linux/kernel/irq/internals.h

341 lines
9.8 KiB
C
Raw Normal View History

/*
* IRQ subsystem internal functions and variables:
*
* Do not ever include this file from anything else than
* kernel/irq/. Do not even think about using any information outside
* of this file for your non core code.
*/
#include <linux/irqdesc.h>
#include <linux/kernel_stat.h>
#include <linux/pm_runtime.h>
genirq: Prevent access beyond allocated_irqs bitmap Lars-Peter Clausen pointed out: I stumbled upon this while looking through the existing archs using SPARSE_IRQ. Even with SPARSE_IRQ the NR_IRQS is still the upper limit for the number of IRQs. Both PXA and MMP set NR_IRQS to IRQ_BOARD_START, with IRQ_BOARD_START being the number of IRQs used by the core. In various machine files the nr_irqs field of the ARM machine defintion struct is then set to "IRQ_BOARD_START + NR_BOARD_IRQS". As a result "nr_irqs" will greater then NR_IRQS which then again causes the "allocated_irqs" bitmap in the core irq code to be accessed beyond its size overwriting unrelated data. The core code really misses a sanity check there. This went unnoticed so far as by chance the compiler/linker places data behind that bitmap which gets initialized later on those affected platforms. So the obvious fix would be to add a sanity check in early_irq_init() and break all affected platforms. Though that check wants to be backported to stable as well, which will require to fix all known problematic platforms and probably some more yet not known ones as well. Lots of churn. A way simpler solution is to allocate a slightly larger bitmap and avoid the whole churn w/o breaking anything. Add a few warnings when an arch returns utter crap. Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org # .37 Cc: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org>
2011-02-17 16:45:15 +00:00
#ifdef CONFIG_SPARSE_IRQ
# define IRQ_BITMAP_BITS (NR_IRQS + 8196)
#else
# define IRQ_BITMAP_BITS NR_IRQS
#endif
#define istate core_internal_state__do_not_mess_with_it
extern bool noirqdebug;
genirq: Allow migration of chained interrupts by installing default action When a CPU is offlined all interrupts that have an action are migrated to other still online CPUs. However, if the interrupt has chained handler installed this is not done. Chained handlers are used by GPIO drivers which support interrupts, for instance. When the affinity is not corrected properly we end up in situation where most interrupts are not arriving to the online CPUs anymore. For example on Intel Braswell system which has SD-card card detection signal connected to a GPIO the IO-APIC routing entries look like below after CPU1 is offlined: pin30, enabled , level, low , V(52), IRR(0), S(0), logical , D(03), M(1) pin31, enabled , level, low , V(42), IRR(0), S(0), logical , D(03), M(1) pin32, enabled , level, low , V(62), IRR(0), S(0), logical , D(03), M(1) pin5b, enabled , level, low , V(72), IRR(0), S(0), logical , D(03), M(1) The problem here is that the destination mask still contains both CPUs even if CPU1 is already offline. This means that the IO-APIC still routes interrupts to the other CPU as well. We solve the problem by providing a default action for chained interrupts. This action allows the migration code to correct affinity (as it finds desc->action != NULL). Also make the default action handler to emit a warning if for some reason a chained handler ends up calling it. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Link: http://lkml.kernel.org/r/1444039935-30475-1-git-send-email-mika.westerberg@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-10-05 10:12:15 +00:00
extern struct irqaction chained_action;
/*
* Bits used by threaded handlers:
* IRQTF_RUNTHREAD - signals that the interrupt handler thread should run
* IRQTF_WARNED - warning "IRQ_WAKE_THREAD w/o thread_fn" has been printed
* IRQTF_AFFINITY - irq thread is requested to adjust affinity
genirq: Provide forced interrupt threading Add a commandline parameter "threadirqs" which forces all interrupts except those marked IRQF_NO_THREAD to run threaded. That's mostly a debug option to allow retrieving better debug data from crashing interrupt handlers. If "threadirqs" is not enabled on the kernel command line, then there is no impact in the interrupt hotpath. Architecture code needs to select CONFIG_IRQ_FORCED_THREADING after marking the interrupts which cant be threaded IRQF_NO_THREAD. All interrupts which have IRQF_TIMER set are implict marked IRQF_NO_THREAD. Also all PER_CPU interrupts are excluded. Forced threading hard interrupts also forces all soft interrupt handling into thread context. When enabled it might slow down things a bit, but for debugging problems in interrupt code it's a reasonable penalty as it does not immediately crash and burn the machine when an interrupt handler is buggy. Some test results on a Core2Duo machine: Cache cold run of: # time git grep irq_desc non-threaded threaded real 1m18.741s 1m19.061s user 0m1.874s 0m1.757s sys 0m5.843s 0m5.427s # iperf -c server non-threaded [ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec threaded [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 937 Mbits/sec Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> LKML-Reference: <20110223234956.772668648@linutronix.de>
