diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst index ca0b0dbfd9ad..2227b9f4509d 100644 --- a/Documentation/networking/index.rst +++ b/Documentation/networking/index.rst @@ -113,6 +113,7 @@ Contents: tproxy tuntap udplite + vrf .. only:: subproject and html diff --git a/Documentation/networking/vrf.rst b/Documentation/networking/vrf.rst new file mode 100644 index 000000000000..0dde145043bc --- /dev/null +++ b/Documentation/networking/vrf.rst @@ -0,0 +1,451 @@ +.. SPDX-License-Identifier: GPL-2.0 + +==================================== +Virtual Routing and Forwarding (VRF) +==================================== + +The VRF Device +============== + +The VRF device combined with ip rules provides the ability to create virtual +routing and forwarding domains (aka VRFs, VRF-lite to be specific) in the +Linux network stack. One use case is the multi-tenancy problem where each +tenant has their own unique routing tables and in the very least need +different default gateways. + +Processes can be "VRF aware" by binding a socket to the VRF device. Packets +through the socket then use the routing table associated with the VRF +device. An important feature of the VRF device implementation is that it +impacts only Layer 3 and above so L2 tools (e.g., LLDP) are not affected +(ie., they do not need to be run in each VRF). The design also allows +the use of higher priority ip rules (Policy Based Routing, PBR) to take +precedence over the VRF device rules directing specific traffic as desired. + +In addition, VRF devices allow VRFs to be nested within namespaces. For +example network namespaces provide separation of network interfaces at the +device layer, VLANs on the interfaces within a namespace provide L2 separation +and then VRF devices provide L3 separation. + +Design +------ +A VRF device is created with an associated route table. Network interfaces +are then enslaved to a VRF device:: + + +-----------------------------+ + | vrf-blue | ===> route table 10 + +-----------------------------+ + | | | + +------+ +------+ +-------------+ + | eth1 | | eth2 | ... | bond1 | + +------+ +------+ +-------------+ + | | + +------+ +------+ + | eth8 | | eth9 | + +------+ +------+ + +Packets received on an enslaved device and are switched to the VRF device +in the IPv4 and IPv6 processing stacks giving the impression that packets +flow through the VRF device. Similarly on egress routing rules are used to +send packets to the VRF device driver before getting sent out the actual +interface. This allows tcpdump on a VRF device to capture all packets into +and out of the VRF as a whole\ [1]_. Similarly, netfilter\ [2]_ and tc rules +can be applied using the VRF device to specify rules that apply to the VRF +domain as a whole. + +.. [1] Packets in the forwarded state do not flow through the device, so those + packets are not seen by tcpdump. Will revisit this limitation in a + future release. + +.. [2] Iptables on ingress supports PREROUTING with skb->dev set to the real + ingress device and both INPUT and PREROUTING rules with skb->dev set to + the VRF device. For egress POSTROUTING and OUTPUT rules can be written + using either the VRF device or real egress device. + +Setup +----- +1. VRF device is created with an association to a FIB table. + e.g,:: + + ip link add vrf-blue type vrf table 10 + ip link set dev vrf-blue up + +2. An l3mdev FIB rule directs lookups to the table associated with the device. + A single l3mdev rule is sufficient for all VRFs. The VRF device adds the + l3mdev rule for IPv4 and IPv6 when the first device is created with a + default preference of 1000. Users may delete the rule if desired and add + with a different priority or install per-VRF rules. + + Prior to the v4.8 kernel iif and oif rules are needed for each VRF device:: + + ip ru add oif vrf-blue table 10 + ip ru add iif vrf-blue table 10 + +3. Set the default route for the table (and hence default route for the VRF):: + + ip route add table 10 unreachable default metric 4278198272 + + This high metric value ensures that the default unreachable route can + be overridden by a routing protocol suite. FRRouting interprets + kernel metrics as a combined admin distance (upper byte) and priority + (lower 3 bytes). Thus the above