diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt
new file mode 100644
index 000000000000..93986a5a8018
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt
@@ -0,0 +1,30 @@
+* Compact Flash
+
+The Cavium Compact Flash device is connected to the Octeon Boot Bus,
+and is thus a child of the Boot Bus device.  It can read and write
+industry standard compact flash devices.
+
+Properties:
+- compatible: "cavium,ebt3000-compact-flash";
+
+  Compatibility with many Cavium evaluation boards.
+
+- reg: The base address of the the CF chip select banks.  Depending on
+  the device configuration, there may be one or two banks.
+
+- cavium,bus-width: The width of the connection to the CF devices.  Valid
+  values are 8 and 16.
+
+- cavium,true-ide: Optional, if present the CF connection is in True IDE mode.
+
+- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected
+  to this device.
+
+Example:
+	compact-flash@5,0 {
+		compatible = "cavium,ebt3000-compact-flash";
+		reg = <5 0 0x10000>, <6 0 0x10000>;
+		cavium,bus-width = <16>;
+		cavium,true-ide;
+		cavium,dma-engine-handle = <&dma0>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
new file mode 100644
index 000000000000..9d6dcd3fe7f9
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
@@ -0,0 +1,49 @@
+* General Purpose Input Output (GPIO) bus.
+
+Properties:
+- compatible: "cavium,octeon-3860-gpio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the GPIO unit's register bank.
+
+- gpio-controller: This is a GPIO controller.
+
+- #gpio-cells: Must be <2>.  The first cell is the GPIO pin.
+
+- interrupt-controller: The GPIO controller is also an interrupt
+  controller, many of its pins may be configured as an interrupt
+  source.
+
+- #interrupt-cells: Must be <2>.  The first cell is the GPIO pin
+   connected to the interrupt source.  The second cell is the interrupt
+   triggering protocol and may have one of four values:
+   1 - edge triggered on the rising edge.
+   2 - edge triggered on the falling edge
+   4 - level triggered active high.
+   8 - level triggered active low.
+
+- interrupts: Interrupt routing for each pin.
+
+Example:
+
+	gpio-controller@1070000000800 {
+		#gpio-cells = <2>;
+		compatible = "cavium,octeon-3860-gpio";
+		reg = <0x10700 0x00000800 0x0 0x100>;
+		gpio-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) GPIO pin number (0..15)
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		/* The GPIO pin connect to 16 consecutive CUI bits */
+		interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+			     <0 20>, <0 21>, <0 22>, <0 23>,
+			     <0 24>, <0 25>, <0 26>, <0 27>,
+			     <0 28>, <0 29>, <0 30>, <0 31>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt
new file mode 100644
index 000000000000..dced82ebe31d
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt
@@ -0,0 +1,34 @@
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+	twsi0: i2c@1180000001000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cavium,octeon-3860-twsi";
+		reg = <0x11800 0x00001000 0x0 0x200>;
+		interrupts = <0 45>;
+		clock-frequency = <100000>;
+
+		rtc@68 {
+			compatible = "dallas,ds1337";
+			reg = <0x68>;
+		};
+		tmp@4c {
+			compatible = "ti,tmp421";
+			reg = <0x4c>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
new file mode 100644
index 000000000000..6581478225a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
@@ -0,0 +1,126 @@
+* Boot Bus
+
+The Octeon Boot Bus is a configurable parallel bus with 8 chip
+selects.  Each chip select is independently configurable.
+
+Properties:
+- compatible: "cavium,octeon-3860-bootbus"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the Boot Bus' register bank.
+
+- #address-cells: Must be <2>.  The first cell is the chip select
+   within the bootbus.  The second cell is the offset from the chip select.
+
+- #size-cells: Must be <1>.
+
+- ranges: There must be one one triplet of (child-bus-address,
+  parent-bus-address, length) for each active chip select.  If the
+  length element for any triplet is zero, the chip select is disabled,
+  making it inactive.
+
+The configuration parameters for each chip select are stored in child
+nodes.
+
+Configuration Properties:
+- compatible:  "cavium,octeon-3860-bootbus-config"
+
+- cavium,cs-index: A single cell indicating the chip select that
+  corresponds to this configuration.
+
+- cavium,t-adr: A cell specifying the ADR timing (in nS).
+
+- cavium,t-ce: A cell specifying the CE timing (in nS).
+
+- cavium,t-oe: A cell specifying the OE timing (in nS).