2011-02-23 23:52:23 +00:00
* IRQTF_FORCED_THREAD - irq action is force threaded
*/
enum {
IRQTF_RUNTHREAD,
IRQTF_WARNED,
IRQTF_AFFINITY,
genirq: Provide forced interrupt threading Add a commandline parameter "threadirqs" which forces all interrupts except those marked IRQF_NO_THREAD to run threaded. That's mostly a debug option to allow retrieving better debug data from crashing interrupt handlers. If "threadirqs" is not enabled on the kernel command line, then there is no impact in the interrupt hotpath. Architecture code needs to select CONFIG_IRQ_FORCED_THREADING after marking the interrupts which cant be threaded IRQF_NO_THREAD. All interrupts which have IRQF_TIMER set are implict marked IRQF_NO_THREAD. Also all PER_CPU interrupts are excluded. Forced threading hard interrupts also forces all soft interrupt handling into thread context. When enabled it might slow down things a bit, but for debugging problems in interrupt code it's a reasonable penalty as it does not immediately crash and burn the machine when an interrupt handler is buggy. Some test results on a Core2Duo machine: Cache cold run of: # time git grep irq_desc non-threaded threaded real 1m18.741s 1m19.061s user 0m1.874s 0m1.757s sys 0m5.843s 0m5.427s # iperf -c server non-threaded [ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec threaded [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec [ 3] 0.0-10.0 sec 1.09 GBytes 937 Mbits/sec Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> LKML-Reference: <20110223234956.772668648@linutronix.de>
2011-02-23 23:52:23 +00:00
IRQTF_FORCED_THREAD,
};
/*
* Bit masks for desc->core_internal_state__do_not_mess_with_it
*
* IRQS_AUTODETECT - autodetection in progress
* IRQS_SPURIOUS_DISABLED - was disabled due to spurious interrupt
* detection
* IRQS_POLL_INPROGRESS - polling in progress
* IRQS_ONESHOT - irq is not unmasked in primary handler
* IRQS_REPLAY - irq is replayed
* IRQS_WAITING - irq is waiting
* IRQS_PENDING - irq is pending and replayed later
* IRQS_SUSPENDED - irq is suspended
*/
enum {
IRQS_AUTODETECT = 0x00000001,
IRQS_SPURIOUS_DISABLED = 0x00000002,
IRQS_POLL_INPROGRESS = 0x00000008,
IRQS_ONESHOT = 0x00000020,
IRQS_REPLAY = 0x00000040,
IRQS_WAITING = 0x00000080,
IRQS_PENDING = 0x00000200,
IRQS_SUSPENDED = 0x00000800,
};
#include "debug.h"
#include "settings.h"
extern int __irq_set_trigger(struct irq_desc *desc, unsigned long flags);
extern void __disable_irq(struct irq_desc *desc);
extern void __enable_irq(struct irq_desc *desc);
#define IRQ_RESEND true
#define IRQ_NORESEND false
#define IRQ_START_FORCE true
#define IRQ_START_COND false
extern int irq_startup(struct irq_desc *desc, bool resend, bool force);
extern void irq_shutdown(struct irq_desc *desc);
extern void irq_enable(struct irq_desc *desc);
extern void irq_disable(struct irq_desc *desc);
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
extern void irq_percpu_enable(struct irq_desc *desc, unsigned int cpu);
extern void irq_percpu_disable(struct irq_desc *desc, unsigned int cpu);
extern void mask_irq(struct irq_desc *desc);
extern void unmask_irq(struct irq_desc *desc);
extern void unmask_threaded_irq(struct irq_desc *desc);
#ifdef CONFIG_SPARSE_IRQ
static inline void irq_mark_irq(unsigned int irq) { }
#else
extern void irq_mark_irq(unsigned int irq);
#endif
extern void init_kstat_irqs(struct irq_desc *desc, int node, int nr);
irqreturn_t __handle_irq_event_percpu(struct irq_desc *desc, unsigned int *flags);
irqreturn_t handle_irq_event_percpu(struct irq_desc *desc);
irqreturn_t handle_irq_event(struct irq_desc *desc);
/* Resending of interrupts :*/
void check_irq_resend(struct irq_desc *desc);
bool irq_wait_for_poll(struct irq_desc *desc);
void __irq_wake_thread(struct irq_desc *desc, struct irqaction *action);
#ifdef CONFIG_PROC_FS
extern void register_irq_proc(unsigned int irq, struct irq_desc *desc);
extern void unregister_irq_proc(unsigned int irq, struct irq_desc *desc);
extern void register_handler_proc(unsigned int irq, struct irqaction *action);
extern void unregister_handler_proc(unsigned int irq, struct irqaction *action);
#else
static inline void register_irq_proc(unsigned int irq, struct irq_desc *desc) { }
static inline void unregister_irq_proc(unsigned int irq, struct irq_desc *desc) { }
static inline void register_handler_proc(unsigned int irq,
struct irqaction *action) { }
static inline void unregister_handler_proc(unsigned int irq,
struct irqaction *action) { }
#endif
extern bool irq_can_set_affinity_usr(unsigned int irq);
extern int irq_select_affinity_usr(unsigned int irq);
extern void irq_set_thread_affinity(struct irq_desc *desc);
extern int irq_do_set_affinity(struct irq_data *data,
const struct cpumask *dest, bool force);
#ifdef CONFIG_SMP
extern int irq_setup_affinity(struct irq_desc *desc);
#else
static inline int irq_setup_affinity(struct irq_desc *desc) { return 0; }
#endif
