/drivers/powercap/dtpm.c index 2a5c1829aab7..8cb45f2d3d78 100644 --- a/drivers/powercap/dtpm.c +++ b/drivers/powercap/dtpm.c @@ -382,7 +382,7 @@ void dtpm_unregister(struct dtpm *dtpm) { powercap_unregister_zone(pct, &dtpm->zone); - pr_info("Unregistered dtpm node '%s'\n", dtpm->zone.name); + pr_debug("Unregistered dtpm node '%s'\n", dtpm->zone.name); } /** @@ -453,8 +453,8 @@ int dtpm_register(const char *name, struct dtpm *dtpm, struct dtpm *parent) dtpm->power_limit = dtpm->power_max; } - pr_info("Registered dtpm node '%s' / %llu-%llu uW, \n", - dtpm->zone.name, dtpm->power_min, dtpm->power_max); + pr_debug("Registered dtpm node '%s' / %llu-%llu uW, \n", + dtpm->zone.name, dtpm->power_min, dtpm->power_max); mutex_unlock(&dtpm_lock); From 489a00ef46c93e85ed540d91836317cc469371ac Mon Sep 17 00:00:00 2001 From: Tang Yizhou Date: Sun, 26 Dec 2021 16:18:39 +0800 Subject: [PATCH 8/8] Documentation: power: Update outdated contents in opp.rst Three problems have been revised: 1. CONFIG_PM_OPP no longer depends on CONFIG_PM. 2. opp_find_freq_{ceil, floor} is renamed as dev_pm_opp_find_freq_{ceil, floor}. 3. Make it clear that the 'opp' struct is actually dev_pm_opp. Signed-off-by: Tang Yizhou Signed-off-by: Viresh Kumar --- Documentation/power/opp.rst | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/Documentation/power/opp.rst b/Documentation/power/opp.rst index e3cc4f349ea8..a7c03c470980 100644 --- a/Documentation/power/opp.rst +++ b/Documentation/power/opp.rst @@ -48,9 +48,9 @@ We can represent these as three OPPs as the following {Hz, uV} tuples: OPP library provides a set of helper functions to organize and query the OPP information. The library is located in drivers/opp/ directory and the header is located in include/linux/pm_opp.h. OPP library can be enabled by enabling -CONFIG_PM_OPP from power management menuconfig menu. OPP library depends on -CONFIG_PM as certain SoCs such as Texas Instrument's OMAP framework allows to -optionally boot at a certain OPP without needing cpufreq. +CONFIG_PM_OPP from power management menuconfig menu. Certain SoCs such as Texas +Instrument's OMAP framework allows to optionally boot at a certain OPP without +needing cpufreq. Typical usage of the OPP library is as follows:: @@ -75,8 +75,8 @@ operations until that OPP could be re-enabled if possible. OPP library facilitates this concept in its implementation. The following operational functions operate only on available opps: -opp_find_freq_{ceil, floor}, dev_pm_opp_get_voltage, dev_pm_opp_get_freq, -dev_pm_opp_get_opp_count +dev_pm_opp_find_freq_{ceil, floor}, dev_pm_opp_get_voltage, dev_pm_opp_get_freq, +dev_pm_opp_get_opp_count. dev_pm_opp_find_freq_exact is meant to be used to find the opp pointer which can then be used for dev_pm_opp_enable/disable functions to make an @@ -103,7 +103,7 @@ dev_pm_opp_add The OPP is defined using the frequency and voltage. Once added, the OPP is assumed to be available and control of its availability can be done with the dev_pm_opp_enable/disable functions. OPP library - internally stores and manages this information in the opp struct. + internally stores and manages this information in the dev_pm_opp struct. This function may be used by SoC framework to define a optimal list as per the demands of SoC usage environment. @@ -247,7 +247,7 @@ dev_pm_opp_disable 5. OPP Data Retrieval Functions =============================== Since OPP library abstracts away the OPP information, a set of functions to pull -information from the OPP structure is necessary. Once an OPP pointer is +information from the dev_pm_opp structure is necessary. Once an OPP pointer is retrieved using the search functions, the following functions can be used by SoC framework to retrieve the information represented inside the OPP layer.