metric translates to [255/8192]. + +4. Enslave L3 interfaces to a VRF device:: + + ip link set dev eth1 master vrf-blue + + Local and connected routes for enslaved devices are automatically moved to + the table associated with VRF device. Any additional routes depending on + the enslaved device are dropped and will need to be reinserted to the VRF + FIB table following the enslavement. + + The IPv6 sysctl option keep_addr_on_down can be enabled to keep IPv6 global + addresses as VRF enslavement changes:: + + sysctl -w net.ipv6.conf.all.keep_addr_on_down=1 + +5. Additional VRF routes are added to associated table:: + + ip route add table 10 ... + + +Applications +------------ +Applications that are to work within a VRF need to bind their socket to the +VRF device:: + + setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1); + +or to specify the output device using cmsg and IP_PKTINFO. + +By default the scope of the port bindings for unbound sockets is +limited to the default VRF. That is, it will not be matched by packets +arriving on interfaces enslaved to an l3mdev and processes may bind to +the same port if they bind to an l3mdev. + +TCP & UDP services running in the default VRF context (ie., not bound +to any VRF device) can work across all VRF domains by enabling the +tcp_l3mdev_accept and udp_l3mdev_accept sysctl options:: + + sysctl -w net.ipv4.tcp_l3mdev_accept=1 + sysctl -w net.ipv4.udp_l3mdev_accept=1 + +These options are disabled by default so that a socket in a VRF is only +selected for packets in that VRF. There is a similar option for RAW +sockets, which is enabled by default for reasons of backwards compatibility. +This is so as to specify the output device with cmsg and IP_PKTINFO, but +using a socket not bound to the corresponding VRF. This allows e.g. older ping +implementations to be run with specifying the device but without executing it +in the VRF. This option can be disabled so that packets received in a VRF +context are only handled by a raw socket bound to the VRF, and packets in the +default VRF are only handled by a socket not bound to any VRF:: + + sysctl -w net.ipv4.raw_l3mdev_accept=0 + +netfilter rules on the VRF device can be used to limit access to services +running in the default VRF context as well. + +-------------------------------------------------------------------------------- + +Using iproute2 for VRFs +======================= +iproute2 supports the vrf keyword as of v4.7. For backwards compatibility this +section lists both commands where appropriate -- with the vrf keyword and the +older form without it. + +1. Create a VRF + + To instantiate a VRF device and associate it with a table:: + + $ ip link add dev NAME type vrf table ID + + As of v4.8 the kernel supports the l3mdev FIB rule where a single rule + covers all VRFs. The l3mdev rule is created for IPv4 and IPv6 on first + device create. + +2. List VRFs + + To list VRFs that have been created:: + + $ ip [-d] link show type vrf + NOTE: The -d option is needed to show the table id + + For example:: + + $ ip -d link show type vrf + 11: mgmt: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 + link/ether 72:b3:ba:91:e2:24 brd ff:ff:ff:ff:ff:ff promiscuity 0 + vrf table 1 addrgenmode eui64 + 12: red: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 + link/ether b6:6f:6e:f6:da:73 brd ff:ff:ff:ff:ff:ff promiscuity 0 + vrf table 10 addrgenmode eui64 + 13: blue: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 + link/ether 36:62:e8:7d:bb:8c brd ff:ff:ff:ff:ff:ff promiscuity 0 + vrf table 66 addrgenmode eui64 + 14: green: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 + link/ether e6:28:b8:63:70:bb brd ff:ff:ff:ff:ff:ff promiscuity 0 + vrf table 81 addrgenmode eui64 + + + Or in brief output:: + + $ ip -br link show type vrf + mgmt UP 72:b3:ba:91:e2:24 + red UP b6:6f:6e:f6:da:73 + blue UP 36:62:e8:7d:bb:8c + green UP e6:28:b8:63:70:bb + + +3. Assign a Network Interface to a VRF + + Network interfaces are assigned to a VRF by enslaving the netdevice to a + VRF device:: + + $ ip link set dev NAME master NAME + + On enslavement connected and local routes are automatically moved to the + table associated with the VRF device. + + For example:: + + $ ip link set dev eth0 master mgmt + + +4. Show Devices Assigned to a VRF + + To show devices that have been assigned to a specific VRF add the master + option to the ip command:: + + $ ip link show vrf NAME + $ ip link show master NAME + + For example:: + + $ ip link show vrf red + 3: eth1: mtu 1500 qdisc pfifo_fast master red state UP mode DEFAULT group default qlen 1000 + link/ether 02:00:00:00:02:02 brd ff:ff:ff:ff:ff:ff + 4: eth2: mtu 1500 qdisc pfifo_fast master red state UP mode DEFAULT group default qlen 1000 + link/ether 02:00:00:00:02:03 brd ff:ff:ff:ff:ff:ff + 7: eth5: mtu 1500 qdisc noop master red state DOWN mode DEFAULT group default qlen 1000 + link/ether 02:00:00:00:02:06 brd ff:ff:ff:ff:ff:ff + + + Or using the brief output:: + + $ ip -br link show vrf red + eth1 UP 02:00:00:00:02:02 + eth2 UP 02:00:00:00:02:03 + eth5 DOWN 02:00:00:00:02:06 + + +5. Show Neighbor Entries for a VRF + + To list neighbor entries associated with devices enslaved to a VRF device + add the master option to the ip command:: + + $ ip [-6] neigh show vrf NAME + $ ip [-6] neigh show master NAME + + For example:: + + $ ip neigh show vrf red + 10.2.1.254 dev eth1 lladdr a6:d9:c7:4f:06:23 REACHABLE + 10.2.2.254 dev eth2 lladdr 5e:54:01:6a:ee:80 REACHABLE + + $ ip -6 neigh show vrf red + 2002:1::64 dev eth1 lladdr a6:d9:c7:4f:06:23 REACHABLE + + +6. Show Addresses for a VRF + + To show addresses for interfaces associated with a VRF add the master + option to the ip command:: + + $ ip addr show vrf NAME + $ ip addr show master NAME + + For example:: + + $ ip addr show vrf red + 3: eth1: mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 + link/ether 02:00:00:00:02:02 brd ff:ff:ff:ff:ff:ff + inet 10.2.1.2/24 brd 10.2.1.255 scope global eth1 + valid_lft forever preferred_lft forever + inet6 2002:1::2/120 scope global + valid_lft forever preferred_lft forever + inet6 fe80::ff:fe00:202/64 scope link + valid_lft forever preferred_lft forever + 4: eth2: mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 + link/ether 02:00:00:00:02:03 brd ff:ff:ff:ff:ff:ff + inet 10.2.2.2/24 brd 10.2.2.255 scope global eth2 + valid_lft forever preferred_lft forever + inet6 2002:2::2/120 scope global + valid_lft forever preferred_lft forever + inet6 fe80::ff:fe00:203/64 scope link + valid_lft forever preferred_lft forever + 7: eth5: mtu 1500 qdisc noop master red state DOWN group default qlen 1000 + link/ether 02:00:00:00:02:06 brd ff:ff:ff:ff:ff:ff + + Or in brief format:: + + $ ip -br addr show vrf red + eth1 UP 10.2.1.2/24 2002:1::2/120 fe80::ff:fe00:202/64 + eth2 UP 10.2.2.2/24 2002:2::2/120 fe80::ff:fe00:203/64 + eth5 DOWN + + +7. Show Routes for a VRF + + To show routes for a VRF use the ip command to display the table associated + with the VRF device:: + + $ ip [-6] route show vrf NAME + $ ip [-6] route show table ID + + For example:: + + $ ip route show vrf red + unreachable default metric 4278198272 + broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2 + 10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2 + local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2 + broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2 + broadcast 10.2.2.0 dev eth2 proto kernel scope link src 10.2.2.2 + 10.2.2.0/24 dev eth2 proto kernel scope link src 10.2.2.2 + local 10.2.2.2 dev eth2 proto kernel scope host src 10.2.2.2 + broadcast 10.2.2.255 dev eth2 proto kernel scope link src 10.2.2.2 + + $ ip -6 route show vrf red + local 2002:1:: dev lo proto none metric 0 pref medium + local 2002:1::2 dev lo proto none metric 0 pref medium + 2002:1::/120 dev eth1 proto kernel metric 256 pref medium + local 2002:2:: dev lo proto none metric 0 pref medium + local 2002:2::2 dev lo proto none metric 0 pref medium + 2002:2::/120 dev eth2 proto kernel metric 256 pref medium + local fe80:: dev lo proto none metric 0 pref medium + local fe80:: dev lo proto none metric 0 pref medium + local fe80::ff:fe00:202 dev lo proto none metric 0 pref medium + local fe80::ff:fe00:203 dev lo proto none metric 0 pref medium + fe80::/64 dev eth1 proto kernel metric 256 pref medium + fe80::/64 dev eth2 proto kernel metric 256 pref medium + ff00::/8 dev red metric 256 pref medium + ff00::/8 dev eth1 metric 256 pref medium + ff00::/8 dev eth2 metric 256 pref medium + unreachable default