genirq: Add buslock support Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The bus access needs to sleep and therefor cannot be called in atomic contexts. Some of the generic interrupt management functions like disable_irq(), enable_irq() ... call interrupt chip functions with the irq_desc->lock held and interrupts disabled. This does not work for such devices. Provide a separate synchronization mechanism for such interrupt chips. The irq_chip structure is extended by two optional functions (bus_lock and bus_sync_and_unlock). The idea is to serialize the bus access for those operations in the core code so that drivers which are behind that bus operated interrupt controller do not have to worry about it and just can use the normal interfaces. To achieve this we add two function pointers to the irq_chip: bus_lock and bus_sync_unlock. bus_lock() is called to serialize access to the interrupt controller bus. Now the core code can issue chip->mask/unmask ... commands without changing the fast path code at all. The chip implementation merily stores that information in a chip private data structure and returns. No bus interaction as these functions are called from atomic context. After that bus_sync_unlock() is called outside the atomic context. Now the chip implementation issues the bus commands, waits for completion and unlocks the interrupt controller bus. The irq_chip implementation as pseudo code: struct irq_chip_data { struct mutex mutex; unsigned int irq_offset; unsigned long mask; unsigned long mask_status; } static void bus_lock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); mutex_lock(&data->mutex); } static void mask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask |= (1 << irq); } static void unmask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask &= ~(1 << irq); } static void bus_sync_unlock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); if (data->mask != data->mask_status) { do_bus_magic_to_set_mask(data->mask); data->mask_status = data->mask; } mutex_unlock(&data->mutex); } The device drivers can use request_threaded_irq, free_irq, disable_irq and enable_irq as usual with the only restriction that the calls need to come from non atomic context. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Trilok Soni <soni.trilok@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Brian Swetland <swetland@google.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: m.szyprowski@samsung.com Cc: t.fujak@samsung.com Cc: kyungmin.park@samsung.com, Cc: David Brownell <david-b@pacbell.net> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: arve@android.com Cc: Barry Song <21cnbao@gmail.com>
2009-08-13 10:17:48 +00:00
/* Inline functions for support of irq chips on slow busses */
static inline void chip_bus_lock(struct irq_desc *desc)
genirq: Add buslock support Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The bus access needs to sleep and therefor cannot be called in atomic contexts. Some of the generic interrupt management functions like disable_irq(), enable_irq() ... call interrupt chip functions with the irq_desc->lock held and interrupts disabled. This does not work for such devices. Provide a separate synchronization mechanism for such interrupt chips. The irq_chip structure is extended by two optional functions (bus_lock and bus_sync_and_unlock). The idea is to serialize the bus access for those operations in the core code so that drivers which are behind that bus operated interrupt controller do not have to worry about it and just can use the normal interfaces. To achieve this we add two function pointers to the irq_chip: bus_lock and bus_sync_unlock. bus_lock() is called to serialize access to the interrupt controller bus. Now the core code can issue chip->mask/unmask ... commands without changing the fast path code at all. The chip implementation merily stores that information in a chip private data structure and returns. No bus interaction as these functions are called from atomic context. After that bus_sync_unlock() is called outside the atomic context. Now the chip implementation issues the bus commands, waits for completion and unlocks the interrupt controller bus. The irq_chip implementation as pseudo code: struct irq_chip_data { struct mutex mutex; unsigned int irq_offset; unsigned long mask; unsigned long mask_status; } static void bus_lock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); mutex_lock(&data->mutex); } static void mask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask |= (1 << irq); } static void unmask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask &= ~(1 << irq); } static void bus_sync_unlock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); if (data->mask != data->mask_status) { do_bus_magic_to_set_mask(data->mask); data->mask_status = data->mask; } mutex_unlock(&data->mutex); } The device drivers can use request_threaded_irq, free_irq, disable_irq and enable_irq as usual with the only restriction that the calls need to come from non atomic context. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Trilok Soni <soni.trilok@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Brian Swetland <swetland@google.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: m.szyprowski@samsung.com Cc: t.fujak@samsung.com Cc: kyungmin.park@samsung.com, Cc: David Brownell <david-b@pacbell.net> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: arve@android.com Cc: Barry Song <21cnbao@gmail.com>
2009-08-13 10:17:48 +00:00
{
if (unlikely(desc->irq_data.chip->irq_bus_lock))
