[MIPS] PMC MSP71xx core platform

Patch to add core platform support for the PMC-Sierra MSP71xx devices.

Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This commit is contained in:
Marc St-Jean 2007-06-14 15:54:47 -06:00 committed by Ralf Baechle
parent a4b156d47d
commit 35832e26f9
16 changed files with 3083 additions and 0 deletions

View File

@ -0,0 +1,11 @@
#
# Makefile for the PMC-Sierra MSP SOCs
#
obj-y += msp_prom.o msp_setup.o msp_irq.o \
msp_time.o msp_serial.o msp_elb.o
obj-$(CONFIG_PMC_MSP7120_GW) += msp_hwbutton.o
obj-$(CONFIG_IRQ_MSP_SLP) += msp_irq_slp.o
obj-$(CONFIG_IRQ_MSP_CIC) += msp_irq_cic.o
obj-$(CONFIG_PCI) += msp_pci.o
obj-$(CONFIG_MSPETH) += msp_eth.o
obj-$(CONFIG_USB_MSP71XX) += msp_usb.o

View File

@ -0,0 +1,46 @@
/*
* Sets up the proper Chip Select configuration registers. It is assumed that
* PMON sets up the ADDR and MASK registers properly.
*
* Copyright 2005-2006 PMC-Sierra, Inc.
* Author: Marc St-Jean, Marc_St-Jean@pmc-sierra.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <msp_regs.h>
static int __init msp_elb_setup(void)
{
#if defined(CONFIG_PMC_MSP7120_GW) \
|| defined(CONFIG_PMC_MSP7120_EVAL)
/*
* Force all CNFG to be identical and equal to CS0,
* according to OPS doc
*/
*CS1_CNFG_REG = *CS2_CNFG_REG = *CS3_CNFG_REG = *CS0_CNFG_REG;
#endif
return 0;
}
subsys_initcall(msp_elb_setup);

View File

@ -0,0 +1,179 @@
/*
* Sets up interrupt handlers for various hardware switches which are
* connected to interrupt lines.
*
* Copyright 2005-2207 PMC-Sierra, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <msp_int.h>
#include <msp_regs.h>
#include <msp_regops.h>
#ifdef CONFIG_PMCTWILED
#include <msp_led_macros.h>
#endif
/* For hwbutton_interrupt->initial_state */
#define HWBUTTON_HI 0x1
#define HWBUTTON_LO 0x2
/*
* This struct describes a hardware button
*/
struct hwbutton_interrupt {
char *name; /* Name of button */
int irq; /* Actual LINUX IRQ */
int eirq; /* Extended IRQ number (0-7) */
int initial_state; /* The "normal" state of the switch */
void (*handle_hi)(void *); /* Handler: switch input has gone HI */
void (*handle_lo)(void *); /* Handler: switch input has gone LO */
void *data; /* Optional data to pass to handler */
};
#ifdef CONFIG_PMC_MSP7120_GW
extern void msp_restart(char *);
static void softreset_push(void *data)
{
printk(KERN_WARNING "SOFTRESET switch was pushed\n");
/*
* In the future you could move this to the release handler,
* timing the difference between the 'push' and 'release', and only
* doing this ungraceful restart if the button has been down for
* a certain amount of time; otherwise doing a graceful restart.
*/
msp_restart(NULL);
}
static void softreset_release(void *data)
{
printk(KERN_WARNING "SOFTRESET switch was released\n");
/* Do nothing */
}
static void standby_on(void *data)
{
printk(KERN_WARNING "STANDBY switch was set to ON (not implemented)\n");
/* TODO: Put board in standby mode */
#ifdef CONFIG_PMCTWILED
msp_led_turn_off(MSP_LED_PWRSTANDBY_GREEN);
msp_led_turn_on(MSP_LED_PWRSTANDBY_RED);
#endif
}
static void standby_off(void *data)
{
printk(KERN_WARNING
"STANDBY switch was set to OFF (not implemented)\n");
/* TODO: Take out of standby mode */
#ifdef CONFIG_PMCTWILED
msp_led_turn_on(MSP_LED_PWRSTANDBY_GREEN);
msp_led_turn_off(MSP_LED_PWRSTANDBY_RED);
#endif
}
static struct hwbutton_interrupt softreset_sw = {
.name = "Softreset button",
.irq = MSP_INT_EXT0,
.eirq = 0,
.initial_state = HWBUTTON_HI,
.handle_hi = softreset_release,
.handle_lo = softreset_push,
.data = NULL,
};
static struct hwbutton_interrupt standby_sw = {
.name = "Standby switch",
.irq = MSP_INT_EXT1,
.eirq = 1,
.initial_state = HWBUTTON_HI,
.handle_hi = standby_off,
.handle_lo = standby_on,
.data = NULL,
};
#endif /* CONFIG_PMC_MSP7120_GW */
static irqreturn_t hwbutton_handler(int irq, void *data)
{
struct hwbutton_interrupt *hirq = data;
unsigned long cic_ext = *CIC_EXT_CFG_REG;
if (irq != hirq->irq)
return IRQ_NONE;
if (CIC_EXT_IS_ACTIVE_HI(cic_ext, hirq->eirq)) {
/* Interrupt: pin is now HI */
CIC_EXT_SET_ACTIVE_LO(cic_ext, hirq->eirq);
hirq->handle_hi(hirq->data);
} else {
/* Interrupt: pin is now LO */
CIC_EXT_SET_ACTIVE_HI(cic_ext, hirq->eirq);
hirq->handle_lo(hirq->data);
}
/*
* Invert the POLARITY of this level interrupt to ack the interrupt
* Thus next state change will invoke the opposite message
*/
*CIC_EXT_CFG_REG = cic_ext;
return IRQ_HANDLED;
}
static int msp_hwbutton_register(struct hwbutton_interrupt *hirq)
{
unsigned long cic_ext;
if (hirq->handle_hi == NULL || hirq->handle_lo == NULL)
return -EINVAL;
cic_ext = *CIC_EXT_CFG_REG;
CIC_EXT_SET_TRIGGER_LEVEL(cic_ext, hirq->eirq);
if (hirq->initial_state == HWBUTTON_HI)
CIC_EXT_SET_ACTIVE_LO(cic_ext, hirq->eirq);
else
CIC_EXT_SET_ACTIVE_HI(cic_ext, hirq->eirq);
*CIC_EXT_CFG_REG = cic_ext;
return request_irq(hirq->irq, hwbutton_handler, SA_INTERRUPT,
hirq->name, (void *)hirq);
}
static int __init msp_hwbutton_setup(void)
{
#ifdef CONFIG_PMC_MSP7120_GW
msp_hwbutton_register(&softreset_sw);
msp_hwbutton_register(&standby_sw);
#endif
return 0;
}
subsys_initcall(msp_hwbutton_setup);

View File

@ -0,0 +1,124 @@
/*
* IRQ vector handles
*
* Copyright (C) 1995, 1996, 1997, 2003 by Ralf Baechle
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/ptrace.h>
#include <linux/time.h>
#include <asm/irq_cpu.h>
#include <msp_int.h>
extern void msp_int_handle(void);
/* SLP bases systems */
extern void msp_slp_irq_init(void);
extern void msp_slp_irq_dispatch(void);
/* CIC based systems */
extern void msp_cic_irq_init(void);
extern void msp_cic_irq_dispatch(void);
/*
* The PMC-Sierra MSP interrupts are arranged in a 3 level cascaded
* hierarchical system. The first level are the direct MIPS interrupts
* and are assigned the interrupt range 0-7. The second level is the SLM
* interrupt controller and is assigned the range 8-39. The third level
* comprises the Peripherial block, the PCI block, the PCI MSI block and
* the SLP. The PCI interrupts and the SLP errors are handled by the
* relevant subsystems so the core interrupt code needs only concern
* itself with the Peripheral block. These are assigned interrupts in
* the range 40-71.
*/
asmlinkage void plat_irq_dispatch(struct pt_regs *regs)
{
u32 pending;
pending = read_c0_status() & read_c0_cause();
/*
* jump to the correct interrupt routine
* These are arranged in priority order and the timer
* comes first!
*/
#ifdef CONFIG_IRQ_MSP_CIC /* break out the CIC stuff for now */
if (pending & C_IRQ4) /* do the peripherals first, that's the timer */
msp_cic_irq_dispatch();
else if (pending & C_IRQ0)
do_IRQ(MSP_INT_MAC0);
else if (pending & C_IRQ1)
do_IRQ(MSP_INT_MAC1);
else if (pending & C_IRQ2)
do_IRQ(MSP_INT_USB);
else if (pending & C_IRQ3)
do_IRQ(MSP_INT_SAR);
else if (pending & C_IRQ5)
do_IRQ(MSP_INT_SEC);
#else
if (pending & C_IRQ5)
do_IRQ(MSP_INT_TIMER);
else if (pending & C_IRQ0)
do_IRQ(MSP_INT_MAC0);
else if (pending & C_IRQ1)
do_IRQ(MSP_INT_MAC1);
else if (pending & C_IRQ3)
do_IRQ(MSP_INT_VE);
else if (pending & C_IRQ4)
msp_slp_irq_dispatch();
#endif
else if (pending & C_SW0) /* do software after hardware */
do_IRQ(MSP_INT_SW0);
else if (pending & C_SW1)
do_IRQ(MSP_INT_SW1);
}
static struct irqaction cascade_msp = {
.handler = no_action,
.name = "MSP cascade"
};
void __init arch_init_irq(void)
{
/* initialize the 1st-level CPU based interrupt controller */
mips_cpu_irq_init();
#ifdef CONFIG_IRQ_MSP_CIC
msp_cic_irq_init();
/* setup the cascaded interrupts */
setup_irq(MSP_INT_CIC, &cascade_msp);
setup_irq(MSP_INT_PER, &cascade_msp);
#else
/* setup the 2nd-level SLP register based interrupt controller */
msp_slp_irq_init();
/* setup the cascaded SLP/PER interrupts */
setup_irq(MSP_INT_SLP, &cascade_msp);
setup_irq(MSP_INT_PER, &cascade_msp);
#endif
}

View File

@ -0,0 +1,134 @@
/*
* This file define the irq handler for MSP SLM subsystem interrupts.
*
* Copyright 2005-2007 PMC-Sierra, Inc, derived from irq_cpu.c
* Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/bitops.h>
#include <asm/system.h>
#include <msp_cic_int.h>
#include <msp_regs.h>
/*
* NOTE: We are only enabling support for VPE0 right now.
*/
static inline void unmask_msp_cic_irq(unsigned int irq)
{
/* check for PER interrupt range */
if (irq < MSP_PER_INTBASE)
*CIC_VPE0_MSK_REG |= (1 << (irq - MSP_CIC_INTBASE));
else
*PER_INT_MSK_REG |= (1 << (irq - MSP_PER_INTBASE));
}
static inline void mask_msp_cic_irq(unsigned int irq)
{
/* check for PER interrupt range */
if (irq < MSP_PER_INTBASE)
*CIC_VPE0_MSK_REG &= ~(1 << (irq - MSP_CIC_INTBASE));
else
*PER_INT_MSK_REG &= ~(1 << (irq - MSP_PER_INTBASE));
}
/*
* While we ack the interrupt interrupts are disabled and thus we don't need
* to deal with concurrency issues. Same for msp_cic_irq_end.
*/
static inline void ack_msp_cic_irq(unsigned int irq)
{
mask_msp_cic_irq(irq);
/*
* only really necessary for 18, 16-14 and sometimes 3:0 (since
* these can be edge sensitive) but it doesn't hurt for the others.
*/
/* check for PER interrupt range */
if (irq < MSP_PER_INTBASE)
*CIC_STS_REG = (1 << (irq - MSP_CIC_INTBASE));
else
*PER_INT_STS_REG = (1 << (irq - MSP_PER_INTBASE));
}
static struct irq_chip msp_cic_irq_controller = {
.name = "MSP_CIC",
.ack = ack_msp_cic_irq,
.mask = ack_msp_cic_irq,
.mask_ack = ack_msp_cic_irq,
.unmask = unmask_msp_cic_irq,
};
void __init msp_cic_irq_init(void)
{
int i;
/* Mask/clear interrupts. */
*CIC_VPE0_MSK_REG = 0x00000000;
*PER_INT_MSK_REG = 0x00000000;
*CIC_STS_REG = 0xFFFFFFFF;
*PER_INT_STS_REG = 0xFFFFFFFF;
#if defined(CONFIG_PMC_MSP7120_GW) || \
defined(CONFIG_PMC_MSP7120_EVAL)
/*
* The MSP7120 RG and EVBD boards use IRQ[6:4] for PCI.
* These inputs map to EXT_INT_POL[6:4] inside the CIC.
* They are to be active low, level sensitive.
*/
*CIC_EXT_CFG_REG &= 0xFFFF8F8F;
#endif
/* initialize all the IRQ descriptors */
for (i = MSP_CIC_INTBASE; i < MSP_PER_INTBASE + 32; i++)
set_irq_chip_and_handler(i, &msp_cic_irq_controller,
handle_level_irq);
}
void msp_cic_irq_dispatch(void)
{
u32 pending;
int intbase;
intbase = MSP_CIC_INTBASE;
pending = *CIC_STS_REG & *CIC_VPE0_MSK_REG;
/* check for PER interrupt */
if (pending == (1 << (MSP_INT_PER - MSP_CIC_INTBASE))) {
intbase = MSP_PER_INTBASE;
pending = *PER_INT_STS_REG & *PER_INT_MSK_REG;
}
/* check for spurious interrupt */
if (pending == 0x00000000) {
printk(KERN_ERR
"Spurious %s interrupt? status %08x, mask %08x\n",
(intbase == MSP_CIC_INTBASE) ? "CIC" : "PER",
(intbase == MSP_CIC_INTBASE) ?
*CIC_STS_REG : *PER_INT_STS_REG,
(intbase == MSP_CIC_INTBASE) ?
*CIC_VPE0_MSK_REG : *PER_INT_MSK_REG);
return;
}
/* check for the timer and dispatch it first */
if ((intbase == MSP_CIC_INTBASE) &&
(pending & (1 << (MSP_INT_VPE0_TIMER - MSP_CIC_INTBASE))))
do_IRQ(MSP_INT_VPE0_TIMER);
else
do_IRQ(ffs(pending) + intbase - 1);
}