dev lo metric 4278198272 error -101 pref medium + +8. Route Lookup for a VRF + + A test route lookup can be done for a VRF:: + + $ ip [-6] route get vrf NAME ADDRESS + $ ip [-6] route get oif NAME ADDRESS + + For example:: + + $ ip route get 10.2.1.40 vrf red + 10.2.1.40 dev eth1 table red src 10.2.1.2 + cache + + $ ip -6 route get 2002:1::32 vrf red + 2002:1::32 from :: dev eth1 table red proto kernel src 2002:1::2 metric 256 pref medium + + +9. Removing Network Interface from a VRF + + Network interfaces are removed from a VRF by breaking the enslavement to + the VRF device:: + + $ ip link set dev NAME nomaster + + Connected routes are moved back to the default table and local entries are + moved to the local table. + + For example:: + + $ ip link set dev eth0 nomaster + +-------------------------------------------------------------------------------- + +Commands used in this example:: + + cat >> /etc/iproute2/rt_tables.d/vrf.conf < route table 10 - +-----------------------------+ - | | | - +------+ +------+ +-------------+ - | eth1 | | eth2 | ... | bond1 | - +------+ +------+ +-------------+ - | | - +------+ +------+ - | eth8 | | eth9 | - +------+ +------+ - -Packets received on an enslaved device and are switched to the VRF device -in the IPv4 and IPv6 processing stacks giving the impression that packets -flow through the VRF device. Similarly on egress routing rules are used to -send packets to the VRF device driver before getting sent out the actual -interface. This allows tcpdump on a VRF device to capture all packets into -and out of the VRF as a whole.[1] Similarly, netfilter[2] and tc rules can be -applied using the VRF device to specify rules that apply to the VRF domain -as a whole. - -[1] Packets in the forwarded state do not flow through the device, so those - packets are not seen by tcpdump. Will revisit this limitation in a - future release. - -[2] Iptables on ingress supports PREROUTING with skb->dev set to the real - ingress device and both INPUT and PREROUTING rules with skb->dev set to - the VRF device. For egress POSTROUTING and OUTPUT rules can be written - using either the VRF device or real egress device. - -Setup ------ -1. VRF device is created with an association to a FIB table. - e.g, ip link add vrf-blue type vrf table 10 - ip link set dev vrf-blue up - -2. An l3mdev FIB rule directs lookups to the table associated with the device. - A single l3mdev rule is sufficient for all VRFs. The VRF device adds the - l3mdev rule for IPv4 and IPv6 when the first device is created with a - default preference of 1000. Users may delete the rule if desired and add - with a different priority or install per-VRF rules. - - Prior to the v4.8 kernel iif and oif rules are needed for each VRF device: - ip ru add oif vrf-blue table 10 - ip ru add iif vrf-blue table 10 - -3. Set the default route for the table (and hence default route for the VRF). - ip route add table 10 unreachable default metric 4278198272 - - This high metric value ensures that the default unreachable route can - be overridden by a routing protocol suite. FRRouting interprets - kernel metrics as a combined admin distance (upper byte) and priority - (lower 3 bytes). Thus the above metric translates to [255/8192]. - -4. Enslave L3 interfaces to a VRF device. - ip link set dev eth1 master vrf-blue - - Local and connected routes for enslaved devices are automatically moved to - the table associated with VRF device. Any additional routes depending on - the enslaved device are dropped and will need to be reinserted to the VRF - FIB table following the enslavement. - - The IPv6 sysctl option keep_addr_on_down can be enabled to keep IPv6 global - addresses as VRF enslavement changes. - sysctl -w net.ipv6.conf.all.keep_addr_on_down=1 - -5. Additional VRF routes are added to associated table. - ip route add table 10 ... - - -Applications ------------- -Applications that are to work within a VRF need to bind their socket to the -VRF device: - - setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1); - -or to specify the output device using cmsg and IP_PKTINFO. - -By default the scope of the port bindings for unbound sockets is -limited to the default VRF. That is, it will not be matched by packets -arriving on