+
+- cavium,t-we: A cell specifying the WE timing (in nS).
+
+- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS).
+
+- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS).
+
+- cavium,t-pause: A cell specifying the PAUSE timing (in nS).
+
+- cavium,t-wait: A cell specifying the WAIT timing (in nS).
+
+- cavium,t-page: A cell specifying the PAGE timing (in nS).
+
+- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS).
+
+- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1
+  = 2 bytes, 2 = 4 bytes, 3 = 8 bytes).
+
+- cavium,wait-mode: Optional.  If present, wait mode (WAITM) is selected.
+
+- cavium,page-mode: Optional.  If present, page mode (PAGEM) is selected.
+
+- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of
+  the bus for this chip select.
+
+- cavium,ale-mode: Optional.  If present, ALE mode is selected.
+
+- cavium,sam-mode: Optional.  If present, SAM mode is selected.
+
+- cavium,or-mode: Optional.  If present, OR mode is selected.
+
+Example:
+	bootbus: bootbus@1180000000000 {
+		compatible = "cavium,octeon-3860-bootbus";
+		reg = <0x11800 0x00000000 0x0 0x200>;
+		/* The chip select number and offset */
+		#address-cells = <2>;
+		/* The size of the chip select region */
+		#size-cells = <1>;
+		ranges = <0 0  0x0 0x1f400000  0xc00000>,
+			 <1 0  0x10000 0x30000000  0>,
+			 <2 0  0x10000 0x40000000  0>,
+			 <3 0  0x10000 0x50000000  0>,
+			 <4 0  0x0 0x1d020000  0x10000>,
+			 <5 0  0x0 0x1d040000  0x10000>,
+			 <6 0  0x0 0x1d050000  0x10000>,
+			 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <0>;
+			cavium,t-adr  = <20>;
+			cavium,t-ce   = <60>;
+			cavium,t-oe   = <60>;
+			cavium,t-we   = <45>;
+			cavium,t-rd-hld = <35>;
+			cavium,t-wr-hld = <45>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <35>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,bus-width = <8>;
+		};
+		.
+		.
+		.
+		cavium,cs-config@6 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <6>;
+			cavium,t-adr  = <5>;
+			cavium,t-ce   = <300>;
+			cavium,t-oe   = <270>;
+			cavium,t-we   = <150>;
+			cavium,t-rd-hld = <100>;
+			cavium,t-wr-hld = <70>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <320>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,wait-mode;
+			cavium,bus-width = <16>;
+		};
+		.
+		.
+		.
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
new file mode 100644
index 000000000000..2c2d0746b43d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
@@ -0,0 +1,26 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-3860-ciu"
+
+  Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+   the CIU and may have a value of 0 or 1.  The second cell is the bit
+   within the bank and may have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070000000000 {
+		compatible = "cavium,octeon-3860-ciu";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0 or 1)
+		 * 2) Bit within the register (0..63)
+		 */
+		#interrupt-cells = <2>;
+		reg = <0x10700 0x00000000 0x0 0x7000>;
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu2.txt b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt
new file mode 100644
index 000000000000..0ec7ba8bbbcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt
@@ -0,0 +1,27 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-6880-ciu2"
+
+  Compatibility with 68XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+  the CIU and may have a value between 0 and 63.  The second cell is
+  the bit within the bank and may also have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070100000000 {
+		compatible = "cavium,octeon-6880-ciu2";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0..63)
+		 * 2) Bit within the register (0..63)
+		 */
+		#address-cells = <0>;
+		#interrupt-cells = <2>;
+		reg = <0x10701 0x00000000 0x0 0x4000000>;
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
new file mode 100644
index 000000000000..cb4291e3b1d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
@@ -0,0 +1,21 @@
+* DMA Engine.
+
+The Octeon DMA Engine transfers between the Boot Bus and main memory.
+The DMA Engine will be refered to by phandle by any device that is
+connected to it.
+
+Properties:
+- compatible: "cavium,octeon-5750-bootbus-dma"
+
+  Compatibility with all cn52XX, cn56XX and cn6XXX SOCs.
+
+- reg: The base address of the DMA Engine's register bank.
+
+- interrupts: A single interrupt specifier.