View File

@ -0,0 +1,109 @@
/*
* This file define the irq handler for MSP SLM subsystem interrupts.
*
* Copyright 2005-2006 PMC-Sierra, Inc, derived from irq_cpu.c
* Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/bitops.h>
#include <asm/mipsregs.h>
#include <asm/system.h>
#include <msp_slp_int.h>
#include <msp_regs.h>
static inline void unmask_msp_slp_irq(unsigned int irq)
{
/* check for PER interrupt range */
if (irq < MSP_PER_INTBASE)
*SLP_INT_MSK_REG |= (1 << (irq - MSP_SLP_INTBASE));
else
*PER_INT_MSK_REG |= (1 << (irq - MSP_PER_INTBASE));
}
static inline void mask_msp_slp_irq(unsigned int irq)
{
/* check for PER interrupt range */
if (irq < MSP_PER_INTBASE)
*SLP_INT_MSK_REG &= ~(1 << (irq - MSP_SLP_INTBASE));
else
*PER_INT_MSK_REG &= ~(1 << (irq - MSP_PER_INTBASE));
}
/*
* While we ack the interrupt interrupts are disabled and thus we don't need
* to deal with concurrency issues. Same for msp_slp_irq_end.
*/
static inline void ack_msp_slp_irq(unsigned int irq)
{
mask_slp_irq(irq);
/*
* only really necessary for 18, 16-14 and sometimes 3:0 (since
* these can be edge sensitive) but it doesn't hurt for the others.
*/
/* check for PER interrupt range */
if (irq < MSP_PER_INTBASE)
*SLP_INT_STS_REG = (1 << (irq - MSP_SLP_INTBASE));
else
*PER_INT_STS_REG = (1 << (irq - MSP_PER_INTBASE));
}
static struct irq_chip msp_slp_irq_controller = {
.name = "MSP_SLP",
.ack = ack_msp_slp_irq,
.mask = ack_msp_slp_irq,
.mask_ack = ack_msp_slp_irq,
.unmask = unmask_msp_slp_irq,
};
void __init msp_slp_irq_init(void)
{
int i;
/* Mask/clear interrupts. */
*SLP_INT_MSK_REG = 0x00000000;
*PER_INT_MSK_REG = 0x00000000;
*SLP_INT_STS_REG = 0xFFFFFFFF;
*PER_INT_STS_REG = 0xFFFFFFFF;
/* initialize all the IRQ descriptors */
for (i = MSP_SLP_INTBASE; i < MSP_PER_INTBASE + 32; i++)
set_irq_chip_and_handler(i, &msp_slp_irq_controller
handle_level_irq);
}
void msp_slp_irq_dispatch(void)
{
u32 pending;
int intbase;
intbase = MSP_SLP_INTBASE;
pending = *SLP_INT_STS_REG & *SLP_INT_MSK_REG;
/* check for PER interrupt */
if (pending == (1 << (MSP_INT_PER - MSP_SLP_INTBASE))) {
intbase = MSP_PER_INTBASE;
pending = *PER_INT_STS_REG & *PER_INT_MSK_REG;
}
/* check for spurious interrupt */
if (pending == 0x00000000) {
printk(KERN_ERR "Spurious %s interrupt?\n",
(intbase == MSP_SLP_INTBASE) ? "SLP" : "PER");
return;
}
/* dispatch the irq */
do_IRQ(ffs(pending) + intbase - 1);
}

View File

@ -0,0 +1,566 @@
/*
* BRIEF MODULE DESCRIPTION
* PROM library initialisation code, assuming a version of
* pmon is the boot code.
*
* Copyright 2000,2001 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
* ppopov@mvista.com or source@mvista.com
*
* This file was derived from Carsten Langgaard's
* arch/mips/mips-boards/xx files.
*
* Carsten Langgaard, carstenl@mips.com
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/mm.h>
#ifdef CONFIG_CRAMFS
#include <linux/cramfs_fs.h>
#endif
#ifdef CONFIG_SQUASHFS
#include <linux/squashfs_fs.h>
#endif
#include <asm/addrspace.h>
#include <asm/bootinfo.h>
#include <asm-generic/sections.h>
#include <asm/page.h>
#include <msp_prom.h>
#include <msp_regs.h>
/* global PROM environment variables and pointers */
int prom_argc;
char **prom_argv, **prom_envp;
int *prom_vec;
/* debug flag */
int init_debug = 1;
/* memory blocks */
struct prom_pmemblock mdesc[PROM_MAX_PMEMBLOCKS];
/* default feature sets */
static char msp_default_features[] =
#if defined(CONFIG_PMC_MSP4200_EVAL) \
|| defined(CONFIG_PMC_MSP4200_GW)
"ERER";
#elif defined(CONFIG_PMC_MSP7120_EVAL) \
|| defined(CONFIG_PMC_MSP7120_GW)
"EMEMSP";
#elif defined(CONFIG_PMC_MSP7120_FPGA)
"EMEM";
#endif
/* conversion functions */
static inline unsigned char str2hexnum(unsigned char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
return 0; /* foo */
}
static inline int str2eaddr(unsigned char *ea, unsigned char *str)
{
int index = 0;
unsigned char num = 0;
while (*str != '\0') {
if ((*str == '.') || (*str == ':')) {
ea[index++] = num;
num = 0;
str++;
} else {
num = num << 4;
num |= str2hexnum(*str++);
}
}
if (index == 5) {
ea[index++] = num;
return 0;
} else
return -1;
}
EXPORT_SYMBOL(str2eaddr);
static inline unsigned long str2hex(unsigned char *str)
{
int value = 0;
while (*str) {
value = value << 4;
value |= str2hexnum(*str++);
}
return value;
}
/* function to query the system information */
const char *get_system_type(void)
{
#if defined(CONFIG_PMC_MSP4200_EVAL)
return "PMC-Sierra MSP4200 Eval Board";
#elif defined(CONFIG_PMC_MSP4200_GW)
return "PMC-Sierra MSP4200 VoIP Gateway";
#elif defined(CONFIG_PMC_MSP7120_EVAL)
return "PMC-Sierra MSP7120 Eval Board";
#elif defined(CONFIG_PMC_MSP7120_GW)
return "PMC-Sierra MSP7120 Residential Gateway";
#elif defined(CONFIG_PMC_MSP7120_FPGA)
return "PMC-Sierra MSP7120 FPGA";
#else
#error "What is the type of *your* MSP?"
#endif
}
int get_ethernet_addr(char *ethaddr_name, char *ethernet_addr)
{
char *ethaddr_str;
ethaddr_str = prom_getenv(ethaddr_name);
if (!ethaddr_str) {
printk(KERN_WARNING "%s not set in boot prom\n", ethaddr_name);
return -1;
}
if (str2eaddr(ethernet_addr, ethaddr_str) == -1) {
printk(KERN_WARNING "%s badly formatted-<%s>\n",
ethaddr_name, ethaddr_str);
return -1;
}
if (init_debug > 1) {
int i;
printk(KERN_DEBUG "get_ethernet_addr: for %s ", ethaddr_name);
for (i = 0; i < 5; i++)
printk(KERN_DEBUG "%02x:",
(unsigned char)*(ethernet_addr+i));
printk(KERN_DEBUG "%02x\n", *(ethernet_addr+i));
}
return 0;
}
EXPORT_SYMBOL(get_ethernet_addr);
static char *get_features(void)
{
char *feature = prom_getenv(FEATURES);
if (feature == NULL) {
/* default features based on MACHINE_TYPE */
feature = msp_default_features;
}
return feature;
}
static char test_feature(char c)
{
char *feature = get_features();
while (*feature) {
if (*feature++ == c)
return *feature;
feature++;
}
return FEATURE_NOEXIST;
}
unsigned long get_deviceid(void)
{
char *deviceid = prom_getenv(DEVICEID);
if (deviceid == NULL)
return *DEV_ID_REG;
else
return str2hex(deviceid);
}
char identify_pci(void)
{
return test_feature(PCI_KEY);
}
EXPORT_SYMBOL(identify_pci);
char identify_pcimux(void)
{
return test_feature(PCIMUX_KEY);
}
char identify_sec(void)
{
return test_feature(SEC_KEY);
}
EXPORT_SYMBOL(identify_sec);
char identify_spad(void)
{
return test_feature(SPAD_KEY);
}
EXPORT_SYMBOL(identify_spad);
char identify_tdm(void)
{
return test_feature(TDM_KEY);
}
EXPORT_SYMBOL(identify_tdm);
char identify_zsp(void)
{
return test_feature(ZSP_KEY);
}
EXPORT_SYMBOL(identify_zsp);
static char identify_enetfeature(char key, unsigned long interface_num)
{
char *feature = get_features();
while (*feature) {
if (*feature++ == key && interface_num-- == 0)
return *feature;
feature++;
}
return FEATURE_NOEXIST;
}
char identify_enet(unsigned long interface_num)
{
return identify_enetfeature(ENET_KEY, interface_num);
}
EXPORT_SYMBOL(identify_enet);
char identify_enetTxD(unsigned long interface_num)
{
return identify_enetfeature(ENETTXD_KEY, interface_num);
}
EXPORT_SYMBOL(identify_enetTxD);
unsigned long identify_family(void)
{
unsigned long deviceid;
deviceid = get_deviceid();
return deviceid & CPU_DEVID_FAMILY;
}
EXPORT_SYMBOL(identify_family);
unsigned long identify_revision(void)
{
unsigned long deviceid;
deviceid = get_deviceid();
return deviceid & CPU_DEVID_REVISION;
}
EXPORT_SYMBOL(identify_revision);
/* PROM environment functions */
char *prom_getenv(char *env_name)
{
/*
* Return a pointer to the given environment variable. prom_envp
* points to a null terminated array of pointers to variables.
* Environment variables are stored in the form of "memsize=64"
*/
char **var = prom_envp;
int i = strlen(env_name);
while (*var) {
if (strncmp(env_name, *var, i) == 0) {
return (*var + strlen(env_name) + 1);
}
var++;
}
return NULL;
}
/* PROM commandline functions */
char *prom_getcmdline(void)
{
return &(arcs_cmdline[0]);
}
EXPORT_SYMBOL(prom_getcmdline);
void __init prom_init_cmdline(void)
{
char *cp;
int actr;
actr = 1; /* Always ignore argv[0] */
cp = &(arcs_cmdline[0]);
while (actr < prom_argc) {
strcpy(cp, prom_argv[actr]);
cp += strlen(prom_argv[actr]);
*cp++ = ' ';
actr++;
}
if (cp != &(arcs_cmdline[0])) /* get rid of trailing space */
--cp;
*cp = '\0';
}
/* memory allocation functions */
static int __init prom_memtype_classify(unsigned int type)
{
switch (type) {
case yamon_free:
return BOOT_MEM_RAM;
case yamon_prom:
return BOOT_MEM_ROM_DATA;
default:
return BOOT_MEM_RESERVED;
}
}
void __init prom_meminit(void)
{
struct prom_pmemblock *p;
p = prom_getmdesc();
while (p->size) {
long type;
unsigned long base, size;
type = prom_memtype_classify(p->type);
base = p->base;
size = p->size;
add_memory_region(base, size, type);
p++;
}
}
void __init prom_free_prom_memory(void)
{
int argc;
char **argv;
char **envp;
char *ptr;
int len = 0;
int i;
unsigned long addr;
/*
* preserve environment variables and command line from pmon/bbload
* first preserve the command line
*/
for (argc = 0; argc < prom_argc; argc++) {
len += sizeof(char *); /* length of pointer */
len += strlen(prom_argv[argc]) + 1; /* length of string */
}
len += sizeof(char *); /* plus length of null pointer */
argv = kmalloc(len, GFP_KERNEL);
ptr = (char *) &argv[prom_argc + 1]; /* strings follow array */
for (argc = 0; argc < prom_argc; argc++) {
argv[argc] = ptr;
strcpy(ptr, prom_argv[argc]);
ptr += strlen(prom_argv[argc]) + 1;
}
argv[prom_argc] = NULL; /* end array with null pointer */
prom_argv = argv;
/* next preserve the environment variables */
len = 0;
i = 0;
for (envp = prom_envp; *envp != NULL; envp++) {
i++; /* count number of environment variables */
len += sizeof(char *); /* length of pointer */
len += strlen(*envp) + 1; /* length of string */
}
len += sizeof(char *); /* plus length of null pointer */
envp = kmalloc(len, GFP_KERNEL);
ptr = (char *) &envp[i+1];
for (argc = 0; argc < i; argc++) {
envp[argc] = ptr;
strcpy(ptr, prom_envp[argc]);
ptr += strlen(prom_envp[argc]) + 1;
}
envp[i] = NULL; /* end array with null pointer */
prom_envp = envp;
for (i = 0; i < boot_mem_map.nr_map; i++) {
if (boot_mem_map.map[i].type != BOOT_MEM_ROM_DATA)
continue;
addr = boot_mem_map.map[i].addr;
free_init_pages("prom memory",
addr, addr + boot_mem_map.map[i].size);
}
}
struct prom_pmemblock *__init prom_getmdesc(void)
{
static char memsz_env[] __initdata = "memsize";
static char heaptop_env[] __initdata = "heaptop";
char *str;
unsigned int memsize;
unsigned int heaptop;
#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
void *ramroot_start;
unsigned long ramroot_size;
#endif
int i;
str = prom_getenv(memsz_env);
if (!str) {
ppfinit("memsize not set in boot prom, "
"set to default (32Mb)\n");
memsize = 0x02000000;
} else {
memsize = simple_strtol(str, NULL, 0);
if (memsize == 0) {
/* if memsize is a bad size, use reasonable default */
memsize = 0x02000000;
}
/* convert to physical address (removing caching bits, etc) */
memsize = CPHYSADDR(memsize);
}
str = prom_getenv(heaptop_env);
if (!str) {
heaptop = CPHYSADDR((u32)&_text);
ppfinit("heaptop not set in boot prom, "
"set to default 0x%08x\n", heaptop);
} else {
heaptop = simple_strtol(str, NULL, 16);
if (heaptop == 0) {
/* heaptop conversion bad, might have 0xValue */
heaptop = simple_strtol(str, NULL, 0);
if (heaptop == 0) {
/* heaptop still bad, use reasonable default */
heaptop = CPHYSADDR((u32)&_text);
}
}
/* convert to physical address (removing caching bits, etc) */
heaptop = CPHYSADDR((u32)heaptop);
}
/* the base region */
i = 0;
mdesc[i].type = BOOT_MEM_RESERVED;
mdesc[i].base = 0x00000000;
mdesc[i].size = PAGE_ALIGN(0x300 + 0x80);
/* jtag interrupt vector + sizeof vector */
/* PMON data */
if (heaptop > mdesc[i].base + mdesc[i].size) {
i++; /* 1 */
mdesc[i].type = BOOT_MEM_ROM_DATA;
mdesc[i].base = mdesc[i-1].base + mdesc[i-1].size;
mdesc[i].size = heaptop - mdesc[i].base;
}
/* end of PMON data to start of kernel -- probably zero .. */
if (heaptop != CPHYSADDR((u32)_text)) {
i++; /* 2 */
mdesc[i].type = BOOT_MEM_RAM;
mdesc[i].base = heaptop;
mdesc[i].size = CPHYSADDR((u32)_text) - mdesc[i].base;
}
/* kernel proper */
i++; /* 3 */
mdesc[i].type = BOOT_MEM_RESERVED;
mdesc[i].base = CPHYSADDR((u32)_text);
#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
if (get_ramroot(&ramroot_start, &ramroot_size)) {
/*
* Rootfs in RAM -- follows kernel
* Combine rootfs image with kernel block so a
* page (4k) isn't wasted between memory blocks
*/
mdesc[i].size = CPHYSADDR(PAGE_ALIGN(
(u32)ramroot_start + ramroot_size)) - mdesc[i].base;
} else
#endif
mdesc[i].size = CPHYSADDR(PAGE_ALIGN(
(u32)_end)) - mdesc[i].base;
/* Remainder of RAM -- under memsize */
i++; /* 5 */
mdesc[i].type = yamon_free;
mdesc[i].base = mdesc[i-1].base + mdesc[i-1].size;
mdesc[i].size = memsize - mdesc[i].base;
return &mdesc[0];
}
/* rootfs functions */
#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
bool get_ramroot(void **start, unsigned long *size)
{
extern char _end[];
/* Check for start following the end of the kernel */
void *check_start = (void *)_end;
/* Check for supported rootfs types */
#ifdef CONFIG_CRAMFS
if (*(__u32 *)check_start == CRAMFS_MAGIC) {
/* Get CRAMFS size */
*start = check_start;
*size = PAGE_ALIGN(((struct cramfs_super *)
check_start)->size);
return true;
}
#endif
#ifdef CONFIG_SQUASHFS
if (*((unsigned int *)check_start) == SQUASHFS_MAGIC) {
/* Get SQUASHFS size */
*start = check_start;
*size = PAGE_ALIGN(((struct squashfs_super_block *)
check_start)->bytes_used);
return true;
}
#endif
return false;
}
EXPORT_SYMBOL(get_ramroot);
#endif

