dt/bindings: remove device_type "network" references

device_type is deprecated and the kernel doesn't require it in most
cases. The only exceptions for flat tree users are the "gianfar",
"ucc_geth" and "ibm,emac" bindings, and arguably that requirement could
be relaxed for ucc_geth and ibm,emac (that is a task for separate
patches though).

This patch removes references to device_type="network" from the binding
documentation where possible and removes the properties from ARM and
microblaze dts files. This patch does not modify the powerpc .dts files
since there are a much larger number of them affected and I think the
ucc_geth, ibm,emac and gianfar users should be addressed before clearing
out the references to reduce the chance of breakage.

Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
This commit is contained in:
Grant Likely 2013-12-11 10:37:37 +00:00
parent dae95c1f07
commit 351291754d
7 changed files with 0 additions and 10 deletions

View File

@ -130,7 +130,6 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
Ethernet port node
Required properties:
- device_type : Should be "network".
- compatible : Should be "marvell,mv64360-eth".
- reg : Should be <0>, <1>, or <2>, according to which registers
within the silicon block the device uses.
@ -143,7 +142,6 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd.
Example Discovery Ethernet port node:
ethernet@0 {
device_type = "network";
compatible = "marvell,mv64360-eth";
reg = <0>;
interrupts = <32>;

View File

@ -32,7 +32,6 @@ Optional controller properties:
* Ethernet port node
Required port properties:
- device_type: shall be "network".
- compatible: shall be one of "marvell,orion-eth-port",
"marvell,kirkwood-eth-port".
- reg: port number relative to ethernet controller, shall be 0, 1, or 2.
@ -74,7 +73,6 @@ eth: ethernet-controller@72000 {
marvell,tx-checksum-limit = <1600>;
ethernet@0 {
device_type = "network";
compatible = "marvell,orion-eth-port";
reg = <0>;
interrupts = <29>;

View File

@ -10,7 +10,6 @@ Currently defined compatibles:
Example:
ethernet@11300 {
device_type = "network";
compatible = "fsl,mpc8272-fcc-enet",
"fsl,cpm2-fcc-enet";
reg = <11300 20 8400 100 11390 1>;

View File

@ -573,7 +573,6 @@
status = "disabled";
ethernet-port@0 {
device_type = "network";
compatible = "marvell,orion-eth-port";
reg = <0>;
interrupts = <29>;

View File

@ -253,7 +253,6 @@
status = "disabled";
ethernet0-port@0 {
device_type = "network";
compatible = "marvell,kirkwood-eth-port";
reg = <0>;
interrupts = <11>;
@ -273,7 +272,6 @@
status = "disabled";
ethernet1-port@0 {
device_type = "network";
compatible = "marvell,kirkwood-eth-port";
reg = <0>;
interrupts = <15>;

View File

@ -154,7 +154,6 @@
status = "disabled";
ethernet-port@0 {
device_type = "network";
compatible = "marvell,orion-eth-port";
reg = <0>;
/* overwrite MAC address in bootloader */

View File

@ -222,7 +222,6 @@
ranges ;
ethernet@81c00000 {
compatible = "xlnx,xps-ll-temac-1.01.b", "xlnx,xps-ll-temac-1.00.a";
device_type = "network";
interrupt-parent = <&xps_intc_0>;
interrupts = < 5 2 >;
llink-connected = <&PIM3>;