interfaces enslaved to an l3mdev and processes may bind to -the same port if they bind to an l3mdev. - -TCP & UDP services running in the default VRF context (ie., not bound -to any VRF device) can work across all VRF domains by enabling the -tcp_l3mdev_accept and udp_l3mdev_accept sysctl options: - - sysctl -w net.ipv4.tcp_l3mdev_accept=1 - sysctl -w net.ipv4.udp_l3mdev_accept=1 - -These options are disabled by default so that a socket in a VRF is only -selected for packets in that VRF. There is a similar option for RAW -sockets, which is enabled by default for reasons of backwards compatibility. -This is so as to specify the output device with cmsg and IP_PKTINFO, but -using a socket not bound to the corresponding VRF. This allows e.g. older ping -implementations to be run with specifying the device but without executing it -in the VRF. This option can be disabled so that packets received in a VRF -context are only handled by a raw socket bound to the VRF, and packets in the -default VRF are only handled by a socket not bound to any VRF: - - sysctl -w net.ipv4.raw_l3mdev_accept=0 - -netfilter rules on the VRF device can be used to limit access to services -running in the default VRF context as well. - -################################################################################ - -Using iproute2 for VRFs -======================= -iproute2 supports the vrf keyword as of v4.7. For backwards compatibility this -section lists both commands where appropriate -- with the vrf keyword and the -older form without it. - -1. Create a VRF - - To instantiate a VRF device and associate it with a table: - $ ip link add dev NAME type vrf table ID - - As of v4.8 the kernel supports the l3mdev FIB rule where a single rule - covers all VRFs. The l3mdev rule is created for IPv4 and IPv6 on first - device create. - -2. List VRFs - - To list VRFs that have been created: - $ ip [-d] link show type vrf - NOTE: The -d option is needed to show the table id - - For example: - $ ip -d link show type vrf - 11: mgmt: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 - link/ether 72:b3:ba:91:e2:24 brd ff:ff:ff:ff:ff:ff promiscuity 0 - vrf table 1 addrgenmode eui64 - 12: red: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 - link/ether b6:6f:6e:f6:da:73 brd ff:ff:ff:ff:ff:ff promiscuity 0 - vrf table 10 addrgenmode eui64 - 13: blue: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 - link/ether 36:62:e8:7d:bb:8c brd ff:ff:ff:ff:ff:ff promiscuity 0 - vrf table 66 addrgenmode eui64 - 14: green: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 - link/ether e6:28:b8:63:70:bb brd ff:ff:ff:ff:ff:ff promiscuity 0 - vrf table 81 addrgenmode eui64 - - - Or in brief output: - - $ ip -br link show type vrf - mgmt UP 72:b3:ba:91:e2:24 - red UP b6:6f:6e:f6:da:73 - blue UP 36:62:e8:7d:bb:8c - green UP e6:28:b8:63:70:bb - - -3. Assign a Network Interface to a VRF - - Network interfaces are assigned to a VRF by enslaving the netdevice to a - VRF device: - $ ip link set dev NAME master NAME - - On enslavement connected and local routes are automatically moved to the - table associated with the VRF device. - - For example: - $ ip link set dev eth0 master mgmt - - -4. Show Devices Assigned to a VRF - - To show devices that have been assigned to a specific VRF add the master - option to the ip command: - $ ip link show vrf NAME - $ ip link show master NAME - - For example: - $ ip link show vrf red - 3: eth1: mtu 1500 qdisc pfifo_fast master red state UP mode DEFAULT group default qlen 1000 - link/ether 02:00:00:00:02:02 brd ff:ff:ff:ff:ff:ff - 4: eth2: mtu 1500 qdisc pfifo_fast master red state UP mode DEFAULT group default qlen 1000 - link/ether 02:00:00:00:02:03 brd ff:ff:ff:ff:ff:ff - 7: eth5: mtu 1500 qdisc noop master red state DOWN mode DEFAULT group default qlen 1000 - link/ether 02:00:00:00:02:06 brd ff:ff:ff:ff:ff:ff - - - Or using the brief output: - $ ip -br link show vrf red - eth1 UP 02:00:00:00:02:02 - eth2 UP 02:00:00:00:02:03 - eth5 DOWN 02:00:00:00:02:06 - - -5. Show Neighbor Entries for a VRF - - To list neighbor entries associated with devices enslaved to a VRF device - add the master option to the ip command: - $ ip [-6] neigh show vrf NAME - $ ip [-6] neigh show master NAME - - For example: - $ ip