View File

@ -0,0 +1,256 @@
/*
* The generic setup file for PMC-Sierra MSP processors
*
* Copyright 2005-2007 PMC-Sierra, Inc,
* Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <asm/bootinfo.h>
#include <asm/cacheflush.h>
#include <asm/r4kcache.h>
#include <asm/reboot.h>
#include <asm/time.h>
#include <msp_prom.h>
#include <msp_regs.h>
#if defined(CONFIG_PMC_MSP7120_GW)
#include <msp_regops.h>
#include <msp_gpio.h>
#define MSP_BOARD_RESET_GPIO 9
#endif
extern void msp_timer_init(void);
extern void msp_serial_setup(void);
extern void pmctwiled_setup(void);
#if defined(CONFIG_PMC_MSP7120_EVAL) || \
defined(CONFIG_PMC_MSP7120_GW) || \
defined(CONFIG_PMC_MSP7120_FPGA)
/*
* Performs the reset for MSP7120-based boards
*/
void msp7120_reset(void)
{
void *start, *end, *iptr;
register int i;
/* Diasble all interrupts */
local_irq_disable();
#ifdef CONFIG_SYS_SUPPORTS_MULTITHREADING
dvpe();
#endif
/* Cache the reset code of this function */
__asm__ __volatile__ (
" .set push \n"
" .set mips3 \n"
" la %0,startpoint \n"
" la %1,endpoint \n"
" .set pop \n"
: "=r" (start), "=r" (end)
:
);
for (iptr = (void *)((unsigned int)start & ~(L1_CACHE_BYTES - 1));
iptr < end; iptr += L1_CACHE_BYTES)
cache_op(Fill, iptr);
__asm__ __volatile__ (
"startpoint: \n"
);
/* Put the DDRC into self-refresh mode */
DDRC_INDIRECT_WRITE(DDRC_CTL(10), 0xb, 1 << 16);
/*
* IMPORTANT!
* DO NOT do anything from here on out that might even
* think about fetching from RAM - i.e., don't call any
* non-inlined functions, and be VERY sure that any inline
* functions you do call do NOT access any sort of RAM
* anywhere!
*/
/* Wait a bit for the DDRC to settle */
for (i = 0; i < 100000000; i++);
#if defined(CONFIG_PMC_MSP7120_GW)
/*
* Set GPIO 9 HI, (tied to board reset logic)
* GPIO 9 is the 4th GPIO of register 3
*
* NOTE: We cannot use the higher-level msp_gpio_mode()/out()
* as GPIO char driver may not be enabled and it would look up
* data inRAM!
*/
set_value_reg32(GPIO_CFG3_REG,
basic_mode_mask(MSP_BOARD_RESET_GPIO),
basic_mode(MSP_GPIO_OUTPUT, MSP_BOARD_RESET_GPIO));
set_reg32(GPIO_DATA3_REG,
basic_data_mask(MSP_BOARD_RESET_GPIO));
/*
* In case GPIO9 doesn't reset the board (jumper configurable!)
* fallback to device reset below.
*/
#endif
/* Set bit 1 of the MSP7120 reset register */
*RST_SET_REG = 0x00000001;
__asm__ __volatile__ (
"endpoint: \n"
);
}
#endif
void msp_restart(char *command)
{
printk(KERN_WARNING "Now rebooting .......\n");
#if defined(CONFIG_PMC_MSP7120_EVAL) || \
defined(CONFIG_PMC_MSP7120_GW) || \
defined(CONFIG_PMC_MSP7120_FPGA)
msp7120_reset();
#else
/* No chip-specific reset code, just jump to the ROM reset vector */
set_c0_status(ST0_BEV | ST0_ERL);
change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
flush_cache_all();
write_c0_wired(0);
__asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
#endif
}
void msp_halt(void)
{
printk(KERN_WARNING "\n** You can safely turn off the power\n");
while (1)
/* If possible call official function to get CPU WARs */
if (cpu_wait)
(*cpu_wait)();
else
__asm__(".set\tmips3\n\t" "wait\n\t" ".set\tmips0");
}
void msp_power_off(void)
{
msp_halt();
}
void __init plat_mem_setup(void)
{
_machine_restart = msp_restart;
_machine_halt = msp_halt;
pm_power_off = msp_power_off;
board_time_init = msp_timer_init;
}
void __init prom_init(void)
{
unsigned long family;
unsigned long revision;
prom_argc = fw_arg0;
prom_argv = (char **)fw_arg1;
prom_envp = (char **)fw_arg2;
/*
* Someday we can use this with PMON2000 to get a
* platform call prom routines for output etc. without
* having to use grody hacks. For now it's unused.
*
* struct callvectors *cv = (struct callvectors *) fw_arg3;
*/
family = identify_family();
revision = identify_revision();
switch (family) {
case FAMILY_FPGA:
if (FPGA_IS_MSP4200(revision)) {
/* Old-style revision ID */
mips_machgroup = MACH_GROUP_MSP;
mips_machtype = MACH_MSP4200_FPGA;
} else {
mips_machgroup = MACH_GROUP_MSP;
mips_machtype = MACH_MSP_OTHER;
}
break;
case FAMILY_MSP4200:
mips_machgroup = MACH_GROUP_MSP;
#if defined(CONFIG_PMC_MSP4200_EVAL)
mips_machtype = MACH_MSP4200_EVAL;
#elif defined(CONFIG_PMC_MSP4200_GW)
mips_machtype = MACH_MSP4200_GW;
#else
mips_machtype = MACH_MSP_OTHER;
#endif
break;
case FAMILY_MSP4200_FPGA:
mips_machgroup = MACH_GROUP_MSP;
mips_machtype = MACH_MSP4200_FPGA;
break;
case FAMILY_MSP7100:
mips_machgroup = MACH_GROUP_MSP;
#if defined(CONFIG_PMC_MSP7120_EVAL)
mips_machtype = MACH_MSP7120_EVAL;
#elif defined(CONFIG_PMC_MSP7120_GW)
mips_machtype = MACH_MSP7120_GW;
#else
mips_machtype = MACH_MSP_OTHER;
#endif
break;
case FAMILY_MSP7100_FPGA:
mips_machgroup = MACH_GROUP_MSP;
mips_machtype = MACH_MSP7120_FPGA;
break;
default:
/* we don't recognize the machine */
mips_machgroup = MACH_GROUP_UNKNOWN;
mips_machtype = MACH_UNKNOWN;
break;
}
/* make sure we have the right initialization routine - sanity */
if (mips_machgroup != MACH_GROUP_MSP) {
ppfinit("Unknown machine group in a "
"MSP initialization routine\n");
panic("***Bogosity factor five***, exiting\n");
}
prom_init_cmdline();
prom_meminit();
/*
* Sub-system setup follows.
* Setup functions can either be called here or using the
* subsys_initcall mechanism (i.e. see msp_pci_setup). The
* order in which they are called can be changed by using the
* link order in arch/mips/pmc-sierra/msp71xx/Makefile.
*
* NOTE: Please keep sub-system specific initialization code
* in separate specific files.
*/
msp_serial_setup();
#ifdef CONFIG_PMCTWILED
/*
* Setup LED states before the subsys_initcall loads other
* dependant drivers/modules.
*/
pmctwiled_setup();
#endif
}