+
+Example:
+	dma0: dma-engine@1180000000100 {
+		compatible = "cavium,octeon-5750-bootbus-dma";
+		reg = <0x11800 0x00000100 0x0 0x8>;
+		interrupts = <0 63>;
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
new file mode 100644
index 000000000000..aa66b9b8d801
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
@@ -0,0 +1,46 @@
+* UCTL USB controller glue
+
+Properties:
+- compatible: "cavium,octeon-6335-uctl"
+
+  Compatibility with all cn6XXX SOCs.
+
+- reg: The base address of the UCTL register bank.
+
+- #address-cells: Must be <2>.
+
+- #size-cells: Must be <2>.
+
+- ranges: Empty to signify direct mapping of the children.
+
+- refclk-frequency: A single cell containing the reference clock
+  frequency in Hz.
+
+- refclk-type: A string describing the reference clock connection
+  either "crystal" or "external".
+
+Example:
+	uctl@118006f000000 {
+		compatible = "cavium,octeon-6335-uctl";
+		reg = <0x11800 0x6f000000 0x0 0x100>;
+		ranges; /* Direct mapping */
+		#address-cells = <2>;
+		#size-cells = <2>;
+		/* 12MHz, 24MHz and 48MHz allowed */
+		refclk-frequency = <24000000>;
+		/* Either "crystal" or "external" */
+		refclk-type = "crystal";
+
+		ehci@16f0000000000 {
+			compatible = "cavium,octeon-6335-ehci","usb-ehci";
+			reg = <0x16f00 0x00000000 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+		ohci@16f0000000400 {
+			compatible = "cavium,octeon-6335-ohci","usb-ohci";
+			reg = <0x16f00 0x00000400 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt
new file mode 100644
index 000000000000..04cb7491d232
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt
@@ -0,0 +1,27 @@
+* System Management Interface (SMI) / MDIO
+
+Properties:
+- compatible: "cavium,octeon-3860-mdio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the MDIO bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  MDIO addresses have no size component.
+
+Typically an MDIO bus might have several children.
+
+Example:
+	mdio@1180000001800 {
+		compatible = "cavium,octeon-3860-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11800 0x00001800 0x0 0x40>;
+
+		ethernet-phy@0 {
+			...
+			reg = <0>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt
new file mode 100644
index 000000000000..5da628db68bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mix.txt
@@ -0,0 +1,39 @@
+* MIX Ethernet controller.
+
+Properties:
+- compatible: "cavium,octeon-5750-mix"
+
+  Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
+  devices.
+
+- reg: The base addresses of four separate register banks.  The first
+  bank contains the MIX registers.  The second bank the corresponding
+  AGL registers.  The third bank are the AGL registers shared by all
+  MIX devices present.  The fourth bank is the AGL_PRT_CTL shared by
+  all MIX devices present.
+
+- cell-index: A single cell specifying which portion of the shared
+  register banks corresponds to this MIX device.
+
+- interrupts: Two interrupt specifiers.  The first is the MIX
+  interrupt routing and the second the routing for the AGL interrupts.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+  if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+	ethernet@1070000100800 {
+		compatible = "cavium,octeon-5750-mix";
+		reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+		      <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+		      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+		      <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
+		cell-index = <1>;
+		interrupts = <1 18>, < 1 46>;
+		local-mac-address = [ 00 0f b7 10 63 54 ];
+		phy-handle = <&phy1>;
+	};
diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt
new file mode 100644
index 000000000000..d4c53ba04b3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-pip.txt
@@ -0,0 +1,98 @@
+* PIP Ethernet nexus.
+
+The PIP Ethernet nexus can control several data packet input/output
+devices.  The devices have a two level grouping scheme.  There may be
+several interfaces, and each interface may have several ports.  These
+ports might be an individual Ethernet PHY.
