mirror of
https://github.com/torvalds/linux.git
synced 2024-11-12 07:01:57 +00:00
[PATCH] I2C: W83792D documentation 3/3
This patch adds documentation entry for W83792D chip. Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit is contained in:
R.Marek@sh.cvut.cz
Greg Kroah-Hartman
parent
ce785ab460
commit
1ff4e3065b
174
Documentation/hwmon/w83792d
Normal file
174
Documentation/hwmon/w83792d
Normal file
@ -0,0 +1,174 @@
|
||||
Kernel driver w83792d
|
||||
=====================
|
||||
|
||||
Supported chips:
|
||||
* Winbond W83792D
|
||||
Prefix: 'w83792d'
|
||||
Addresses scanned: I2C 0x2c - 0x2f
|
||||
Datasheet: http://www.winbond.com.tw/E-WINBONDHTM/partner/PDFresult.asp?Pname=1035
|
||||
|
||||
Author: Chunhao Huang
|
||||
Contact: DZShen <DZShen@Winbond.com.tw>
|
||||
|
||||
|
||||
Module Parameters
|
||||
-----------------
|
||||
|
||||
* init int
|
||||
(default 1)
|
||||
Use 'init=0' to bypass initializing the chip.
|
||||
Try this if your computer crashes when you load the module.
|
||||
|
||||
* force_subclients=bus,caddr,saddr,saddr
|
||||
This is used to force the i2c addresses for subclients of
|
||||
a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'
|
||||
to force the subclients of chip 0x2f on bus 0 to i2c addresses
|
||||
0x4a and 0x4b.
|
||||
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
This driver implements support for the Winbond W83792AD/D.
|
||||
|
||||
Detection of the chip can sometimes be foiled because it can be in an
|
||||
internal state that allows no clean access (Bank with ID register is not
|
||||
currently selected). If you know the address of the chip, use a 'force'
|
||||
parameter; this will put it into a more well-behaved state first.
|
||||
|
||||
The driver implements three temperature sensors, seven fan rotation speed
|
||||
sensors, nine voltage sensors, and two automatic fan regulation
|
||||
strategies called: Smart Fan I (Thermal Cruise mode) and Smart Fan II.
|
||||
Automatic fan control mode is possible only for fan1-fan3. Fan4-fan7 can run
|
||||
synchronized with selected fan (fan1-fan3). This functionality and manual PWM
|
||||
control for fan4-fan7 is not yet implemented.
|
||||
|
||||
Temperatures are measured in degrees Celsius and measurement resolution is 1
|
||||
degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
|
||||
the temperature gets higher than the Overtemperature Shutdown value; it stays
|
||||
on until the temperature falls below the Hysteresis value.
|
||||
|
||||
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
|
||||
triggered if the rotation speed has dropped below a programmable limit. Fan
|
||||
readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or
|
||||
128) to give the readings more range or accuracy.
|
||||
|
||||
Voltage sensors (also known as IN sensors) report their values in millivolts.
|
||||
An alarm is triggered if the voltage has crossed a programmable minimum
|
||||
or maximum limit.
|
||||
|
||||
Alarms are provided as output from "realtime status register". Following bits
|
||||
are defined:
|
||||
|
||||
bit - alarm on:
|
||||
0 - in0
|
||||
1 - in1
|
||||
2 - temp1
|
||||
3 - temp2
|
||||
4 - temp3
|
||||
5 - fan1
|
||||
6 - fan2
|
||||
7 - fan3
|
||||
8 - in2
|
||||
9 - in3
|
||||
10 - in4
|
||||
11 - in5
|
||||
12 - in6
|
||||
13 - VID change
|
||||
14 - chassis
|
||||
15 - fan7
|
||||
16 - tart1
|
||||
17 - tart2
|
||||
18 - tart3
|
||||
19 - in7
|
||||
20 - in8
|
||||
21 - fan4
|
||||
22 - fan5
|
||||
23 - fan6
|
||||
|
||||
Tart will be asserted while target temperature cannot be achieved after 3 minutes
|
||||
of full speed rotation of corresponding fan.