View File

@ -0,0 +1,94 @@
/*
* Setting up the clock on MSP SOCs. No RTC typically.
*
* Carsten Langgaard, carstenl@mips.com
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*/
#include <linux/init.h>
#include <linux/kernel_stat.h>
#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/module.h>
#include <linux/ptrace.h>
#include <asm/mipsregs.h>
#include <asm/time.h>
#include <msp_prom.h>
#include <msp_int.h>
#include <msp_regs.h>
void __init msp_timer_init(void)
{
char *endp, *s;
unsigned long cpu_rate = 0;
if (cpu_rate == 0) {
s = prom_getenv("clkfreqhz");
cpu_rate = simple_strtoul(s, &endp, 10);
if (endp != NULL && *endp != 0) {
printk(KERN_ERR
"Clock rate in Hz parse error: %s\n", s);
cpu_rate = 0;
}
}
if (cpu_rate == 0) {
s = prom_getenv("clkfreq");
cpu_rate = 1000 * simple_strtoul(s, &endp, 10);
if (endp != NULL && *endp != 0) {
printk(KERN_ERR
"Clock rate in MHz parse error: %s\n", s);
cpu_rate = 0;
}
}
if (cpu_rate == 0) {
#if defined(CONFIG_PMC_MSP7120_EVAL) \
|| defined(CONFIG_PMC_MSP7120_GW)
cpu_rate = 400000000;
#elif defined(CONFIG_PMC_MSP7120_FPGA)
cpu_rate = 25000000;
#else
cpu_rate = 150000000;
#endif
printk(KERN_ERR
"Failed to determine CPU clock rate, "
"assuming %ld hz ...\n", cpu_rate);
}
printk(KERN_WARNING "Clock rate set to %ld\n", cpu_rate);
/* timer frequency is 1/2 clock rate */
mips_hpt_frequency = cpu_rate/2;
}
void __init plat_timer_setup(struct irqaction *irq)
{
#ifdef CONFIG_IRQ_MSP_CIC
/* we are using the vpe0 counter for timer interrupts */
setup_irq(MSP_INT_VPE0_TIMER, irq);
#else
/* we are using the mips counter for timer interrupts */
setup_irq(MSP_INT_TIMER, irq);
#endif
}

View File

@ -0,0 +1,150 @@
/*
* The setup file for USB related hardware on PMC-Sierra MSP processors.
*
* Copyright 2006-2007 PMC-Sierra, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/dma-mapping.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/platform_device.h>
#include <asm/mipsregs.h>
#include <msp_regs.h>
#include <msp_int.h>
#include <msp_prom.h>
#if defined(CONFIG_USB_EHCI_HCD)
static struct resource msp_usbhost_resources [] = {
[0] = {
.start = MSP_USB_BASE_START,
.end = MSP_USB_BASE_END,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = MSP_INT_USB,
.end = MSP_INT_USB,
.flags = IORESOURCE_IRQ,
},
};
static u64 msp_usbhost_dma_mask = DMA_32BIT_MASK;
static struct platform_device msp_usbhost_device = {
.name = "pmcmsp-ehci",
.id = 0,
.dev = {
.dma_mask = &msp_usbhost_dma_mask,
.coherent_dma_mask = DMA_32BIT_MASK,
},
.num_resources = ARRAY_SIZE (msp_usbhost_resources),
.resource = msp_usbhost_resources,
};
#endif /* CONFIG_USB_EHCI_HCD */
#if defined(CONFIG_USB_GADGET)
static struct resource msp_usbdev_resources [] = {
[0] = {
.start = MSP_USB_BASE,
.end = MSP_USB_BASE_END,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = MSP_INT_USB,
.end = MSP_INT_USB,
.flags = IORESOURCE_IRQ,
},
};
static u64 msp_usbdev_dma_mask = DMA_32BIT_MASK;
static struct platform_device msp_usbdev_device = {
.name = "msp71xx_udc",
.id = 0,
.dev = {
.dma_mask = &msp_usbdev_dma_mask,
.coherent_dma_mask = DMA_32BIT_MASK,
},
.num_resources = ARRAY_SIZE (msp_usbdev_resources),
.resource = msp_usbdev_resources,
};
#endif /* CONFIG_USB_GADGET */
#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_GADGET)
static struct platform_device *msp_devs[1];
#endif
static int __init msp_usb_setup(void)
{
#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_GADGET)
char *strp;
char envstr[32];
unsigned int val = 0;
int result = 0;
/*
* construct environment name usbmode
* set usbmode <host/device> as pmon environment var
*/
snprintf((char *)&envstr[0], sizeof(envstr), "usbmode");
#if defined(CONFIG_USB_EHCI_HCD)
/* default to host mode */
val = 1;
#endif
/* get environment string */
strp = prom_getenv((char *)&envstr[0]);
if (strp) {
if (!strcmp(strp, "device"))
val = 0;
}
if (val) {
#if defined(CONFIG_USB_EHCI_HCD)
/* get host mode device */
msp_devs[0] = &msp_usbhost_device;
ppfinit("platform add USB HOST done %s.\n",
msp_devs[0]->name);
result = platform_add_devices(msp_devs, ARRAY_SIZE (msp_devs));
#endif /* CONFIG_USB_EHCI_HCD */
}
#if defined(CONFIG_USB_GADGET)
else {
/* get device mode structure */
msp_devs[0] = &msp_usbdev_device;
ppfinit("platform add USB DEVICE done %s.\n",
msp_devs[0]->name);
result = platform_add_devices(msp_devs, ARRAY_SIZE (msp_devs));
}
#endif /* CONFIG_USB_GADGET */
#endif /* CONFIG_USB_EHCI_HCD || CONFIG_USB_GADGET */
return result;
}
subsys_initcall(msp_usb_setup);

View File

@ -0,0 +1,151 @@
/*
* Defines for the MSP interrupt controller.
*
* Copyright (C) 1999 MIPS Technologies, Inc. All rights reserved.
* Author: Carsten Langgaard, carstenl@mips.com
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*/
#ifndef _MSP_CIC_INT_H
#define _MSP_CIC_INT_H
/*
* The PMC-Sierra CIC interrupts are all centrally managed by the
* CIC sub-system.
* We attempt to keep the interrupt numbers as consistent as possible
* across all of the MSP devices, but some differences will creep in ...
* The interrupts which are directly forwarded to the MIPS core interrupts
* are assigned interrupts in the range 0-7, interrupts cascaded through
* the CIC are assigned interrupts 8-39. The cascade occurs on C_IRQ4
* (MSP_INT_CIC). Currently we don't really distinguish between VPE1
* and VPE0 (or thread contexts for that matter). Will have to fix.
* The PER interrupts are assigned interrupts in the range 40-71.
*/
/*
* IRQs directly forwarded to the CPU
*/
#define MSP_MIPS_INTBASE 0
#define MSP_INT_SW0 0 /* IRQ for swint0, C_SW0 */
#define MSP_INT_SW1 1 /* IRQ for swint1, C_SW1 */
#define MSP_INT_MAC0 2 /* IRQ for MAC 0, C_IRQ0 */
#define MSP_INT_MAC1 3 /* IRQ for MAC 1, C_IRQ1 */
#define MSP_INT_USB 4 /* IRQ for USB, C_IRQ2 */
#define MSP_INT_SAR 5 /* IRQ for ADSL2+ SAR, C_IRQ3 */
#define MSP_INT_CIC 6 /* IRQ for CIC block, C_IRQ4 */
#define MSP_INT_SEC 7 /* IRQ for Sec engine, C_IRQ5 */
/*
* IRQs cascaded on CPU interrupt 4 (CAUSE bit 12, C_IRQ4)
* These defines should be tied to the register definitions for the CIC
* interrupt routine. For now, just use hard-coded values.
*/
#define MSP_CIC_INTBASE (MSP_MIPS_INTBASE + 8)
#define MSP_INT_EXT0 (MSP_CIC_INTBASE + 0)
/* External interrupt 0 */
#define MSP_INT_EXT1 (MSP_CIC_INTBASE + 1)
/* External interrupt 1 */
#define MSP_INT_EXT2 (MSP_CIC_INTBASE + 2)
/* External interrupt 2 */
#define MSP_INT_EXT3 (MSP_CIC_INTBASE + 3)
/* External interrupt 3 */
#define MSP_INT_CPUIF (MSP_CIC_INTBASE + 4)
/* CPU interface interrupt */
#define MSP_INT_EXT4 (MSP_CIC_INTBASE + 5)
/* External interrupt 4 */
#define MSP_INT_CIC_USB (MSP_CIC_INTBASE + 6)
/* Cascaded IRQ for USB */
#define MSP_INT_MBOX (MSP_CIC_INTBASE + 7)
/* Sec engine mailbox IRQ */
#define MSP_INT_EXT5 (MSP_CIC_INTBASE + 8)
/* External interrupt 5 */
#define MSP_INT_TDM (MSP_CIC_INTBASE + 9)
/* TDM interrupt */
#define MSP_INT_CIC_MAC0 (MSP_CIC_INTBASE + 10)
/* Cascaded IRQ for MAC 0 */
#define MSP_INT_CIC_MAC1 (MSP_CIC_INTBASE + 11)
/* Cascaded IRQ for MAC 1 */
#define MSP_INT_CIC_SEC (MSP_CIC_INTBASE + 12)
/* Cascaded IRQ for sec engine */
#define MSP_INT_PER (MSP_CIC_INTBASE + 13)
/* Peripheral interrupt */
#define MSP_INT_TIMER0 (MSP_CIC_INTBASE + 14)
/* SLP timer 0 */
#define MSP_INT_TIMER1 (MSP_CIC_INTBASE + 15)
/* SLP timer 1 */
#define MSP_INT_TIMER2 (MSP_CIC_INTBASE + 16)
/* SLP timer 2 */
#define MSP_INT_VPE0_TIMER (MSP_CIC_INTBASE + 17)
/* VPE0 MIPS timer */
#define MSP_INT_BLKCP (MSP_CIC_INTBASE + 18)
/* Block Copy */
#define MSP_INT_UART0 (MSP_CIC_INTBASE + 19)
/* UART 0 */
#define MSP_INT_PCI (MSP_CIC_INTBASE + 20)
/* PCI subsystem */
#define MSP_INT_EXT6 (MSP_CIC_INTBASE + 21)
/* External interrupt 5 */
#define MSP_INT_PCI_MSI (MSP_CIC_INTBASE + 22)
/* PCI Message Signal */
#define MSP_INT_CIC_SAR (MSP_CIC_INTBASE + 23)
/* Cascaded ADSL2+ SAR IRQ */
#define MSP_INT_DSL (MSP_CIC_INTBASE + 24)
/* ADSL2+ IRQ */
#define MSP_INT_CIC_ERR (MSP_CIC_INTBASE + 25)
/* SLP error condition */
#define MSP_INT_VPE1_TIMER (MSP_CIC_INTBASE + 26)
/* VPE1 MIPS timer */
#define MSP_INT_VPE0_PC (MSP_CIC_INTBASE + 27)
/* VPE0 Performance counter */
#define MSP_INT_VPE1_PC (MSP_CIC_INTBASE + 28)
/* VPE1 Performance counter */
#define MSP_INT_EXT7 (MSP_CIC_INTBASE + 29)
/* External interrupt 5 */
#define MSP_INT_VPE0_SW (MSP_CIC_INTBASE + 30)
/* VPE0 Software interrupt */
#define MSP_INT_VPE1_SW (MSP_CIC_INTBASE + 31)
/* VPE0 Software interrupt */
/*
* IRQs cascaded on CIC PER interrupt (MSP_INT_PER)
*/
#define MSP_PER_INTBASE (MSP_CIC_INTBASE + 32)
/* Reserved 0-1 */
#define MSP_INT_UART1 (MSP_PER_INTBASE + 2)
/* UART 1 */
/* Reserved 3-5 */
#define MSP_INT_2WIRE (MSP_PER_INTBASE + 6)
/* 2-wire */
#define MSP_INT_TM0 (MSP_PER_INTBASE + 7)
/* Peripheral timer block out 0 */
#define MSP_INT_TM1 (MSP_PER_INTBASE + 8)
/* Peripheral timer block out 1 */
/* Reserved 9 */
#define MSP_INT_SPRX (MSP_PER_INTBASE + 10)
/* SPI RX complete */
#define MSP_INT_SPTX (MSP_PER_INTBASE + 11)
/* SPI TX complete */
#define MSP_INT_GPIO (MSP_PER_INTBASE + 12)
/* GPIO */
#define MSP_INT_PER_ERR (MSP_PER_INTBASE + 13)
/* Peripheral error */
/* Reserved 14-31 */
#endif /* !_MSP_CIC_INT_H */