neigh show vrf red - 10.2.1.254 dev eth1 lladdr a6:d9:c7:4f:06:23 REACHABLE - 10.2.2.254 dev eth2 lladdr 5e:54:01:6a:ee:80 REACHABLE - - $ ip -6 neigh show vrf red - 2002:1::64 dev eth1 lladdr a6:d9:c7:4f:06:23 REACHABLE - - -6. Show Addresses for a VRF - - To show addresses for interfaces associated with a VRF add the master - option to the ip command: - $ ip addr show vrf NAME - $ ip addr show master NAME - - For example: - $ ip addr show vrf red - 3: eth1: mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 - link/ether 02:00:00:00:02:02 brd ff:ff:ff:ff:ff:ff - inet 10.2.1.2/24 brd 10.2.1.255 scope global eth1 - valid_lft forever preferred_lft forever - inet6 2002:1::2/120 scope global - valid_lft forever preferred_lft forever - inet6 fe80::ff:fe00:202/64 scope link - valid_lft forever preferred_lft forever - 4: eth2: mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000 - link/ether 02:00:00:00:02:03 brd ff:ff:ff:ff:ff:ff - inet 10.2.2.2/24 brd 10.2.2.255 scope global eth2 - valid_lft forever preferred_lft forever - inet6 2002:2::2/120 scope global - valid_lft forever preferred_lft forever - inet6 fe80::ff:fe00:203/64 scope link - valid_lft forever preferred_lft forever - 7: eth5: mtu 1500 qdisc noop master red state DOWN group default qlen 1000 - link/ether 02:00:00:00:02:06 brd ff:ff:ff:ff:ff:ff - - Or in brief format: - $ ip -br addr show vrf red - eth1 UP 10.2.1.2/24 2002:1::2/120 fe80::ff:fe00:202/64 - eth2 UP 10.2.2.2/24 2002:2::2/120 fe80::ff:fe00:203/64 - eth5 DOWN - - -7. Show Routes for a VRF - - To show routes for a VRF use the ip command to display the table associated - with the VRF device: - $ ip [-6] route show vrf NAME - $ ip [-6] route show table ID - - For example: - $ ip route show vrf red - unreachable default metric 4278198272 - broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2 - 10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2 - local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2 - broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2 - broadcast 10.2.2.0 dev eth2 proto kernel scope link src 10.2.2.2 - 10.2.2.0/24 dev eth2 proto kernel scope link src 10.2.2.2 - local 10.2.2.2 dev eth2 proto kernel scope host src 10.2.2.2 - broadcast 10.2.2.255 dev eth2 proto kernel scope link src 10.2.2.2 - - $ ip -6 route show vrf red - local 2002:1:: dev lo proto none metric 0 pref medium - local 2002:1::2 dev lo proto none metric 0 pref medium - 2002:1::/120 dev eth1 proto kernel metric 256 pref medium - local 2002:2:: dev lo proto none metric 0 pref medium - local 2002:2::2 dev lo proto none metric 0 pref medium - 2002:2::/120 dev eth2 proto kernel metric 256 pref medium - local fe80:: dev lo proto none metric 0 pref medium - local fe80:: dev lo proto none metric 0 pref medium - local fe80::ff:fe00:202 dev lo proto none metric 0 pref medium - local fe80::ff:fe00:203 dev lo proto none metric 0 pref medium - fe80::/64 dev eth1 proto kernel metric 256 pref medium - fe80::/64 dev eth2 proto kernel metric 256 pref medium - ff00::/8 dev red metric 256 pref medium - ff00::/8 dev eth1 metric 256 pref medium - ff00::/8 dev eth2 metric 256 pref medium - unreachable default dev lo metric 4278198272 error -101 pref medium - -8. Route Lookup for a VRF - - A test route lookup can be done for a VRF: - $ ip [-6] route get vrf NAME ADDRESS - $ ip [-6] route get oif NAME ADDRESS - - For example: - $ ip route get 10.2.1.40 vrf red - 10.2.1.40 dev eth1 table red src 10.2.1.2 - cache - - $ ip -6 route get 2002:1::32 vrf red - 2002:1::32 from :: dev eth1 table red proto kernel src 2002:1::2 metric 256 pref medium - - -9. Removing Network Interface from a VRF - - Network interfaces are removed from a VRF by breaking the enslavement to - the VRF device: - $ ip link set dev NAME nomaster - - Connected routes are moved back to the default table and local entries are - moved to the local table. - - For example: - $ ip link set dev eth0 nomaster - --------------------------------------------------------------------------------- - -Commands used in this example: - -cat >> /etc/iproute2/rt_tables.d/vrf.conf < M: Shrijeet Mukherjee L: netdev@vger.kernel.org S: Maintained -F: Documentation/networking/vrf.txt +F: Documentation/networking/vrf.rst F: drivers/net/vrf.c VSPRINTF