|
||||
|
||||
In addition to the alarms described above, there is a CHAS alarm on the chips
|
||||
which triggers if your computer case is open (This one is latched, contrary
|
||||
to realtime alarms).
|
||||
|
||||
The chips only update values each 3 seconds; reading them more often will
|
||||
do no harm, but will return 'old' values.
|
||||
|
||||
|
||||
W83792D PROBLEMS
|
||||
----------------
|
||||
Known problems:
|
||||
- This driver is only for Winbond W83792D C version device, there
|
||||
are also some motherboards with B version W83792D device. The
|
||||
calculation method to in6-in7(measured value, limits) is a little
|
||||
different between C and B version. C or B version can be identified
|
||||
by CR[0x49h].
|
||||
- The function of vid and vrm has not been finished, because I'm NOT
|
||||
very familiar with them. Adding support is welcome.
|
||||
- The function of chassis open detection needs more tests.
|
||||
- If you have ASUS server board and chip was not found: Then you will
|
||||
need to upgrade to latest (or beta) BIOS. If it does not help please
|
||||
contact us.
|
||||
|
||||
Fan control
|
||||
-----------
|
||||
|
||||
Manual mode
|
||||
-----------
|
||||
|
||||
Works as expected. You just need to specify desired PWM/DC value (fan speed)
|
||||
in appropriate pwm# file.
|
||||
|
||||
Thermal cruise
|
||||
--------------
|
||||
|
||||
In this mode, W83792D provides the Smart Fan system to automatically control
|
||||
fan speed to keep the temperatures of CPU and the system within specific
|
||||
range. At first a wanted temperature and interval must be set. This is done
|
||||
via thermal_cruise# file. The tolerance# file serves to create T +- tolerance
|
||||
interval. The fan speed will be lowered as long as the current temperature
|
||||
remains below the thermal_cruise# +- tolerance# value. Once the temperature
|
||||
exceeds the high limit (T+tolerance), the fan will be turned on with a
|
||||
specific speed set by pwm# and automatically controlled its PWM duty cycle
|
||||
with the temperature varying. Three conditions may occur:
|
||||
|
||||
(1) If the temperature still exceeds the high limit, PWM duty
|
||||
cycle will increase slowly.
|
||||
|
||||
(2) If the temperature goes below the high limit, but still above the low
|
||||
limit (T-tolerance), the fan speed will be fixed at the current speed because
|
||||
the temperature is in the target range.
|
||||
|
||||
(3) If the temperature goes below the low limit, PWM duty cycle will decrease
|
||||
slowly to 0 or a preset stop value until the temperature exceeds the low
|
||||
limit. (The preset stop value handling is not yet implemented in driver)
|
||||
|
||||
Smart Fan II
|
||||
------------
|
||||
|
||||
W83792D also provides a special mode for fan. Four temperature points are
|
||||
available. When related temperature sensors detects the temperature in preset
|
||||
temperature region (sf2_point@_fan# +- tolerance#) it will cause fans to run
|
||||
on programmed value from sf2_level@_fan#. You need to set four temperatures
|
||||
for each fan.
|
||||
|
||||
|
||||
/sys files
|
||||
----------
|
||||
|
||||
pwm[1-3] - this file stores PWM duty cycle or DC value (fan speed) in range:
|
||||
0 (stop) to 255 (full)
|
||||
pwm[1-3]_enable - this file controls mode of fan/temperature control:
|
||||
* 0 Disabled
|
||||
* 1 Manual mode
|
||||
* 2 Smart Fan II
|
||||
* 3 Thermal Cruise
|
||||
pwm[1-3]_mode - Select PWM of DC mode
|
||||
* 0 DC
|
||||
* 1 PWM
|
||||
thermal_cruise[1-3] - Selects the desired temperature for cruise (degC)
|
||||
tolerance[1-3] - Value in degrees of Celsius (degC) for +- T
|
||||
sf2_point[1-4]_fan[1-3] - four temperature points for each fan for Smart Fan II
|
||||
sf2_level[1-3]_fan[1-3] - three PWM/DC levels for each fan for Smart Fan II
|
||||
Loading…
Reference in New Issue
Block a user