View File

@ -0,0 +1,43 @@
/*
* Defines for the MSP interrupt handlers.
*
* Copyright (C) 2005, PMC-Sierra, Inc. All rights reserved.
* Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*/
#ifndef _MSP_INT_H
#define _MSP_INT_H
/*
* The PMC-Sierra MSP product line has at least two different interrupt
* controllers, the SLP register based scheme and the CIC interrupt
* controller block mechanism. This file distinguishes between them
* so that devices see a uniform interface.
*/
#if defined(CONFIG_IRQ_MSP_SLP)
#include "msp_slp_int.h"
#elif defined(CONFIG_IRQ_MSP_CIC)
#include "msp_cic_int.h"
#else
#error "What sort of interrupt controller does *your* MSP have?"
#endif
#endif /* !_MSP_INT_H */

View File

@ -0,0 +1,176 @@
/*
* MIPS boards bootprom interface for the Linux kernel.
*
* Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
* Author: Carsten Langgaard, carstenl@mips.com
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*/
#ifndef _ASM_MSP_PROM_H
#define _ASM_MSP_PROM_H
#include <linux/types.h>
#define DEVICEID "deviceid"
#define FEATURES "features"
#define PROM_ENV "prom_env"
#define PROM_ENV_FILE "/proc/"PROM_ENV
#define PROM_ENV_SIZE 256
#define CPU_DEVID_FAMILY 0x0000ff00
#define CPU_DEVID_REVISION 0x000000ff
#define FPGA_IS_POLO(revision) \
(((revision >= 0xb0) && (revision < 0xd0)))
#define FPGA_IS_5000(revision) \
((revision >= 0x80) && (revision <= 0x90))
#define FPGA_IS_ZEUS(revision) ((revision < 0x7f))
#define FPGA_IS_DUET(revision) \
(((revision >= 0xa0) && (revision < 0xb0)))
#define FPGA_IS_MSP4200(revision) ((revision >= 0xd0))
#define FPGA_IS_MSP7100(revision) ((revision >= 0xd0))
#define MACHINE_TYPE_POLO "POLO"
#define MACHINE_TYPE_DUET "DUET"
#define MACHINE_TYPE_ZEUS "ZEUS"
#define MACHINE_TYPE_MSP2000REVB "MSP2000REVB"
#define MACHINE_TYPE_MSP5000 "MSP5000"
#define MACHINE_TYPE_MSP4200 "MSP4200"
#define MACHINE_TYPE_MSP7120 "MSP7120"
#define MACHINE_TYPE_MSP7130 "MSP7130"
#define MACHINE_TYPE_OTHER "OTHER"
#define MACHINE_TYPE_POLO_FPGA "POLO-FPGA"
#define MACHINE_TYPE_DUET_FPGA "DUET-FPGA"
#define MACHINE_TYPE_ZEUS_FPGA "ZEUS_FPGA"
#define MACHINE_TYPE_MSP2000REVB_FPGA "MSP2000REVB-FPGA"
#define MACHINE_TYPE_MSP5000_FPGA "MSP5000-FPGA"
#define MACHINE_TYPE_MSP4200_FPGA "MSP4200-FPGA"
#define MACHINE_TYPE_MSP7100_FPGA "MSP7100-FPGA"
#define MACHINE_TYPE_OTHER_FPGA "OTHER-FPGA"
/* Device Family definitions */
#define FAMILY_FPGA 0x0000
#define FAMILY_ZEUS 0x1000
#define FAMILY_POLO 0x2000
#define FAMILY_DUET 0x4000
#define FAMILY_TRIAD 0x5000
#define FAMILY_MSP4200 0x4200
#define FAMILY_MSP4200_FPGA 0x4f00
#define FAMILY_MSP7100 0x7100
#define FAMILY_MSP7100_FPGA 0x7f00
/* Device Type definitions */
#define TYPE_MSP7120 0x7120
#define TYPE_MSP7130 0x7130
#define ENET_KEY 'E'
#define ENETTXD_KEY 'e'
#define PCI_KEY 'P'
#define PCIMUX_KEY 'p'
#define SEC_KEY 'S'
#define SPAD_KEY 'D'
#define TDM_KEY 'T'
#define ZSP_KEY 'Z'
#define FEATURE_NOEXIST '-'
#define FEATURE_EXIST '+'
#define ENET_MII 'M'
#define ENET_RMII 'R'
#define ENETTXD_FALLING 'F'
#define ENETTXD_RISING 'R'
#define PCI_HOST 'H'
#define PCI_PERIPHERAL 'P'
#define PCIMUX_FULL 'F'
#define PCIMUX_SINGLE 'S'
#define SEC_DUET 'D'
#define SEC_POLO 'P'
#define SEC_SLOW 'S'
#define SEC_TRIAD 'T'
#define SPAD_POLO 'P'
#define TDM_DUET 'D' /* DUET TDMs might exist */
#define TDM_POLO 'P' /* POLO TDMs might exist */
#define TDM_TRIAD 'T' /* TRIAD TDMs might exist */
#define ZSP_DUET 'D' /* one DUET zsp engine */
#define ZSP_TRIAD 'T' /* two TRIAD zsp engines */
extern char *prom_getcmdline(void);
extern char *prom_getenv(char *name);
extern void prom_init_cmdline(void);
extern void prom_meminit(void);
extern void prom_fixup_mem_map(unsigned long start_mem,
unsigned long end_mem);
#ifdef CONFIG_MTD_PMC_MSP_RAMROOT
extern bool get_ramroot(void **start, unsigned long *size);
#endif
extern int get_ethernet_addr(char *ethaddr_name, char *ethernet_addr);
extern unsigned long get_deviceid(void);
extern char identify_enet(unsigned long interface_num);
extern char identify_enetTxD(unsigned long interface_num);
extern char identify_pci(void);
extern char identify_sec(void);
extern char identify_spad(void);
extern char identify_sec(void);
extern char identify_tdm(void);
extern char identify_zsp(void);
extern unsigned long identify_family(void);
extern unsigned long identify_revision(void);
/*
* The following macro calls prom_printf and puts the format string
* into an init section so it can be reclaimed.
*/
#define ppfinit(f, x...) \
do { \
static char _f[] __initdata = KERN_INFO f; \
printk(_f, ## x); \
} while (0)
/* Memory descriptor management. */
#define PROM_MAX_PMEMBLOCKS 7 /* 6 used */
enum yamon_memtypes {
yamon_dontuse,
yamon_prom,
yamon_free,
};
struct prom_pmemblock {
unsigned long base; /* Within KSEG0. */
unsigned int size; /* In bytes. */
unsigned int type; /* free or prom memory */
};
extern int prom_argc;
extern char **prom_argv;
extern char **prom_envp;
extern int *prom_vec;
extern struct prom_pmemblock *prom_getmdesc(void);
#endif /* !_ASM_MSP_PROM_H */

View File

@ -0,0 +1,236 @@
/*
* SMP/VPE-safe functions to access "registers" (see note).
*
* NOTES:
* - These macros use ll/sc instructions, so it is your responsibility to
* ensure these are available on your platform before including this file.
* - The MIPS32 spec states that ll/sc results are undefined for uncached
* accesses. This means they can't be used on HW registers accessed
* through kseg1. Code which requires these macros for this purpose must
* front-end the registers with cached memory "registers" and have a single
* thread update the actual HW registers.
* - A maximum of 2k of code can be inserted between ll and sc. Every
* memory accesses between the instructions will increase the chance of
* sc failing and having to loop.
* - When using custom_read_reg32/custom_write_reg32 only perform the
* necessary logical operations on the register value in between these
* two calls. All other logic should be performed before the first call.
* - There is a bug on the R10000 chips which has a workaround. If you
* are affected by this bug, make sure to define the symbol 'R10000_LLSC_WAR'
* to be non-zero. If you are using this header from within linux, you may
* include <asm/war.h> before including this file to have this defined
* appropriately for you.
*
* Copyright 2005-2007 PMC-Sierra, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
* EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc., 675
* Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef __ASM_REGOPS_H__
#define __ASM_REGOPS_H__
#include <linux/types.h>
#include <asm/war.h>
#ifndef R10000_LLSC_WAR
#define R10000_LLSC_WAR 0
#endif
#if R10000_LLSC_WAR == 1
#define __beqz "beqzl "
#else
#define __beqz "beqz "
#endif
#ifndef _LINUX_TYPES_H
typedef unsigned int u32;
#endif
/*
* Sets all the masked bits to the corresponding value bits
*/
static inline void set_value_reg32(volatile u32 *const addr,
u32 const mask,
u32 const value)
{
u32 temp;
__asm__ __volatile__(
" .set push \n"
" .set mips3 \n"
"1: ll %0, %1 # set_value_reg32 \n"
" and %0, %2 \n"
" or %0, %3 \n"
" sc %0, %1 \n"
" "__beqz"%0, 1b \n"
" nop \n"
" .set pop \n"
: "=&r" (temp), "=m" (*addr)
: "ir" (~mask), "ir" (value), "m" (*addr));
}
/*
* Sets all the masked bits to '1'
*/
static inline void set_reg32(volatile u32 *const addr,
u32 const mask)
{
u32 temp;
__asm__ __volatile__(
" .set push \n"
" .set mips3 \n"
"1: ll %0, %1 # set_reg32 \n"
" or %0, %2 \n"
" sc %0, %1 \n"
" "__beqz"%0, 1b \n"
" nop \n"
" .set pop \n"
: "=&r" (temp), "=m" (*addr)
: "ir" (mask), "m" (*addr));
}
/*
* Sets all the masked bits to '0'
*/
static inline void clear_reg32(volatile u32 *const addr,
u32 const mask)
{
u32 temp;
__asm__ __volatile__(
" .set push \n"
" .set mips3 \n"
"1: ll %0, %1 # clear_reg32 \n"
" and %0, %2 \n"
" sc %0, %1 \n"
" "__beqz"%0, 1b \n"
" nop \n"
" .set pop \n"
: "=&r" (temp), "=m" (*addr)
: "ir" (~mask), "m" (*addr));
}
/*
* Toggles all masked bits from '0' to '1' and '1' to '0'
*/
static inline void toggle_reg32(volatile u32 *const addr,
u32 const mask)
{
u32 temp;
__asm__ __volatile__(
" .set push \n"
" .set mips3 \n"
"1: ll %0, %1 # toggle_reg32 \n"
" xor %0, %2 \n"
" sc %0, %1 \n"
" "__beqz"%0, 1b \n"
" nop \n"
" .set pop \n"
: "=&r" (temp), "=m" (*addr)
: "ir" (mask), "m" (*addr));
}
/*
* Read all masked bits others are returned as '0'
*/
static inline u32 read_reg32(volatile u32 *const addr,
u32 const mask)
{
u32 temp;
__asm__ __volatile__(
" .set push \n"
" .set noreorder \n"
" lw %0, %1 # read \n"
" and %0, %2 # mask \n"
" .set pop \n"
: "=&r" (temp)
: "m" (*addr), "ir" (mask));
return temp;
}
/*
* blocking_read_reg32 - Read address with blocking load
*
* Uncached writes need to be read back to ensure they reach RAM.
* The returned value must be 'used' to prevent from becoming a
* non-blocking load.
*/
static inline u32 blocking_read_reg32(volatile u32 *const addr)
{
u32 temp;
__asm__ __volatile__(
" .set push \n"
" .set noreorder \n"
" lw %0, %1 # read \n"
" move %0, %0 # block \n"
" .set pop \n"
: "=&r" (temp)
: "m" (*addr));
return temp;
}
/*
* For special strange cases only:
*
* If you need custom processing within a ll/sc loop, use the following macros
* VERY CAREFULLY:
*
* u32 tmp; <-- Define a variable to hold the data
*
* custom_read_reg32(address, tmp); <-- Reads the address and put the value
* in the 'tmp' variable given
*
* From here on out, you are (basicly) atomic, so don't do anything too
* fancy!
* Also, this code may loop if the end of this block fails to write
* everything back safely due do the other CPU, so do NOT do anything
* with side-effects!
*
* custom_write_reg32(address, tmp); <-- Writes back 'tmp' safely.
*/
#define custom_read_reg32(address, tmp) \
__asm__ __volatile__( \
" .set push \n" \
" .set mips3 \n" \
"1: ll %0, %1 #custom_read_reg32 \n" \
" .set pop \n" \
: "=r" (tmp), "=m" (*address) \
: "m" (*address))
#define custom_write_reg32(address, tmp) \
__asm__ __volatile__( \
" .set push \n" \
" .set mips3 \n" \
" sc %0, %1 #custom_write_reg32 \n" \
" "__beqz"%0, 1b \n" \
" nop \n" \
" .set pop \n" \
: "=&r" (tmp), "=m" (*address) \
: "0" (tmp), "m" (*address))
#endif /* __ASM_REGOPS_H__ */