+
+
+Properties for the PIP nexus:
+- compatible: "cavium,octeon-3860-pip"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the PIP's register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP interfaces which is a child the PIP nexus:
+- compatible: "cavium,octeon-3860-pip-interface"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The interface number.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP port which is a child the PIP interface:
+- compatible: "cavium,octeon-3860-pip-port"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The port number within the interface group.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+  if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+
+	pip@11800a0000000 {
+		compatible = "cavium,octeon-3860-pip";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+		interface@0 {
+			compatible = "cavium,octeon-3860-pip-interface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>; /* interface */
+
+			ethernet@0 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x0>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 60 ];
+				phy-handle = <&phy2>;
+			};
+			ethernet@1 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x1>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 61 ];
+				phy-handle = <&phy3>;
+			};
+			ethernet@2 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x2>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 62 ];
+				phy-handle = <&phy4>;
+			};
+			ethernet@3 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x3>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 63 ];
+				phy-handle = <&phy5>;
+			};
+		};
+
+		interface@1 {
+			compatible = "cavium,octeon-3860-pip-interface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>; /* interface */
+
+			ethernet@0 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x0>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 64 ];
+				phy-handle = <&phy6>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/serial/cavium-uart.txt b/Documentation/devicetree/bindings/serial/cavium-uart.txt
new file mode 100644
index 000000000000..87a6c375cd44
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/cavium-uart.txt
@@ -0,0 +1,19 @@
+* Universal Asynchronous Receiver/Transmitter (UART)
+
+- compatible: "cavium,octeon-3860-uart"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the UART register bank.
+
+- interrupts: A single interrupt specifier.
+
+- current-speed: Optional, the current bit rate in bits per second.
+
+Example:
+	uart1: serial@1180000000c00 {
+		compatible = "cavium,octeon-3860-uart","ns16550";
+		reg = <0x11800 0x00000c00 0x0 0x400>;
+		current-speed = <115200>;
+		interrupts = <0 35>;
+	};
diff --git a/arch/mips/cavium-octeon/.gitignore b/arch/mips/cavium-octeon/.gitignore
new file mode 100644
index 000000000000..39c968605ff6
--- /dev/null
+++ b/arch/mips/cavium-octeon/.gitignore
@@ -0,0 +1,2 @@
+*.dtb.S
+*.dtb
diff --git a/arch/mips/cavium-octeon/Makefile b/arch/mips/cavium-octeon/Makefile
index 19eb0434269f..1e37522cc21f 100644
--- a/arch/mips/cavium-octeon/Makefile
+++ b/arch/mips/cavium-octeon/Makefile
@@ -15,3 +15,16 @@ obj-y += octeon-memcpy.o
 obj-y += executive/
 
 obj-$(CONFIG_SMP)                     += smp.o
+
+DTS_FILES = octeon_3xxx.dts octeon_68xx.dts
+DTB_FILES = $(patsubst %.dts, %.dtb, $(DTS_FILES))
+
+obj-y += $(patsubst %.dts, %.dtb.o, $(DTS_FILES))
+
+$(obj)/%.dtb: $(src)/%.dts FORCE
+	$(call if_changed_dep,dtc)
+
+# Let's keep the .dtb files around in case we want to look at them.
+.SECONDARY:  $(addprefix $(obj)/, $(DTB_FILES))
+
+clean-files += $(DTB_FILES) $(patsubst %.dtb, %.dtb.S, $(DTB_FILES))
diff --git a/arch/mips/cavium-octeon/octeon_3xxx.dts b/arch/mips/cavium-octeon/octeon_3xxx.dts
new file mode 100644
index 000000000000..f28b2d0fde22
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon_3xxx.dts
@@ -0,0 +1,571 @@
+/dts-v1/;
+/*
+ * OCTEON 3XXX, 5XXX, 63XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use.  Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+	compatible = "cavium,octeon-3860";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu>;
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges; /* Direct mapping */
+
+		ciu: interrupt-controller@1070000000000 {
+			compatible = "cavium,octeon-3860-ciu";
+			interrupt-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) Controller register (0 or 1)
+			 * 2) Bit within the register (0..63)
+			 */
+			#interrupt-cells = <2>;
+			reg = <0x10700 0x00000000 0x0 0x7000>;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x00000800 0x0 0x100>;
+			gpio-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) GPIO pin number (0..15)
+			 * 2) Triggering (1 - edge rising
+			 *		  2 - edge falling
+			 *		  4 - level active high
+			 *		  8 - level active low)
+			 */
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* The GPIO pin connect to 16 consecutive CUI bits */
+			interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+				     <0 20>, <0 21>, <0 22>, <0 23>,
+				     <0 24>, <0 25>, <0 26>, <0 27>,
+				     <0 28>, <0 29>, <0 30>, <0 31>;
+		};
+
+		smi0: mdio@1180000001800 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00001800 0x0 0x40>;
+
+			phy0: ethernet-phy@0 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <0>;
+			};
+
+			phy1: ethernet-phy@1 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <1>;
+			};
+
+			phy2: ethernet-phy@2 {
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy3: ethernet-phy@3 {
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy4: ethernet-phy@4 {
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy5: ethernet-phy@5 {