desc->irq_data.chip->irq_bus_lock(&desc->irq_data);
genirq: Add buslock support Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The bus access needs to sleep and therefor cannot be called in atomic contexts. Some of the generic interrupt management functions like disable_irq(), enable_irq() ... call interrupt chip functions with the irq_desc->lock held and interrupts disabled. This does not work for such devices. Provide a separate synchronization mechanism for such interrupt chips. The irq_chip structure is extended by two optional functions (bus_lock and bus_sync_and_unlock). The idea is to serialize the bus access for those operations in the core code so that drivers which are behind that bus operated interrupt controller do not have to worry about it and just can use the normal interfaces. To achieve this we add two function pointers to the irq_chip: bus_lock and bus_sync_unlock. bus_lock() is called to serialize access to the interrupt controller bus. Now the core code can issue chip->mask/unmask ... commands without changing the fast path code at all. The chip implementation merily stores that information in a chip private data structure and returns. No bus interaction as these functions are called from atomic context. After that bus_sync_unlock() is called outside the atomic context. Now the chip implementation issues the bus commands, waits for completion and unlocks the interrupt controller bus. The irq_chip implementation as pseudo code: struct irq_chip_data { struct mutex mutex; unsigned int irq_offset; unsigned long mask; unsigned long mask_status; } static void bus_lock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); mutex_lock(&data->mutex); } static void mask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask |= (1 << irq); } static void unmask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask &= ~(1 << irq); } static void bus_sync_unlock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); if (data->mask != data->mask_status) { do_bus_magic_to_set_mask(data->mask); data->mask_status = data->mask; } mutex_unlock(&data->mutex); } The device drivers can use request_threaded_irq, free_irq, disable_irq and enable_irq as usual with the only restriction that the calls need to come from non atomic context. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Trilok Soni <soni.trilok@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Brian Swetland <swetland@google.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: m.szyprowski@samsung.com Cc: t.fujak@samsung.com Cc: kyungmin.park@samsung.com, Cc: David Brownell <david-b@pacbell.net> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: arve@android.com Cc: Barry Song <21cnbao@gmail.com>
2009-08-13 10:17:48 +00:00
}
static inline void chip_bus_sync_unlock(struct irq_desc *desc)
genirq: Add buslock support Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The bus access needs to sleep and therefor cannot be called in atomic contexts. Some of the generic interrupt management functions like disable_irq(), enable_irq() ... call interrupt chip functions with the irq_desc->lock held and interrupts disabled. This does not work for such devices. Provide a separate synchronization mechanism for such interrupt chips. The irq_chip structure is extended by two optional functions (bus_lock and bus_sync_and_unlock). The idea is to serialize the bus access for those operations in the core code so that drivers which are behind that bus operated interrupt controller do not have to worry about it and just can use the normal interfaces. To achieve this we add two function pointers to the irq_chip: bus_lock and bus_sync_unlock. bus_lock() is called to serialize access to the interrupt controller bus. Now the core code can issue chip->mask/unmask ... commands without changing the fast path code at all. The chip implementation merily stores that information in a chip private data structure and returns. No bus interaction as these functions are called from atomic context. After that bus_sync_unlock() is called outside the atomic context. Now the chip implementation issues the bus commands, waits for completion and unlocks the interrupt controller bus. The irq_chip implementation as pseudo code: struct irq_chip_data { struct mutex mutex; unsigned int irq_offset; unsigned long mask; unsigned long mask_status; } static void bus_lock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); mutex_lock(&data->mutex); } static void mask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask |= (1 << irq); } static void unmask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask &= ~(1 << irq); } static void bus_sync_unlock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); if (data->mask != data->mask_status) { do_bus_magic_to_set_mask(data->mask); data->mask_status = data->mask; } mutex_unlock(&data->mutex); } The device drivers can use request_threaded_irq, free_irq, disable_irq and enable_irq as usual with the only restriction that the calls need to come from non atomic context. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Trilok Soni <soni.trilok@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Brian Swetland <swetland@google.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: m.szyprowski@samsung.com Cc: t.fujak@samsung.com Cc: kyungmin.park@samsung.com, Cc: David Brownell <david-b@pacbell.net> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: arve@android.com Cc: Barry Song <21cnbao@gmail.com>