View File

@ -0,0 +1,667 @@
/*
* Defines for the address space, registers and register configuration
* (bit masks, access macros etc) for the PMC-Sierra line of MSP products.
* This file contains addess maps for all the devices in the line of
* products but only has register definitions and configuration masks for
* registers which aren't definitely associated with any device. Things
* like clock settings, reset access, the ELB etc. Individual device
* drivers will reference the appropriate XXX_BASE value defined here
* and have individual registers offset from that.
*
* Copyright (C) 2005-2007 PMC-Sierra, Inc. All rights reserved.
* Author: Andrew Hughes, Andrew_Hughes@pmc-sierra.com
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*/
#include <asm/addrspace.h>
#include <linux/types.h>
#ifndef _ASM_MSP_REGS_H
#define _ASM_MSP_REGS_H
/*
########################################################################
# Address space and device base definitions #
########################################################################
*/
/*
***************************************************************************
* System Logic and Peripherals (ELB, UART0, etc) device address space *
***************************************************************************
*/
#define MSP_SLP_BASE 0x1c000000
/* System Logic and Peripherals */
#define MSP_RST_BASE (MSP_SLP_BASE + 0x10)
/* System reset register base */
#define MSP_RST_SIZE 0x0C /* System reset register space */
#define MSP_WTIMER_BASE (MSP_SLP_BASE + 0x04C)
/* watchdog timer base */
#define MSP_ITIMER_BASE (MSP_SLP_BASE + 0x054)
/* internal timer base */
#define MSP_UART0_BASE (MSP_SLP_BASE + 0x100)
/* UART0 controller base */
#define MSP_BCPY_CTRL_BASE (MSP_SLP_BASE + 0x120)
/* Block Copy controller base */
#define MSP_BCPY_DESC_BASE (MSP_SLP_BASE + 0x160)
/* Block Copy descriptor base */
/*
***************************************************************************
* PCI address space *
***************************************************************************
*/
#define MSP_PCI_BASE 0x19000000
/*
***************************************************************************
* MSbus device address space *
***************************************************************************
*/
#define MSP_MSB_BASE 0x18000000
/* MSbus address start */
#define MSP_PER_BASE (MSP_MSB_BASE + 0x400000)
/* Peripheral device registers */
#define MSP_MAC0_BASE (MSP_MSB_BASE + 0x600000)
/* MAC A device registers */
#define MSP_MAC1_BASE (MSP_MSB_BASE + 0x700000)
/* MAC B device registers */
#define MSP_MAC_SIZE 0xE0 /* MAC register space */
#define MSP_SEC_BASE (MSP_MSB_BASE + 0x800000)
/* Security Engine registers */
#define MSP_MAC2_BASE (MSP_MSB_BASE + 0x900000)
/* MAC C device registers */
#define MSP_ADSL2_BASE (MSP_MSB_BASE + 0xA80000)
/* ADSL2 device registers */
#define MSP_USB_BASE (MSP_MSB_BASE + 0xB40000)
/* USB device registers */
#define MSP_USB_BASE_START (MSP_MSB_BASE + 0xB40100)
/* USB device registers */
#define MSP_USB_BASE_END (MSP_MSB_BASE + 0xB401FF)
/* USB device registers */
#define MSP_CPUIF_BASE (MSP_MSB_BASE + 0xC00000)
/* CPU interface registers */
/* Devices within the MSbus peripheral block */
#define MSP_UART1_BASE (MSP_PER_BASE + 0x030)
/* UART1 controller base */
#define MSP_SPI_BASE (MSP_PER_BASE + 0x058)
/* SPI/MPI control registers */
#define MSP_TWI_BASE (MSP_PER_BASE + 0x090)
/* Two-wire control registers */
#define MSP_PTIMER_BASE (MSP_PER_BASE + 0x0F0)
/* Programmable timer control */
/*
***************************************************************************
* Physical Memory configuration address space *
***************************************************************************
*/
#define MSP_MEM_CFG_BASE 0x17f00000
#define MSP_MEM_INDIRECT_CTL_10 0x10
/*
* Notes:
* 1) The SPI registers are split into two blocks, one offset from the
* MSP_SPI_BASE by 0x00 and the other offset from the MSP_SPI_BASE by
* 0x68. The SPI driver definitions for the register must be aware
* of this.
* 2) The block copy engine register are divided into two regions, one
* for the control/configuration of the engine proper and one for the
* values of the descriptors used in the copy process. These have
* different base defines (CTRL_BASE vs DESC_BASE)
* 3) These constants are for physical addresses which means that they
* work correctly with "ioremap" and friends. This means that device
* drivers will need to remap these addresses using ioremap and perhaps
* the readw/writew macros. Or they could use the regptr() macro
* defined below, but the readw/writew calls are the correct thing.
* 4) The UARTs have an additional status register offset from the base
* address. This register isn't used in the standard 8250 driver but
* may be used in other software. Consult the hardware datasheet for
* offset details.
* 5) For some unknown reason the security engine (MSP_SEC_BASE) registers
* start at an offset of 0x84 from the base address but the block of
* registers before this is reserved for the security engine. The
* driver will have to be aware of this but it makes the register
* definitions line up better with the documentation.
*/
/*
########################################################################
# System register definitions. Not associated with a specific device #
########################################################################
*/
/*
* This macro maps the physical register number into uncached space
* and (for C code) casts it into a u32 pointer so it can be dereferenced
* Normally these would be accessed with ioremap and readX/writeX, but
* these are convenient for a lot of internal kernel code.
*/
#ifdef __ASSEMBLER__
#define regptr(addr) (KSEG1ADDR(addr))
#else
#define regptr(addr) ((volatile u32 *const)(KSEG1ADDR(addr)))
#endif
/*
***************************************************************************
* System Logic and Peripherals (RESET, ELB, etc) registers *
***************************************************************************
*/
/* System Control register definitions */
#define DEV_ID_REG regptr(MSP_SLP_BASE + 0x00)
/* Device-ID RO */
#define FWR_ID_REG regptr(MSP_SLP_BASE + 0x04)
/* Firmware-ID Register RW */
#define SYS_ID_REG0 regptr(MSP_SLP_BASE + 0x08)
/* System-ID Register-0 RW */
#define SYS_ID_REG1 regptr(MSP_SLP_BASE + 0x0C)
/* System-ID Register-1 RW */
/* System Reset register definitions */
#define RST_STS_REG regptr(MSP_SLP_BASE + 0x10)
/* System Reset Status RO */
#define RST_SET_REG regptr(MSP_SLP_BASE + 0x14)
/* System Set Reset WO */
#define RST_CLR_REG regptr(MSP_SLP_BASE + 0x18)
/* System Clear Reset WO */
/* System Clock Registers */
#define PCI_SLP_REG regptr(MSP_SLP_BASE + 0x1C)
/* PCI clock generator RW */
#define URT_SLP_REG regptr(MSP_SLP_BASE + 0x20)
/* UART clock generator RW */
/* reserved (MSP_SLP_BASE + 0x24) */
/* reserved (MSP_SLP_BASE + 0x28) */
#define PLL1_SLP_REG regptr(MSP_SLP_BASE + 0x2C)
/* PLL1 clock generator RW */
#define PLL0_SLP_REG regptr(MSP_SLP_BASE + 0x30)
/* PLL0 clock generator RW */
#define MIPS_SLP_REG regptr(MSP_SLP_BASE + 0x34)
/* MIPS clock generator RW */
#define VE_SLP_REG regptr(MSP_SLP_BASE + 0x38)
/* Voice Eng clock generator RW */
/* reserved (MSP_SLP_BASE + 0x3C) */
#define MSB_SLP_REG regptr(MSP_SLP_BASE + 0x40)
/* MS-Bus clock generator RW */
#define SMAC_SLP_REG regptr(MSP_SLP_BASE + 0x44)
/* Sec & MAC clock generator RW */
#define PERF_SLP_REG regptr(MSP_SLP_BASE + 0x48)
/* Per & TDM clock generator RW */
/* Interrupt Controller Registers */
#define SLP_INT_STS_REG regptr(MSP_SLP_BASE + 0x70)
/* Interrupt status register RW */
#define SLP_INT_MSK_REG regptr(MSP_SLP_BASE + 0x74)
/* Interrupt enable/mask RW */
#define SE_MBOX_REG regptr(MSP_SLP_BASE + 0x78)
/* Security Engine mailbox RW */
#define VE_MBOX_REG regptr(MSP_SLP_BASE + 0x7C)
/* Voice Engine mailbox RW */
/* ELB Controller Registers */
#define CS0_CNFG_REG regptr(MSP_SLP_BASE + 0x80)
/* ELB CS0 Configuration Reg */
#define CS0_ADDR_REG regptr(MSP_SLP_BASE + 0x84)
/* ELB CS0 Base Address Reg */
#define CS0_MASK_REG regptr(MSP_SLP_BASE + 0x88)
/* ELB CS0 Mask Register */
#define CS0_ACCESS_REG regptr(MSP_SLP_BASE + 0x8C)
/* ELB CS0 access register */
#define CS1_CNFG_REG regptr(MSP_SLP_BASE + 0x90)
/* ELB CS1 Configuration Reg */
#define CS1_ADDR_REG regptr(MSP_SLP_BASE + 0x94)
/* ELB CS1 Base Address Reg */
#define CS1_MASK_REG regptr(MSP_SLP_BASE + 0x98)
/* ELB CS1 Mask Register */
#define CS1_ACCESS_REG regptr(MSP_SLP_BASE + 0x9C)
/* ELB CS1 access register */
#define CS2_CNFG_REG regptr(MSP_SLP_BASE + 0xA0)
/* ELB CS2 Configuration Reg */
#define CS2_ADDR_REG regptr(MSP_SLP_BASE + 0xA4)
/* ELB CS2 Base Address Reg */
#define CS2_MASK_REG regptr(MSP_SLP_BASE + 0xA8)
/* ELB CS2 Mask Register */
#define CS2_ACCESS_REG regptr(MSP_SLP_BASE + 0xAC)
/* ELB CS2 access register */
#define CS3_CNFG_REG regptr(MSP_SLP_BASE + 0xB0)
/* ELB CS3 Configuration Reg */
#define CS3_ADDR_REG regptr(MSP_SLP_BASE + 0xB4)
/* ELB CS3 Base Address Reg */
#define CS3_MASK_REG regptr(MSP_SLP_BASE + 0xB8)
/* ELB CS3 Mask Register */
#define CS3_ACCESS_REG regptr(MSP_SLP_BASE + 0xBC)
/* ELB CS3 access register */
#define CS4_CNFG_REG regptr(MSP_SLP_BASE + 0xC0)
/* ELB CS4 Configuration Reg */
#define CS4_ADDR_REG regptr(MSP_SLP_BASE + 0xC4)
/* ELB CS4 Base Address Reg */
#define CS4_MASK_REG regptr(MSP_SLP_BASE + 0xC8)
/* ELB CS4 Mask Register */
#define CS4_ACCESS_REG regptr(MSP_SLP_BASE + 0xCC)
/* ELB CS4 access register */
#define CS5_CNFG_REG regptr(MSP_SLP_BASE + 0xD0)
/* ELB CS5 Configuration Reg */
#define CS5_ADDR_REG regptr(MSP_SLP_BASE + 0xD4)
/* ELB CS5 Base Address Reg */
#define CS5_MASK_REG regptr(MSP_SLP_BASE + 0xD8)
/* ELB CS5 Mask Register */
#define CS5_ACCESS_REG regptr(MSP_SLP_BASE + 0xDC)
/* ELB CS5 access register */
/* reserved 0xE0 - 0xE8 */
#define ELB_1PC_EN_REG regptr(MSP_SLP_BASE + 0xEC)
/* ELB single PC card detect */
/* reserved 0xF0 - 0xF8 */
#define ELB_CLK_CFG_REG regptr(MSP_SLP_BASE + 0xFC)
/* SDRAM read/ELB timing Reg */
/* Extended UART status registers */
#define UART0_STATUS_REG regptr(MSP_UART0_BASE + 0x0c0)
/* UART Status Register 0 */
#define UART1_STATUS_REG regptr(MSP_UART1_BASE + 0x170)
/* UART Status Register 1 */
/* Performance monitoring registers */
#define PERF_MON_CTRL_REG regptr(MSP_SLP_BASE + 0x140)
/* Performance monitor control */
#define PERF_MON_CLR_REG regptr(MSP_SLP_BASE + 0x144)
/* Performance monitor clear */
#define PERF_MON_CNTH_REG regptr(MSP_SLP_BASE + 0x148)
/* Perf monitor counter high */
#define PERF_MON_CNTL_REG regptr(MSP_SLP_BASE + 0x14C)
/* Perf monitor counter low */
/* System control registers */
#define SYS_CTRL_REG regptr(MSP_SLP_BASE + 0x150)
/* System control register */
#define SYS_ERR1_REG regptr(MSP_SLP_BASE + 0x154)
/* System Error status 1 */
#define SYS_ERR2_REG regptr(MSP_SLP_BASE + 0x158)
/* System Error status 2 */
#define SYS_INT_CFG_REG regptr(MSP_SLP_BASE + 0x15C)
/* System Interrupt config */
/* Voice Engine Memory configuration */
#define VE_MEM_REG regptr(MSP_SLP_BASE + 0x17C)
/* Voice engine memory config */
/* CPU/SLP Error Status registers */
#define CPU_ERR1_REG regptr(MSP_SLP_BASE + 0x180)
/* CPU/SLP Error status 1 */
#define CPU_ERR2_REG regptr(MSP_SLP_BASE + 0x184)
/* CPU/SLP Error status 1 */
#define EXTENDED_GPIO_REG regptr(MSP_SLP_BASE + 0x188)
/* Extended GPIO register */
/* System Error registers */
#define SLP_ERR_STS_REG regptr(MSP_SLP_BASE + 0x190)
/* Int status for SLP errors */
#define SLP_ERR_MSK_REG regptr(MSP_SLP_BASE + 0x194)
/* Int mask for SLP errors */
#define SLP_ELB_ERST_REG regptr(MSP_SLP_BASE + 0x198)
/* External ELB reset */
#define SLP_BOOT_STS_REG regptr(MSP_SLP_BASE + 0x19C)
/* Boot Status */
/* Extended ELB addressing */
#define CS0_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1A0)
/* CS0 Extended address */
#define CS1_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1A4)
/* CS1 Extended address */
#define CS2_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1A8)
/* CS2 Extended address */
#define CS3_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1AC)
/* CS3 Extended address */
/* reserved 0x1B0 */
#define CS5_EXT_ADDR_REG regptr(MSP_SLP_BASE + 0x1B4)