+				reg = <5>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+
+			phy6: ethernet-phy@6 {
+				reg = <6>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy7: ethernet-phy@7 {
+				reg = <7>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy8: ethernet-phy@8 {
+				reg = <8>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy9: ethernet-phy@9 {
+				reg = <9>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi1: mdio@1180000001900 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00001900 0x0 0x40>;
+
+			phy100: ethernet-phy@1 {
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy101: ethernet-phy@2 {
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy102: ethernet-phy@3 {
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy103: ethernet-phy@4 {
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+		};
+
+		mix0: ethernet@1070000100000 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <0>;
+			interrupts = <0 62>, <1 46>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy0>;
+		};
+
+		mix1: ethernet@1070000100800 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <1>;
+			interrupts = <1 18>, < 1 46>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy1>;
+		};
+
+		pip: pip@11800a0000000 {
+			compatible = "cavium,octeon-3860-pip";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@0 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy2>;
+					cavium,alt-phy-handle = <&phy100>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy3>;
+					cavium,alt-phy-handle = <&phy101>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy4>;
+					cavium,alt-phy-handle = <&phy102>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy5>;
+					cavium,alt-phy-handle = <&phy103>;
+				};
+				ethernet@4 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x4>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@5 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x5>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@6 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x6>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@7 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x7>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@8 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x8>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@9 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x9>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@a {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xa>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@b {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xb>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@c {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xc>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@d {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xd>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@e {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xe>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@f {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xf>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@1 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy6>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy7>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy8>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy9>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001000 0x0 0x200>;
+			interrupts = <0 45>;
+			clock-frequency = <100000>;
+
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+			tmp@4c {
+				compatible = "ti,tmp421";
+				reg = <0x4c>;
+			};
+		};
+
+		twsi1: i2c@1180000001200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001200 0x0 0x200>;
+			interrupts = <0 59>;
+			clock-frequency = <100000>;
+		};
+
+		uart0: serial@1180000000800 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000800 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <0 34>;
+		};
+
+		uart1: serial@1180000000c00 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000c00 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <0 35>;
+		};
+
+		uart2: serial@1180000000400 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000400 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <1 16>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00000000 0x0 0x200>;
+			/* The chip select number and offset */
+			#address-cells = <2>;
+			/* The size of the chip select region */
+			#size-cells = <1>;
+			ranges = <0 0  0x0 0x1f400000  0xc00000>,
+				 <1 0  0x10000 0x30000000  0>,
+				 <2 0  0x10000 0x40000000  0>,
+				 <3 0  0x10000 0x50000000  0>,
+				 <4 0  0x0 0x1d020000  0x10000>,
+				 <5 0  0x0 0x1d040000  0x10000>,
+				 <6 0  0x0 0x1d050000  0x10000>,
+				 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <0>;
+				cavium,t-adr  = <20>;
+				cavium,t-ce   = <60>;
+				cavium,t-oe   = <60>;
+				cavium,t-we   = <45>;
+				cavium,t-rd-hld = <35>;
+				cavium,t-wr-hld = <45>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <0>;
+				cavium,t-page   = <35>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@4 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <4>;
+				cavium,t-adr  = <320>;
+				cavium,t-ce   = <320>;
+				cavium,t-oe   = <320>;
+				cavium,t-we   = <320>;
+				cavium,t-rd-hld = <320>;
+				cavium,t-wr-hld = <320>;
+				cavium,t-pause  = <320>;
+				cavium,t-wait   = <320>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@5 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <5>;
+				cavium,t-adr  = <5>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <30>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <30>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <16>;
