linux/net/sched/Makefile

53 lines
1.9 KiB
Makefile
Raw Normal View History

#
# Makefile for the Linux Traffic Control Unit.
#
obj-y := sch_generic.o sch_mq.o
obj-$(CONFIG_NET_SCHED) += sch_api.o sch_blackhole.o
obj-$(CONFIG_NET_CLS) += cls_api.o
obj-$(CONFIG_NET_CLS_ACT) += act_api.o
obj-$(CONFIG_NET_ACT_POLICE) += act_police.o
obj-$(CONFIG_NET_ACT_GACT) += act_gact.o
obj-$(CONFIG_NET_ACT_MIRRED) += act_mirred.o
obj-$(CONFIG_NET_ACT_IPT) += act_ipt.o
[PKT_SCHED]: Add stateless NAT Stateless NAT is useful in controlled environments where restrictions are placed on through traffic such that we don't need connection tracking to correctly NAT protocol-specific data. In particular, this is of interest when the number of flows or the number of addresses being NATed is large, or if connection tracking information has to be replicated and where it is not practical to do so. Previously we had stateless NAT functionality which was integrated into the IPv4 routing subsystem. This was a great solution as long as the NAT worked on a subnet to subnet basis such that the number of NAT rules was relatively small. The reason is that for SNAT the routing based system had to perform a linear scan through the rules. If the number of rules is large then major renovations would have take place in the routing subsystem to make this practical. For the time being, the least intrusive way of achieving this is to use the u32 classifier written by Alexey Kuznetsov along with the actions infrastructure implemented by Jamal Hadi Salim. The following patch is an attempt at this problem by creating a new nat action that can be invoked from u32 hash tables which would allow large number of stateless NAT rules that can be used/updated in constant time. The actual NAT code is mostly based on the previous stateless NAT code written by Alexey. In future we might be able to utilise the protocol NAT code from netfilter to improve support for other protocols. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-09-27 19:48:05 +00:00
obj-$(CONFIG_NET_ACT_NAT) += act_nat.o
obj-$(CONFIG_NET_ACT_PEDIT) += act_pedit.o
obj-$(CONFIG_NET_ACT_SIMP) += act_simple.o
obj-$(CONFIG_NET_ACT_SKBEDIT) += act_skbedit.o
obj-$(CONFIG_NET_ACT_CSUM) += act_csum.o
obj-$(CONFIG_NET_SCH_FIFO) += sch_fifo.o
obj-$(CONFIG_NET_SCH_CBQ) += sch_cbq.o
obj-$(CONFIG_NET_SCH_HTB) += sch_htb.o
obj-$(CONFIG_NET_SCH_HFSC) += sch_hfsc.o
obj-$(CONFIG_NET_SCH_RED) += sch_red.o
obj-$(CONFIG_NET_SCH_GRED) += sch_gred.o
obj-$(CONFIG_NET_SCH_INGRESS) += sch_ingress.o
obj-$(CONFIG_NET_SCH_DSMARK) += sch_dsmark.o
obj-$(CONFIG_NET_SCH_SFQ) += sch_sfq.o
obj-$(CONFIG_NET_SCH_TBF) += sch_tbf.o
obj-$(CONFIG_NET_SCH_TEQL) += sch_teql.o
obj-$(CONFIG_NET_SCH_PRIO) += sch_prio.o
obj-$(CONFIG_NET_SCH_MULTIQ) += sch_multiq.o
obj-$(CONFIG_NET_SCH_ATM) += sch_atm.o
obj-$(CONFIG_NET_SCH_NETEM) += sch_netem.o
obj-$(CONFIG_NET_SCH_DRR) += sch_drr.o
net_sched: implement a root container qdisc sch_mqprio This implements a mqprio queueing discipline that by default creates a pfifo_fast qdisc per tx queue and provides the needed configuration interface. Using the mqprio qdisc the number of tcs currently in use along with the range of queues alloted to each class can be configured. By default skbs are mapped to traffic classes using the skb priority. This mapping is configurable. Configurable parameters, struct tc_mqprio_qopt { __u8 num_tc; __u8 prio_tc_map[TC_BITMASK + 1]; __u8 hw; __u16 count[TC_MAX_QUEUE]; __u16 offset[TC_MAX_QUEUE]; }; Here the count/offset pairing give the queue alignment and the prio_tc_map gives the mapping from skb->priority to tc. The hw bit determines if the hardware should configure the count and offset values. If the hardware bit is set then the operation will fail if the hardware does not implement the ndo_setup_tc operation. This is to avoid undetermined states where the hardware may or may not control the queue mapping. Also minimal bounds checking is done on the count/offset to verify a queue does not exceed num_tx_queues and that queue ranges do not overlap. Otherwise it is left to user policy or hardware configuration to create useful mappings. It is expected that hardware QOS schemes can be implemented by creating appropriate mappings of queues in ndo_tc_setup(). One expected use case is drivers will use the ndo_setup_tc to map queue ranges onto 802.1Q traffic classes. This provides a generic mechanism to map network traffic onto these traffic classes and removes the need for lower layer drivers to know specifics about traffic types. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-17 08:06:09 +00:00
obj-$(CONFIG_NET_SCH_MQPRIO) += sch_mqprio.o
obj-$(CONFIG_NET_SCH_CHOKE) += sch_choke.o
obj-$(CONFIG_NET_CLS_U32) += cls_u32.o
obj-$(CONFIG_NET_CLS_ROUTE4) += cls_route.o
obj-$(CONFIG_NET_CLS_FW) += cls_fw.o
obj-$(CONFIG_NET_CLS_RSVP) += cls_rsvp.o
obj-$(CONFIG_NET_CLS_TCINDEX) += cls_tcindex.o
obj-$(CONFIG_NET_CLS_RSVP6) += cls_rsvp6.o
obj-$(CONFIG_NET_CLS_BASIC) += cls_basic.o
obj-$(CONFIG_NET_CLS_FLOW) += cls_flow.o
obj-$(CONFIG_NET_CLS_CGROUP) += cls_cgroup.o
obj-$(CONFIG_NET_EMATCH) += ematch.o
obj-$(CONFIG_NET_EMATCH_CMP) += em_cmp.o
obj-$(CONFIG_NET_EMATCH_NBYTE) += em_nbyte.o
obj-$(CONFIG_NET_EMATCH_U32) += em_u32.o
obj-$(CONFIG_NET_EMATCH_META) += em_meta.o
obj-$(CONFIG_NET_EMATCH_TEXT) += em_text.o