/* CS5 Extended address */
/* PLL Adjustment registers */
#define PLL_LOCK_REG regptr(MSP_SLP_BASE + 0x200)
/* PLL0 lock status */
#define PLL_ARST_REG regptr(MSP_SLP_BASE + 0x204)
/* PLL Analog reset status */
#define PLL0_ADJ_REG regptr(MSP_SLP_BASE + 0x208)
/* PLL0 Adjustment value */
#define PLL1_ADJ_REG regptr(MSP_SLP_BASE + 0x20C)
/* PLL1 Adjustment value */
/*
***************************************************************************
* Peripheral Register definitions *
***************************************************************************
*/
/* Peripheral status */
#define PER_CTRL_REG regptr(MSP_PER_BASE + 0x50)
/* Peripheral control register */
#define PER_STS_REG regptr(MSP_PER_BASE + 0x54)
/* Peripheral status register */
/* SPI/MPI Registers */
#define SMPI_TX_SZ_REG regptr(MSP_PER_BASE + 0x58)
/* SPI/MPI Tx Size register */
#define SMPI_RX_SZ_REG regptr(MSP_PER_BASE + 0x5C)
/* SPI/MPI Rx Size register */
#define SMPI_CTL_REG regptr(MSP_PER_BASE + 0x60)
/* SPI/MPI Control register */
#define SMPI_MS_REG regptr(MSP_PER_BASE + 0x64)
/* SPI/MPI Chip Select reg */
#define SMPI_CORE_DATA_REG regptr(MSP_PER_BASE + 0xC0)
/* SPI/MPI Core Data reg */
#define SMPI_CORE_CTRL_REG regptr(MSP_PER_BASE + 0xC4)
/* SPI/MPI Core Control reg */
#define SMPI_CORE_STAT_REG regptr(MSP_PER_BASE + 0xC8)
/* SPI/MPI Core Status reg */
#define SMPI_CORE_SSEL_REG regptr(MSP_PER_BASE + 0xCC)
/* SPI/MPI Core Ssel reg */
#define SMPI_FIFO_REG regptr(MSP_PER_BASE + 0xD0)
/* SPI/MPI Data FIFO reg */
/* Peripheral Block Error Registers */
#define PER_ERR_STS_REG regptr(MSP_PER_BASE + 0x70)
/* Error Bit Status Register */
#define PER_ERR_MSK_REG regptr(MSP_PER_BASE + 0x74)
/* Error Bit Mask Register */
#define PER_HDR1_REG regptr(MSP_PER_BASE + 0x78)
/* Error Header 1 Register */
#define PER_HDR2_REG regptr(MSP_PER_BASE + 0x7C)
/* Error Header 2 Register */
/* Peripheral Block Interrupt Registers */
#define PER_INT_STS_REG regptr(MSP_PER_BASE + 0x80)
/* Interrupt status register */
#define PER_INT_MSK_REG regptr(MSP_PER_BASE + 0x84)
/* Interrupt Mask Register */
#define GPIO_INT_STS_REG regptr(MSP_PER_BASE + 0x88)
/* GPIO interrupt status reg */
#define GPIO_INT_MSK_REG regptr(MSP_PER_BASE + 0x8C)
/* GPIO interrupt MASK Reg */
/* POLO GPIO registers */
#define POLO_GPIO_DAT1_REG regptr(MSP_PER_BASE + 0x0E0)
/* Polo GPIO[8:0] data reg */
#define POLO_GPIO_CFG1_REG regptr(MSP_PER_BASE + 0x0E4)
/* Polo GPIO[7:0] config reg */
#define POLO_GPIO_CFG2_REG regptr(MSP_PER_BASE + 0x0E8)
/* Polo GPIO[15:8] config reg */
#define POLO_GPIO_OD1_REG regptr(MSP_PER_BASE + 0x0EC)
/* Polo GPIO[31:0] output drive */
#define POLO_GPIO_CFG3_REG regptr(MSP_PER_BASE + 0x170)
/* Polo GPIO[23:16] config reg */
#define POLO_GPIO_DAT2_REG regptr(MSP_PER_BASE + 0x174)
/* Polo GPIO[15:9] data reg */
#define POLO_GPIO_DAT3_REG regptr(MSP_PER_BASE + 0x178)
/* Polo GPIO[23:16] data reg */
#define POLO_GPIO_DAT4_REG regptr(MSP_PER_BASE + 0x17C)
/* Polo GPIO[31:24] data reg */
#define POLO_GPIO_DAT5_REG regptr(MSP_PER_BASE + 0x180)
/* Polo GPIO[39:32] data reg */
#define POLO_GPIO_DAT6_REG regptr(MSP_PER_BASE + 0x184)
/* Polo GPIO[47:40] data reg */
#define POLO_GPIO_DAT7_REG regptr(MSP_PER_BASE + 0x188)
/* Polo GPIO[54:48] data reg */
#define POLO_GPIO_CFG4_REG regptr(MSP_PER_BASE + 0x18C)
/* Polo GPIO[31:24] config reg */
#define POLO_GPIO_CFG5_REG regptr(MSP_PER_BASE + 0x190)
/* Polo GPIO[39:32] config reg */
#define POLO_GPIO_CFG6_REG regptr(MSP_PER_BASE + 0x194)
/* Polo GPIO[47:40] config reg */
#define POLO_GPIO_CFG7_REG regptr(MSP_PER_BASE + 0x198)
/* Polo GPIO[54:48] config reg */
#define POLO_GPIO_OD2_REG regptr(MSP_PER_BASE + 0x19C)
/* Polo GPIO[54:32] output drive */
/* Generic GPIO registers */
#define GPIO_DATA1_REG regptr(MSP_PER_BASE + 0x170)
/* GPIO[1:0] data register */
#define GPIO_DATA2_REG regptr(MSP_PER_BASE + 0x174)
/* GPIO[5:2] data register */
#define GPIO_DATA3_REG regptr(MSP_PER_BASE + 0x178)
/* GPIO[9:6] data register */
#define GPIO_DATA4_REG regptr(MSP_PER_BASE + 0x17C)
/* GPIO[15:10] data register */
#define GPIO_CFG1_REG regptr(MSP_PER_BASE + 0x180)
/* GPIO[1:0] config register */
#define GPIO_CFG2_REG regptr(MSP_PER_BASE + 0x184)
/* GPIO[5:2] config register */
#define GPIO_CFG3_REG regptr(MSP_PER_BASE + 0x188)
/* GPIO[9:6] config register */
#define GPIO_CFG4_REG regptr(MSP_PER_BASE + 0x18C)
/* GPIO[15:10] config register */
#define GPIO_OD_REG regptr(MSP_PER_BASE + 0x190)
/* GPIO[15:0] output drive */
/*
***************************************************************************
* CPU Interface register definitions *
***************************************************************************
*/
#define PCI_FLUSH_REG regptr(MSP_CPUIF_BASE + 0x00)
/* PCI-SDRAM queue flush trigger */
#define OCP_ERR1_REG regptr(MSP_CPUIF_BASE + 0x04)
/* OCP Error Attribute 1 */
#define OCP_ERR2_REG regptr(MSP_CPUIF_BASE + 0x08)
/* OCP Error Attribute 2 */
#define OCP_STS_REG regptr(MSP_CPUIF_BASE + 0x0C)
/* OCP Error Status */
#define CPUIF_PM_REG regptr(MSP_CPUIF_BASE + 0x10)
/* CPU policy configuration */
#define CPUIF_CFG_REG regptr(MSP_CPUIF_BASE + 0x10)
/* Misc configuration options */
/* Central Interrupt Controller Registers */
#define MSP_CIC_BASE (MSP_CPUIF_BASE + 0x8000)
/* Central Interrupt registers */
#define CIC_EXT_CFG_REG regptr(MSP_CIC_BASE + 0x00)
/* External interrupt config */
#define CIC_STS_REG regptr(MSP_CIC_BASE + 0x04)
/* CIC Interrupt Status */
#define CIC_VPE0_MSK_REG regptr(MSP_CIC_BASE + 0x08)
/* VPE0 Interrupt Mask */
#define CIC_VPE1_MSK_REG regptr(MSP_CIC_BASE + 0x0C)
/* VPE1 Interrupt Mask */
#define CIC_TC0_MSK_REG regptr(MSP_CIC_BASE + 0x10)
/* Thread Context 0 Int Mask */
#define CIC_TC1_MSK_REG regptr(MSP_CIC_BASE + 0x14)
/* Thread Context 1 Int Mask */
#define CIC_TC2_MSK_REG regptr(MSP_CIC_BASE + 0x18)
/* Thread Context 2 Int Mask */
#define CIC_TC3_MSK_REG regptr(MSP_CIC_BASE + 0x18)
/* Thread Context 3 Int Mask */
#define CIC_TC4_MSK_REG regptr(MSP_CIC_BASE + 0x18)
/* Thread Context 4 Int Mask */
#define CIC_PCIMSI_STS_REG regptr(MSP_CIC_BASE + 0x18)
#define CIC_PCIMSI_MSK_REG regptr(MSP_CIC_BASE + 0x18)
#define CIC_PCIFLSH_REG regptr(MSP_CIC_BASE + 0x18)
#define CIC_VPE0_SWINT_REG regptr(MSP_CIC_BASE + 0x08)
/*
***************************************************************************
* Memory controller registers *
***************************************************************************
*/
#define MEM_CFG1_REG regptr(MSP_MEM_CFG_BASE + 0x00)
#define MEM_SS_ADDR regptr(MSP_MEM_CFG_BASE + 0x00)
#define MEM_SS_DATA regptr(MSP_MEM_CFG_BASE + 0x04)
#define MEM_SS_WRITE regptr(MSP_MEM_CFG_BASE + 0x08)
/*
***************************************************************************
* PCI controller registers *
***************************************************************************
*/
#define PCI_BASE_REG regptr(MSP_PCI_BASE + 0x00)
#define PCI_CONFIG_SPACE_REG regptr(MSP_PCI_BASE + 0x800)
#define PCI_JTAG_DEVID_REG regptr(MSP_SLP_BASE + 0x13c)
/*
########################################################################
# Register content & macro definitions #
########################################################################
*/
/*
***************************************************************************
* DEV_ID defines *
***************************************************************************
*/
#define DEV_ID_PCI_DIS (1 << 26) /* Set if PCI disabled */
#define DEV_ID_PCI_HOST (1 << 20) /* Set if PCI host */
#define DEV_ID_SINGLE_PC (1 << 19) /* Set if single PC Card */
#define DEV_ID_FAMILY (0xff << 8) /* family ID code */
#define POLO_ZEUS_SUB_FAMILY (0x7 << 16) /* sub family for Polo/Zeus */
#define MSPFPGA_ID (0x00 << 8) /* you are on your own here */
#define MSP5000_ID (0x50 << 8)
#define MSP4F00_ID (0x4f << 8) /* FPGA version of MSP4200 */
#define MSP4E00_ID (0x4f << 8) /* FPGA version of MSP7120 */
#define MSP4200_ID (0x42 << 8)
#define MSP4000_ID (0x40 << 8)
#define MSP2XXX_ID (0x20 << 8)
#define MSPZEUS_ID (0x10 << 8)
#define MSP2004_SUB_ID (0x0 << 16)
#define MSP2005_SUB_ID (0x1 << 16)
#define MSP2006_SUB_ID (0x1 << 16)
#define MSP2007_SUB_ID (0x2 << 16)
#define MSP2010_SUB_ID (0x3 << 16)
#define MSP2015_SUB_ID (0x4 << 16)
#define MSP2020_SUB_ID (0x5 << 16)
#define MSP2100_SUB_ID (0x6 << 16)
/*
***************************************************************************
* RESET defines *
***************************************************************************
*/
#define MSP_GR_RST (0x01 << 0) /* Global reset bit */
#define MSP_MR_RST (0x01 << 1) /* MIPS reset bit */
#define MSP_PD_RST (0x01 << 2) /* PVC DMA reset bit */
#define MSP_PP_RST (0x01 << 3) /* PVC reset bit */
/* reserved */
#define MSP_EA_RST (0x01 << 6) /* Mac A reset bit */
#define MSP_EB_RST (0x01 << 7) /* Mac B reset bit */
#define MSP_SE_RST (0x01 << 8) /* Security Eng reset bit */
#define MSP_PB_RST (0x01 << 9) /* Per block reset bit */
#define MSP_EC_RST (0x01 << 10) /* Mac C reset bit */
#define MSP_TW_RST (0x01 << 11) /* TWI reset bit */
#define MSP_SPI_RST (0x01 << 12) /* SPI/MPI reset bit */
#define MSP_U1_RST (0x01 << 13) /* UART1 reset bit */
#define MSP_U0_RST (0x01 << 14) /* UART0 reset bit */
/*
***************************************************************************
* UART defines *
***************************************************************************
*/
#ifndef CONFIG_MSP_FPGA
#define MSP_BASE_BAUD 25000000
#else
#define MSP_BASE_BAUD 6000000
#endif
#define MSP_UART_REG_LEN 0x20
/*
***************************************************************************
* ELB defines *
***************************************************************************
*/
#define PCCARD_32 0x02 /* Set if is PCCARD 32 (Cardbus) */
#define SINGLE_PCCARD 0x01 /* Set to enable single PC card */
/*
***************************************************************************
* CIC defines *
***************************************************************************
*/
/* CIC_EXT_CFG_REG */
#define EXT_INT_POL(eirq) (1 << (eirq + 8))
#define EXT_INT_EDGE(eirq) (1 << eirq)
#define CIC_EXT_SET_TRIGGER_LEVEL(reg, eirq) (reg &= ~EXT_INT_EDGE(eirq))
#define CIC_EXT_SET_TRIGGER_EDGE(reg, eirq) (reg |= EXT_INT_EDGE(eirq))
#define CIC_EXT_SET_ACTIVE_HI(reg, eirq) (reg |= EXT_INT_POL(eirq))
#define CIC_EXT_SET_ACTIVE_LO(reg, eirq) (reg &= ~EXT_INT_POL(eirq))
#define CIC_EXT_SET_ACTIVE_RISING CIC_EXT_SET_ACTIVE_HI
#define CIC_EXT_SET_ACTIVE_FALLING CIC_EXT_SET_ACTIVE_LO
#define CIC_EXT_IS_TRIGGER_LEVEL(reg, eirq) \
((reg & EXT_INT_EDGE(eirq)) == 0)
#define CIC_EXT_IS_TRIGGER_EDGE(reg, eirq) (reg & EXT_INT_EDGE(eirq))
#define CIC_EXT_IS_ACTIVE_HI(reg, eirq) (reg & EXT_INT_POL(eirq))
#define CIC_EXT_IS_ACTIVE_LO(reg, eirq) \
((reg & EXT_INT_POL(eirq)) == 0)
#define CIC_EXT_IS_ACTIVE_RISING CIC_EXT_IS_ACTIVE_HI
#define CIC_EXT_IS_ACTIVE_FALLING CIC_EXT_IS_ACTIVE_LO
/*
***************************************************************************
* Memory Controller defines *
***************************************************************************
*/
/* Indirect memory controller registers */
#define DDRC_CFG(n) (n)
#define DDRC_DEBUG(n) (0x04 + n)
#define DDRC_CTL(n) (0x40 + n)
/* Macro to perform DDRC indirect write */
#define DDRC_INDIRECT_WRITE(reg, mask, value) \
({ \
*MEM_SS_ADDR = (((mask) & 0xf) << 8) | ((reg) & 0xff); \
*MEM_SS_DATA = (value); \
*MEM_SS_WRITE = 1; \
})
/*
***************************************************************************
* SPI/MPI Mode *
***************************************************************************
*/
#define SPI_MPI_RX_BUSY 0x00008000 /* SPI/MPI Receive Busy */
#define SPI_MPI_FIFO_EMPTY 0x00004000 /* SPI/MPI Fifo Empty */
#define SPI_MPI_TX_BUSY 0x00002000 /* SPI/MPI Transmit Busy */
#define SPI_MPI_FIFO_FULL 0x00001000 /* SPI/MPU FIFO full */
/*
***************************************************************************
* SPI/MPI Control Register *
***************************************************************************
*/
#define SPI_MPI_RX_START 0x00000004 /* Start receive command */
#define SPI_MPI_FLUSH_Q 0x00000002 /* Flush SPI/MPI Queue */
#define SPI_MPI_TX_START 0x00000001 /* Start Transmit Command */
#endif /* !_ASM_MSP_REGS_H */