2009-08-13 10:17:48 +00:00
{
if (unlikely(desc->irq_data.chip->irq_bus_sync_unlock))
desc->irq_data.chip->irq_bus_sync_unlock(&desc->irq_data);
genirq: Add buslock support Some interrupt chips are connected to a "slow" bus (i2c, spi ...). The bus access needs to sleep and therefor cannot be called in atomic contexts. Some of the generic interrupt management functions like disable_irq(), enable_irq() ... call interrupt chip functions with the irq_desc->lock held and interrupts disabled. This does not work for such devices. Provide a separate synchronization mechanism for such interrupt chips. The irq_chip structure is extended by two optional functions (bus_lock and bus_sync_and_unlock). The idea is to serialize the bus access for those operations in the core code so that drivers which are behind that bus operated interrupt controller do not have to worry about it and just can use the normal interfaces. To achieve this we add two function pointers to the irq_chip: bus_lock and bus_sync_unlock. bus_lock() is called to serialize access to the interrupt controller bus. Now the core code can issue chip->mask/unmask ... commands without changing the fast path code at all. The chip implementation merily stores that information in a chip private data structure and returns. No bus interaction as these functions are called from atomic context. After that bus_sync_unlock() is called outside the atomic context. Now the chip implementation issues the bus commands, waits for completion and unlocks the interrupt controller bus. The irq_chip implementation as pseudo code: struct irq_chip_data { struct mutex mutex; unsigned int irq_offset; unsigned long mask; unsigned long mask_status; } static void bus_lock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); mutex_lock(&data->mutex); } static void mask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask |= (1 << irq); } static void unmask(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); irq -= data->irq_offset; data->mask &= ~(1 << irq); } static void bus_sync_unlock(unsigned int irq) { struct irq_chip_data *data = get_irq_desc_chip_data(irq); if (data->mask != data->mask_status) { do_bus_magic_to_set_mask(data->mask); data->mask_status = data->mask; } mutex_unlock(&data->mutex); } The device drivers can use request_threaded_irq, free_irq, disable_irq and enable_irq as usual with the only restriction that the calls need to come from non atomic context. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Trilok Soni <soni.trilok@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Brian Swetland <swetland@google.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: m.szyprowski@samsung.com Cc: t.fujak@samsung.com Cc: kyungmin.park@samsung.com, Cc: David Brownell <david-b@pacbell.net> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: arve@android.com Cc: Barry Song <21cnbao@gmail.com>
2009-08-13 10:17:48 +00:00
}
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
#define _IRQ_DESC_CHECK (1 << 0)
#define _IRQ_DESC_PERCPU (1 << 1)
#define IRQ_GET_DESC_CHECK_GLOBAL (_IRQ_DESC_CHECK)
#define IRQ_GET_DESC_CHECK_PERCPU (_IRQ_DESC_CHECK | _IRQ_DESC_PERCPU)
#define for_each_action_of_desc(desc, act) \
for (act = desc->act; act; act = act->next)
struct irq_desc *
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
__irq_get_desc_lock(unsigned int irq, unsigned long *flags, bool bus,
unsigned int check);
void __irq_put_desc_unlock(struct irq_desc *desc, unsigned long flags, bool bus);
static inline struct irq_desc *
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
irq_get_desc_buslock(unsigned int irq, unsigned long *flags, unsigned int check)
{
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
return __irq_get_desc_lock(irq, flags, true, check);
}
static inline void
irq_put_desc_busunlock(struct irq_desc *desc, unsigned long flags)
{
__irq_put_desc_unlock(desc, flags, true);
}
static inline struct irq_desc *
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
irq_get_desc_lock(unsigned int irq, unsigned long *flags, unsigned int check)
{
genirq: Add support for per-cpu dev_id interrupts The ARM GIC interrupt controller offers per CPU interrupts (PPIs), which are usually used to connect local timers to each core. Each CPU has its own private interface to the GIC, and only sees the PPIs that are directly connect to it. While these timers are separate devices and have a separate interrupt line to a core, they all use the same IRQ number. For these devices, request_irq() is not the right API as it assumes that an IRQ number is visible by a number of CPUs (through the affinity setting), but makes it very awkward to express that an IRQ number can be handled by all CPUs, and yet be a different interrupt line on each CPU, requiring a different dev_id cookie to be passed back to the handler. The *_percpu_irq() functions is designed to overcome these limitations, by providing a per-cpu dev_id vector: int request_percpu_irq(unsigned int irq, irq_handler_t handler, const char *devname, void __percpu *percpu_dev_id); void free_percpu_irq(unsigned int, void __percpu *); int setup_percpu_irq(unsigned int irq, struct irqaction *new); void remove_percpu_irq(unsigned int irq, struct irqaction *act); void enable_percpu_irq(unsigned int irq); void disable_percpu_irq(unsigned int irq); The API has a number of limitations: - no interrupt sharing - no threading - common handler across all the CPUs Once the interrupt is requested using setup_percpu_irq() or request_percpu_irq(), it must be enabled by each core that wishes its local interrupt to be delivered. Based on an initial patch by Thomas Gleixner. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-23 16:03:06 +00:00