+			};
+			cavium,cs-config@6 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <6>;
+				cavium,t-adr  = <5>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <270>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <70>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <0>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,wait-mode;
+				cavium,bus-width = <16>;
+			};
+
+			flash0: nor@0,0 {
+				compatible = "cfi-flash";
+				reg = <0 0 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+
+			led0: led-display@4,0 {
+				compatible = "avago,hdsp-253x";
+				reg = <4 0x20 0x20>, <4 0 0x20>;
+			};
+
+			cf0: compact-flash@5,0 {
+				compatible = "cavium,ebt3000-compact-flash";
+				reg = <5 0 0x10000>, <6 0 0x10000>;
+				cavium,bus-width = <16>;
+				cavium,true-ide;
+				cavium,dma-engine-handle = <&dma0>;
+			};
+		};
+
+		dma0: dma-engine@1180000000100 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000100 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+		dma1: dma-engine@1180000000108 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000108 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		uctl: uctl@118006f000000 {
+			compatible = "cavium,octeon-6335-uctl";
+			reg = <0x11800 0x6f000000 0x0 0x100>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+
+			ehci@16f0000000000 {
+				compatible = "cavium,octeon-6335-ehci","usb-ehci";
+				reg = <0x16f00 0x00000000 0x0 0x100>;
+				interrupts = <0 56>;
+				big-endian-regs;
+			};
+			ohci@16f0000000400 {
+				compatible = "cavium,octeon-6335-ohci","usb-ohci";
+				reg = <0x16f00 0x00000400 0x0 0x100>;
+				interrupts = <0 56>;
+				big-endian-regs;
+			};
+		};
+	};
+
+	aliases {
+		mix0 = &mix0;
+		mix1 = &mix1;
+		pip = &pip;
+		smi0 = &smi0;
+		smi1 = &smi1;
+		twsi0 = &twsi0;
+		twsi1 = &twsi1;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		uart2 = &uart2;
+		flash0 = &flash0;
+		cf0 = &cf0;
+		uctl = &uctl;
+		led0 = &led0;
+	};
+ };
diff --git a/arch/mips/cavium-octeon/octeon_68xx.dts b/arch/mips/cavium-octeon/octeon_68xx.dts
new file mode 100644
index 000000000000..1839468932b6
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon_68xx.dts
@@ -0,0 +1,625 @@
+/dts-v1/;
+/*
+ * OCTEON 68XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use.  Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+	compatible = "cavium,octeon-6880";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu2>;
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges; /* Direct mapping */
+
+		ciu2: interrupt-controller@1070100000000 {
+			compatible = "cavium,octeon-6880-ciu2";
+			interrupt-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) Controller register (0 or 7)
+			 * 2) Bit within the register (0..63)
+			 */
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x10701 0x00000000 0x0 0x4000000>;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x00000800 0x0 0x100>;
+			gpio-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) GPIO pin number (0..15)
+			 * 2) Triggering (1 - edge rising
+			 *		  2 - edge falling
+			 *		  4 - level active high
+			 *		  8 - level active low)
+			 */
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* The GPIO pins connect to 16 consecutive CUI bits */
+			interrupts = <7 0>,  <7 1>,  <7 2>,  <7 3>,
+				     <7 4>,  <7 5>,  <7 6>,  <7 7>,
+				     <7 8>,  <7 9>,  <7 10>, <7 11>,
+				     <7 12>, <7 13>, <7 14>, <7 15>;
+		};
+
+		smi0: mdio@1180000003800 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003800 0x0 0x40>;
+
+			phy0: ethernet-phy@6 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <6>;
+			};
+
+			phy1: ethernet-phy@1 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy2: ethernet-phy@2 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy3: ethernet-phy@3 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy4: ethernet-phy@4 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi1: mdio@1180000003880 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003880 0x0 0x40>;
+
+			phy41: ethernet-phy@1 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy42: ethernet-phy@2 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy43: ethernet-phy@3 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy44: ethernet-phy@4 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi2: mdio@1180000003900 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003900 0x0 0x40>;
+
+			phy21: ethernet-phy@1 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy22: ethernet-phy@2 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy23: ethernet-phy@3 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy24: ethernet-phy@4 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi3: mdio@1180000003980 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003980 0x0 0x40>;
+
+			phy11: ethernet-phy@1 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy12: ethernet-phy@2 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy13: ethernet-phy@3 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy14: ethernet-phy@4 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		mix0: ethernet@1070000100000 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <0>;
+			interrupts = <6 40>, <6 32>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy0>;
+		};
+
+		pip: pip@11800a0000000 {
+			compatible = "cavium,octeon-3860-pip";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@4 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x4>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy1>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy2>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy3>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy4>;