View File

@ -0,0 +1,141 @@
/*
* Defines for the MSP interrupt controller.
*
* Copyright (C) 1999 MIPS Technologies, Inc. All rights reserved.
* Author: Carsten Langgaard, carstenl@mips.com
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*/
#ifndef _MSP_SLP_INT_H
#define _MSP_SLP_INT_H
/*
* The PMC-Sierra SLP interrupts are arranged in a 3 level cascaded
* hierarchical system. The first level are the direct MIPS interrupts
* and are assigned the interrupt range 0-7. The second level is the SLM
* interrupt controller and is assigned the range 8-39. The third level
* comprises the Peripherial block, the PCI block, the PCI MSI block and
* the SLP. The PCI interrupts and the SLP errors are handled by the
* relevant subsystems so the core interrupt code needs only concern
* itself with the Peripheral block. These are assigned interrupts in
* the range 40-71.
*/
/*
* IRQs directly connected to CPU
*/
#define MSP_MIPS_INTBASE 0
#define MSP_INT_SW0 0 /* IRQ for swint0, C_SW0 */
#define MSP_INT_SW1 1 /* IRQ for swint1, C_SW1 */
#define MSP_INT_MAC0 2 /* IRQ for MAC 0, C_IRQ0 */
#define MSP_INT_MAC1 3 /* IRQ for MAC 1, C_IRQ1 */
#define MSP_INT_C_IRQ2 4 /* Wired off, C_IRQ2 */
#define MSP_INT_VE 5 /* IRQ for Voice Engine, C_IRQ3 */
#define MSP_INT_SLP 6 /* IRQ for SLM block, C_IRQ4 */
#define MSP_INT_TIMER 7 /* IRQ for the MIPS timer, C_IRQ5 */
/*
* IRQs cascaded on CPU interrupt 4 (CAUSE bit 12, C_IRQ4)
* These defines should be tied to the register definition for the SLM
* interrupt routine. For now, just use hard-coded values.
*/
#define MSP_SLP_INTBASE (MSP_MIPS_INTBASE + 8)
#define MSP_INT_EXT0 (MSP_SLP_INTBASE + 0)
/* External interrupt 0 */
#define MSP_INT_EXT1 (MSP_SLP_INTBASE + 1)
/* External interrupt 1 */
#define MSP_INT_EXT2 (MSP_SLP_INTBASE + 2)
/* External interrupt 2 */
#define MSP_INT_EXT3 (MSP_SLP_INTBASE + 3)
/* External interrupt 3 */
/* Reserved 4-7 */
/*
*************************************************************************
* DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER/DANGER *
* Some MSP produces have this interrupt labelled as Voice and some are *
* SEC mbox ... *
*************************************************************************
*/
#define MSP_INT_SLP_VE (MSP_SLP_INTBASE + 8)
/* Cascaded IRQ for Voice Engine*/
#define MSP_INT_SLP_TDM (MSP_SLP_INTBASE + 9)
/* TDM interrupt */
#define MSP_INT_SLP_MAC0 (MSP_SLP_INTBASE + 10)
/* Cascaded IRQ for MAC 0 */
#define MSP_INT_SLP_MAC1 (MSP_SLP_INTBASE + 11)
/* Cascaded IRQ for MAC 1 */
#define MSP_INT_SEC (MSP_SLP_INTBASE + 12)
/* IRQ for security engine */
#define MSP_INT_PER (MSP_SLP_INTBASE + 13)
/* Peripheral interrupt */
#define MSP_INT_TIMER0 (MSP_SLP_INTBASE + 14)
/* SLP timer 0 */
#define MSP_INT_TIMER1 (MSP_SLP_INTBASE + 15)
/* SLP timer 1 */
#define MSP_INT_TIMER2 (MSP_SLP_INTBASE + 16)
/* SLP timer 2 */
#define MSP_INT_SLP_TIMER (MSP_SLP_INTBASE + 17)
/* Cascaded MIPS timer */
#define MSP_INT_BLKCP (MSP_SLP_INTBASE + 18)
/* Block Copy */
#define MSP_INT_UART0 (MSP_SLP_INTBASE + 19)
/* UART 0 */
#define MSP_INT_PCI (MSP_SLP_INTBASE + 20)
/* PCI subsystem */
#define MSP_INT_PCI_DBELL (MSP_SLP_INTBASE + 21)
/* PCI doorbell */
#define MSP_INT_PCI_MSI (MSP_SLP_INTBASE + 22)
/* PCI Message Signal */
#define MSP_INT_PCI_BC0 (MSP_SLP_INTBASE + 23)
/* PCI Block Copy 0 */
#define MSP_INT_PCI_BC1 (MSP_SLP_INTBASE + 24)
/* PCI Block Copy 1 */
#define MSP_INT_SLP_ERR (MSP_SLP_INTBASE + 25)
/* SLP error condition */
#define MSP_INT_MAC2 (MSP_SLP_INTBASE + 26)
/* IRQ for MAC2 */
/* Reserved 26-31 */
/*
* IRQs cascaded on SLP PER interrupt (MSP_INT_PER)
*/
#define MSP_PER_INTBASE (MSP_SLP_INTBASE + 32)
/* Reserved 0-1 */
#define MSP_INT_UART1 (MSP_PER_INTBASE + 2)
/* UART 1 */
/* Reserved 3-5 */
#define MSP_INT_2WIRE (MSP_PER_INTBASE + 6)
/* 2-wire */
#define MSP_INT_TM0 (MSP_PER_INTBASE + 7)
/* Peripheral timer block out 0 */
#define MSP_INT_TM1 (MSP_PER_INTBASE + 8)
/* Peripheral timer block out 1 */
/* Reserved 9 */
#define MSP_INT_SPRX (MSP_PER_INTBASE + 10)
/* SPI RX complete */
#define MSP_INT_SPTX (MSP_PER_INTBASE + 11)
/* SPI TX complete */
#define MSP_INT_GPIO (MSP_PER_INTBASE + 12)
/* GPIO */
#define MSP_INT_PER_ERR (MSP_PER_INTBASE + 13)
/* Peripheral error */
/* Reserved 14-31 */
#endif /* !_MSP_SLP_INT_H */