return __irq_get_desc_lock(irq, flags, false, check);
}
static inline void
irq_put_desc_unlock(struct irq_desc *desc, unsigned long flags)
{
__irq_put_desc_unlock(desc, flags, false);
}
#define __irqd_to_state(d) ACCESS_PRIVATE((d)->common, state_use_accessors)
genirq/debugfs: Add proper debugfs interface Debugging (hierarchical) interupt domains is tedious as there is no information about the hierarchy and no information about states of interrupts in the various domain levels. Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'. The domains directory contains the domain files. The content is information about the domain. If the domain is part of a hierarchy then the parent domains are printed as well. # ls /sys/kernel/debug/irq/domains/ default INTEL-IR-2 INTEL-IR-MSI-2 IO-APIC-IR-2 PCI-MSI DMAR-MSI INTEL-IR-3 INTEL-IR-MSI-3 IO-APIC-IR-3 unknown-1 INTEL-IR-0 INTEL-IR-MSI-0 IO-APIC-IR-0 IO-APIC-IR-4 VECTOR INTEL-IR-1 INTEL-IR-MSI-1 IO-APIC-IR-1 PCI-HT # cat /sys/kernel/debug/irq/domains/VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 # cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0 name: IO-APIC-IR-0 size: 24 mapped: 19 flags: 0x00000041 parent: INTEL-IR-3 name: INTEL-IR-3 size: 65536 mapped: 167 flags: 0x00000041 parent: VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 Unfortunately there is no per cpu information about the VECTOR domain (yet). The irqs directory contains detailed information about mapped interrupts. # cat /sys/kernel/debug/irq/irqs/3 handler: handle_edge_irq status: 0x00004000 istate: 0x00000000 ddepth: 1 wdepth: 0 dstate: 0x01018000 IRQD_IRQ_DISABLED IRQD_SINGLE_TARGET IRQD_MOVE_PCNTXT node: 0 affinity: 0-143 effectiv: 0 pending: domain: IO-APIC-IR-0 hwirq: 0x3 chip: IR-IO-APIC flags: 0x10 IRQCHIP_SKIP_SET_WAKE parent: domain: INTEL-IR-3 hwirq: 0x20000 chip: INTEL-IR flags: 0x0 parent: domain: VECTOR hwirq: 0x3 chip: APIC flags: 0x0 This was developed to simplify the debugging of the managed affinity changes. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2017-06-19 23:37:17 +00:00
static inline unsigned int irqd_get(struct irq_data *d)
{
return __irqd_to_state(d);
}
/*
* Manipulation functions for irq_data.state
*/
static inline void irqd_set_move_pending(struct irq_data *d)
{
__irqd_to_state(d) |= IRQD_SETAFFINITY_PENDING;
}
static inline void irqd_clr_move_pending(struct irq_data *d)
{
__irqd_to_state(d) &= ~IRQD_SETAFFINITY_PENDING;
}
static inline void irqd_set_managed_shutdown(struct irq_data *d)
{
__irqd_to_state(d) |= IRQD_MANAGED_SHUTDOWN;
}
static inline void irqd_clr_managed_shutdown(struct irq_data *d)
{
__irqd_to_state(d) &= ~IRQD_MANAGED_SHUTDOWN;
}
static inline void irqd_clear(struct irq_data *d, unsigned int mask)
{
__irqd_to_state(d) &= ~mask;
}
static inline void irqd_set(struct irq_data *d, unsigned int mask)
{
__irqd_to_state(d) |= mask;
}
static inline bool irqd_has_set(struct irq_data *d, unsigned int mask)
{
return __irqd_to_state(d) & mask;
}
#undef __irqd_to_state
static inline void kstat_incr_irqs_this_cpu(struct irq_desc *desc)
{
__this_cpu_inc(*desc->kstat_irqs);
__this_cpu_inc(kstat.irqs_sum);
}
static inline int irq_desc_get_node(struct irq_desc *desc)
{
return irq_common_data_get_node(&desc->irq_common_data);
}
genirq/PM: Restore system wake up from chained interrupts Commit e509bd7da149 ("genirq: Allow migration of chained interrupts by installing default action") breaks PCS wake up IRQ behaviour on TI OMAP based platforms (dra7-evm). TI OMAP IRQ wake up configuration: GIC-irqchip->PCM_IRQ |- omap_prcm_register_chain_handler |- PRCM-irqchip -> PRCM_IO_IRQ |- pcs_irq_chain_handler |- pinctrl-irqchip -> PCS_uart1_wakeup_irq This happens because IRQ PM code (irq/pm.c) is expected to ignore chained interrupts by default: static bool suspend_device_irq(struct irq_desc *desc) { if (!desc->action || desc->no_suspend_depth) return false; - it's expected !desc->action = true for chained interrupts; but, after above change, all chained interrupt descriptors will have default action handler installed - chained_action. As result, chained interrupts will be silently disabled during system suspend. Hence, fix it by introducing helper function irq_desc_is_chained() and use it in suspend_device_irq() for chained interrupts identification and skip them, once detected. Fixes: e509bd7da149 ("genirq: Allow migration of chained interrupts..") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Tony Lindgren <tony@atomide.com> Cc: <nsekhar@ti.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: Tony Lindgren <tony@atomide.com> Link: http://lkml.kernel.org/r/1447149492-20699-1-git-send-email-grygorii.strashko@ti.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-11-10 09:58:12 +00:00