+				};
+			};
+
+			interface@3 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x3>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy11>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy12>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy13>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy14>;
+				};
+			};
+
+			interface@2 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x2>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy21>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy22>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy23>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy24>;
+				};
+			};
+
+			interface@1 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x1>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@0 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy41>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy42>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy43>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy44>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001000 0x0 0x200>;
+			interrupts = <3 32>;
+			clock-frequency = <100000>;
+
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+			tmp@4c {
+				compatible = "ti,tmp421";
+				reg = <0x4c>;
+			};
+		};
+
+		twsi1: i2c@1180000001200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001200 0x0 0x200>;
+			interrupts = <3 33>;
+			clock-frequency = <100000>;
+		};
+
+		uart0: serial@1180000000800 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000800 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <3 36>;
+		};
+
+		uart1: serial@1180000000c00 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000c00 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <3 37>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00000000 0x0 0x200>;
+			/* The chip select number and offset */
+			#address-cells = <2>;
+			/* The size of the chip select region */
+			#size-cells = <1>;
+			ranges = <0 0  0       0x1f400000  0xc00000>,
+				 <1 0  0x10000 0x30000000  0>,
+				 <2 0  0x10000 0x40000000  0>,
+				 <3 0  0x10000 0x50000000  0>,
+				 <4 0  0       0x1d020000  0x10000>,
+				 <5 0  0       0x1d040000  0x10000>,
+				 <6 0  0       0x1d050000  0x10000>,
+				 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <0>;
+				cavium,t-adr  = <10>;
+				cavium,t-ce   = <50>;
+				cavium,t-oe   = <50>;
+				cavium,t-we   = <35>;
+				cavium,t-rd-hld = <25>;
+				cavium,t-wr-hld = <35>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <300>;
+				cavium,t-page   = <25>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@4 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <4>;
+				cavium,t-adr  = <320>;
+				cavium,t-ce   = <320>;
+				cavium,t-oe   = <320>;
+				cavium,t-we   = <320>;
+				cavium,t-rd-hld = <320>;
+				cavium,t-wr-hld = <320>;
+				cavium,t-pause  = <320>;
+				cavium,t-wait   = <320>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@5 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <5>;
+				cavium,t-adr  = <0>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <300>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <300>;
+				cavium,t-page   = <310>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <16>;
+			};
+			cavium,cs-config@6 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <6>;
+				cavium,t-adr  = <0>;
+				cavium,t-ce   = <30>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <30>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <30>;
+				cavium,t-page   = <310>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,wait-mode;
+				cavium,bus-width = <16>;
+			};
+
+			flash0: nor@0,0 {
+				compatible = "cfi-flash";
+				reg = <0 0 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "bootloader";
+					reg = <0 0x200000>;
+					read-only;
+				};
+				partition@200000 {
+					label = "kernel";
+					reg = <0x200000 0x200000>;
+				};
+				partition@400000 {
+					label = "cramfs";
+					reg = <0x400000 0x3fe000>;
+				};
+				partition@7fe000 {
+					label = "environment";
+					reg = <0x7fe000 0x2000>;
+					read-only;
+				};
+			};
+
+			led0: led-display@4,0 {
+				compatible = "avago,hdsp-253x";
+				reg = <4 0x20 0x20>, <4 0 0x20>;
+			};
+
+			compact-flash@5,0 {
+				compatible = "cavium,ebt3000-compact-flash";
+				reg = <5 0 0x10000>, <6 0 0x10000>;
+				cavium,bus-width = <16>;
+				cavium,true-ide;
+				cavium,dma-engine-handle = <&dma0>;
+			};
+		};
+
+		dma0: dma-engine@1180000000100 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000100 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+		dma1: dma-engine@1180000000108 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000108 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		uctl: uctl@118006f000000 {
+			compatible = "cavium,octeon-6335-uctl";
+			reg = <0x11800 0x6f000000 0x0 0x100>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+
+			ehci@16f0000000000 {
+				compatible = "cavium,octeon-6335-ehci","usb-ehci";
+				reg = <0x16f00 0x00000000 0x0 0x100>;
+				interrupts = <3 44>;
+				big-endian-regs;
+			};
+			ohci@16f0000000400 {
+				compatible = "cavium,octeon-6335-ohci","usb-ohci";
+				reg = <0x16f00 0x00000400 0x0 0x100>;
+				interrupts = <3 44>;
+				big-endian-regs;
+			};
+		};
+	};
+
+	aliases {
+		mix0 = &mix0;
+		pip = &pip;
+		smi0 = &smi0;
+		smi1 = &smi1;
+		smi2 = &smi2;
+		smi3 = &smi3;
+		twsi0 = &twsi0;
+		twsi1 = &twsi1;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		uctl = &uctl;
+		led0 = &led0;
+		flash0 = &flash0;
+	};
+ };