static inline int irq_desc_is_chained(struct irq_desc *desc)
{
return (desc->action && desc->action == &chained_action);
}
#ifdef CONFIG_PM_SLEEP
bool irq_pm_check_wakeup(struct irq_desc *desc);
void irq_pm_install_action(struct irq_desc *desc, struct irqaction *action);
void irq_pm_remove_action(struct irq_desc *desc, struct irqaction *action);
#else
static inline bool irq_pm_check_wakeup(struct irq_desc *desc) { return false; }
static inline void
irq_pm_install_action(struct irq_desc *desc, struct irqaction *action) { }
static inline void
irq_pm_remove_action(struct irq_desc *desc, struct irqaction *action) { }
#endif
#ifdef CONFIG_GENERIC_IRQ_CHIP
void irq_init_generic_chip(struct irq_chip_generic *gc, const char *name,
int num_ct, unsigned int irq_base,
void __iomem *reg_base, irq_flow_handler_t handler);
#else
static inline void
irq_init_generic_chip(struct irq_chip_generic *gc, const char *name,
int num_ct, unsigned int irq_base,
void __iomem *reg_base, irq_flow_handler_t handler) { }
#endif /* CONFIG_GENERIC_IRQ_CHIP */
genirq/debugfs: Add proper debugfs interface Debugging (hierarchical) interupt domains is tedious as there is no information about the hierarchy and no information about states of interrupts in the various domain levels. Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'. The domains directory contains the domain files. The content is information about the domain. If the domain is part of a hierarchy then the parent domains are printed as well. # ls /sys/kernel/debug/irq/domains/ default INTEL-IR-2 INTEL-IR-MSI-2 IO-APIC-IR-2 PCI-MSI DMAR-MSI INTEL-IR-3 INTEL-IR-MSI-3 IO-APIC-IR-3 unknown-1 INTEL-IR-0 INTEL-IR-MSI-0 IO-APIC-IR-0 IO-APIC-IR-4 VECTOR INTEL-IR-1 INTEL-IR-MSI-1 IO-APIC-IR-1 PCI-HT # cat /sys/kernel/debug/irq/domains/VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 # cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0 name: IO-APIC-IR-0 size: 24 mapped: 19 flags: 0x00000041 parent: INTEL-IR-3 name: INTEL-IR-3 size: 65536 mapped: 167 flags: 0x00000041 parent: VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 Unfortunately there is no per cpu information about the VECTOR domain (yet). The irqs directory contains detailed information about mapped interrupts. # cat /sys/kernel/debug/irq/irqs/3 handler: handle_edge_irq status: 0x00004000 istate: 0x00000000 ddepth: 1 wdepth: 0 dstate: 0x01018000 IRQD_IRQ_DISABLED IRQD_SINGLE_TARGET IRQD_MOVE_PCNTXT node: 0 affinity: 0-143 effectiv: 0 pending: domain: IO-APIC-IR-0 hwirq: 0x3 chip: IR-IO-APIC flags: 0x10 IRQCHIP_SKIP_SET_WAKE parent: domain: INTEL-IR-3 hwirq: 0x20000 chip: INTEL-IR flags: 0x0 parent: domain: VECTOR hwirq: 0x3 chip: APIC flags: 0x0 This was developed to simplify the debugging of the managed affinity changes. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2017-06-19 23:37:17 +00:00
#ifdef CONFIG_GENERIC_PENDING_IRQ
static inline bool irq_can_move_pcntxt(struct irq_data *data)
{
return irqd_can_move_in_process_context(data);
}
static inline bool irq_move_pending(struct irq_data *data)
{
return irqd_is_setaffinity_pending(data);
}
static inline void
irq_copy_pending(struct irq_desc *desc, const struct cpumask *mask)
{
cpumask_copy(desc->pending_mask, mask);
}
static inline void
irq_get_pending(struct cpumask *mask, struct irq_desc *desc)
{
cpumask_copy(mask, desc->pending_mask);
}
static inline struct cpumask *irq_desc_get_pending_mask(struct irq_desc *desc)
{
return desc->pending_mask;
}
bool irq_fixup_move_pending(struct irq_desc *desc, bool force_clear);
#else /* CONFIG_GENERIC_PENDING_IRQ */
static inline bool irq_can_move_pcntxt(struct irq_data *data)
{
return true;
}
static inline bool irq_move_pending(struct irq_data *data)
{
return false;
}
static inline void
irq_copy_pending(struct irq_desc *desc, const struct cpumask *mask)
{
}
static inline void
irq_get_pending(struct cpumask *mask, struct irq_desc *desc)
{
}
static inline struct cpumask *irq_desc_get_pending_mask(struct irq_desc *desc)
{
return NULL;
}
static inline bool irq_fixup_move_pending(struct irq_desc *desc, bool fclear)
{
return false;
}
#endif /* !CONFIG_GENERIC_PENDING_IRQ */
genirq/debugfs: Add proper debugfs interface Debugging (hierarchical) interupt domains is tedious as there is no information about the hierarchy and no information about states of interrupts in the various domain levels. Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'. The domains directory contains the domain files. The content is information about the domain. If the domain is part of a hierarchy then the parent domains are printed as well. # ls /sys/kernel/debug/irq/domains/ default INTEL-IR-2 INTEL-IR-MSI-2 IO-APIC-IR-2 PCI-MSI DMAR-MSI INTEL-IR-3 INTEL-IR-MSI-3 IO-APIC-IR-3 unknown-1 INTEL-IR-0 INTEL-IR-MSI-0 IO-APIC-IR-0 IO-APIC-IR-4 VECTOR INTEL-IR-1 INTEL-IR-MSI-1 IO-APIC-IR-1 PCI-HT # cat /sys/kernel/debug/irq/domains/VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 # cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0 name: IO-APIC-IR-0 size: 24 mapped: 19 flags: 0x00000041 parent: INTEL-IR-3 name: INTEL-IR-3 size: 65536 mapped: 167 flags: 0x00000041 parent: VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 Unfortunately there is no per cpu information about the VECTOR domain (yet). The irqs directory contains detailed information about mapped interrupts. # cat /sys/kernel/debug/irq/irqs/3 handler: handle_edge_irq status: 0x00004000 istate: 0x00000000 ddepth: 1 wdepth: 0 dstate: 0x01018000 IRQD_IRQ_DISABLED IRQD_SINGLE_TARGET IRQD_MOVE_PCNTXT node: 0 affinity: 0-143 effectiv: 0 pending: domain: IO-APIC-IR-0 hwirq: 0x3 chip: IR-IO-APIC flags: 0x10 IRQCHIP_SKIP_SET_WAKE parent: domain: INTEL-IR-3 hwirq: 0x20000 chip: INTEL-IR flags: 0x0 parent: domain: VECTOR hwirq: 0x3 chip: APIC flags: 0x0 This was developed to simplify the debugging of the managed affinity changes. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2017-06-19 23:37:17 +00:00
#ifdef CONFIG_GENERIC_IRQ_DEBUGFS
#include <linux/debugfs.h>
genirq/debugfs: Add proper debugfs interface Debugging (hierarchical) interupt domains is tedious as there is no information about the hierarchy and no information about states of interrupts in the various domain levels. Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'. The domains directory contains the domain files. The content is information about the domain. If the domain is part of a hierarchy then the parent domains are printed as well. # ls /sys/kernel/debug/irq/domains/ default INTEL-IR-2 INTEL-IR-MSI-2 IO-APIC-IR-2 PCI-MSI DMAR-MSI INTEL-IR-3 INTEL-IR-MSI-3 IO-APIC-IR-3 unknown-1 INTEL-IR-0 INTEL-IR-MSI-0 IO-APIC-IR-0 IO-APIC-IR-4 VECTOR INTEL-IR-1 INTEL-IR-MSI-1 IO-APIC-IR-1 PCI-HT # cat /sys/kernel/debug/irq/domains/VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 # cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0 name: IO-APIC-IR-0 size: 24 mapped: 19 flags: 0x00000041 parent: INTEL-IR-3 name: INTEL-IR-3 size: 65536 mapped: 167 flags: 0x00000041 parent: VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 Unfortunately there is no per cpu information about the VECTOR domain (yet). The irqs directory contains detailed information about mapped interrupts. # cat /sys/kernel/debug/irq/irqs/3 handler: handle_edge_irq status: 0x00004000 istate: 0x00000000 ddepth: 1 wdepth: 0 dstate: 0x01018000 IRQD_IRQ_DISABLED IRQD_SINGLE_TARGET IRQD_MOVE_PCNTXT node: 0 affinity: 0-143 effectiv: 0 pending: domain: IO-APIC-IR-0 hwirq: 0x3 chip: IR-IO-APIC flags: 0x10 IRQCHIP_SKIP_SET_WAKE parent: domain: INTEL-IR-3 hwirq: 0x20000 chip: INTEL-IR flags: 0x0 parent: domain: VECTOR hwirq: 0x3 chip: APIC flags: 0x0 This was developed to simplify the debugging of the managed affinity changes. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2017-06-19 23:37:17 +00:00
void irq_add_debugfs_entry(unsigned int irq, struct irq_desc *desc);
static inline void irq_remove_debugfs_entry(struct irq_desc *desc)
{
debugfs_remove(desc->debugfs_file);
}
genirq/debugfs: Add proper debugfs interface Debugging (hierarchical) interupt domains is tedious as there is no information about the hierarchy and no information about states of interrupts in the various domain levels. Add a debugfs directory 'irq' and subdirectories 'domains' and 'irqs'. The domains directory contains the domain files. The content is information about the domain. If the domain is part of a hierarchy then the parent domains are printed as well. # ls /sys/kernel/debug/irq/domains/ default INTEL-IR-2 INTEL-IR-MSI-2 IO-APIC-IR-2 PCI-MSI DMAR-MSI INTEL-IR-3 INTEL-IR-MSI-3 IO-APIC-IR-3 unknown-1 INTEL-IR-0 INTEL-IR-MSI-0 IO-APIC-IR-0 IO-APIC-IR-4 VECTOR INTEL-IR-1 INTEL-IR-MSI-1 IO-APIC-IR-1 PCI-HT # cat /sys/kernel/debug/irq/domains/VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 # cat /sys/kernel/debug/irq/domains/IO-APIC-IR-0 name: IO-APIC-IR-0 size: 24 mapped: 19 flags: 0x00000041 parent: INTEL-IR-3 name: INTEL-IR-3 size: 65536 mapped: 167 flags: 0x00000041 parent: VECTOR name: VECTOR size: 0 mapped: 216 flags: 0x00000041 Unfortunately there is no per cpu information about the VECTOR domain (yet). The irqs directory contains detailed information about mapped interrupts. # cat /sys/kernel/debug/irq/irqs/3 handler: handle_edge_irq status: 0x00004000 istate: 0x00000000 ddepth: 1 wdepth: 0 dstate: 0x01018000 IRQD_IRQ_DISABLED IRQD_SINGLE_TARGET IRQD_MOVE_PCNTXT node: 0 affinity: 0-143 effectiv: 0 pending: domain: IO-APIC-IR-0 hwirq: 0x3 chip: IR-IO-APIC flags: 0x10 IRQCHIP_SKIP_SET_WAKE parent: domain: INTEL-IR-3 hwirq: 0x20000 chip: INTEL-IR flags: 0x0 parent: domain: VECTOR hwirq: 0x3 chip: APIC flags: 0x0 This was developed to simplify the debugging of the managed affinity changes. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Keith Busch <keith.busch@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20170619235444.537566163@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2017-06-19 23:37:17 +00:00
# ifdef CONFIG_IRQ_DOMAIN
void irq_domain_debugfs_init(struct dentry *root);
# else
static inline void irq_domain_debugfs_init(struct dentry *root);
# endif
#else /* CONFIG_GENERIC_IRQ_DEBUGFS */
static inline void irq_add_debugfs_entry(unsigned int irq, struct irq_desc *d)
{
}
static inline void irq_remove_debugfs_entry(struct irq_desc *d)
{
}
#endif /* CONFIG_GENERIC_IRQ_DEBUGFS */