linux/drivers/soundwire/intel.c

1348 lines
34 KiB
C
Raw Normal View History

// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
// Copyright(c) 2015-17 Intel Corporation.
/*
* Soundwire Intel Master Driver
*/
#include <linux/acpi.h>
#include <linux/debugfs.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <sound/pcm_params.h>
#include <linux/pm_runtime.h>
#include <sound/soc.h>
#include <linux/soundwire/sdw_registers.h>
#include <linux/soundwire/sdw.h>
#include <linux/soundwire/sdw_intel.h>
#include "cadence_master.h"
#include "bus.h"
#include "intel.h"
static int intel_wait_bit(void __iomem *base, int offset, u32 mask, u32 target)
{
int timeout = 10;
u32 reg_read;
do {
reg_read = readl(base + offset);
if ((reg_read & mask) == target)
return 0;
timeout--;
usleep_range(50, 100);
} while (timeout != 0);
return -EAGAIN;
}
static int intel_clear_bit(void __iomem *base, int offset, u32 value, u32 mask)
{
writel(value, base + offset);
return intel_wait_bit(base, offset, mask, 0);
}
static int intel_set_bit(void __iomem *base, int offset, u32 value, u32 mask)
{
writel(value, base + offset);
return intel_wait_bit(base, offset, mask, mask);
}
/*
* debugfs
*/
#ifdef CONFIG_DEBUG_FS
#define RD_BUF (2 * PAGE_SIZE)
static ssize_t intel_sprintf(void __iomem *mem, bool l,
char *buf, size_t pos, unsigned int reg)
{
int value;
if (l)
value = intel_readl(mem, reg);
else
value = intel_readw(mem, reg);
return scnprintf(buf + pos, RD_BUF - pos, "%4x\t%4x\n", reg, value);
}
static int intel_reg_show(struct seq_file *s_file, void *data)
{
struct sdw_intel *sdw = s_file->private;
void __iomem *s = sdw->link_res->shim;
void __iomem *a = sdw->link_res->alh;
char *buf;
ssize_t ret;
int i, j;
unsigned int links, reg;
buf = kzalloc(RD_BUF, GFP_KERNEL);
if (!buf)
return -ENOMEM;
links = intel_readl(s, SDW_SHIM_LCAP) & SDW_SHIM_LCAP_LCOUNT_MASK;
ret = scnprintf(buf, RD_BUF, "Register Value\n");
ret += scnprintf(buf + ret, RD_BUF - ret, "\nShim\n");
for (i = 0; i < links; i++) {
reg = SDW_SHIM_LCAP + i * 4;
ret += intel_sprintf(s, true, buf, ret, reg);
}
for (i = 0; i < links; i++) {
ret += scnprintf(buf + ret, RD_BUF - ret, "\nLink%d\n", i);
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_CTLSCAP(i));
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_CTLS0CM(i));
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_CTLS1CM(i));
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_CTLS2CM(i));
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_CTLS3CM(i));
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_PCMSCAP(i));
ret += scnprintf(buf + ret, RD_BUF - ret, "\n PCMSyCH registers\n");
/*
* the value 10 is the number of PDIs. We will need a
* cleanup to remove hard-coded Intel configurations
* from cadence_master.c
*/
for (j = 0; j < 10; j++) {
ret += intel_sprintf(s, false, buf, ret,
SDW_SHIM_PCMSYCHM(i, j));
ret += intel_sprintf(s, false, buf, ret,
SDW_SHIM_PCMSYCHC(i, j));
}
ret += scnprintf(buf + ret, RD_BUF - ret, "\n IOCTL, CTMCTL\n");
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_IOCTL(i));
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_CTMCTL(i));
}
ret += scnprintf(buf + ret, RD_BUF - ret, "\nWake registers\n");
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_WAKEEN);
ret += intel_sprintf(s, false, buf, ret, SDW_SHIM_WAKESTS);
ret += scnprintf(buf + ret, RD_BUF - ret, "\nALH STRMzCFG\n");
for (i = 0; i < SDW_ALH_NUM_STREAMS; i++)
ret += intel_sprintf(a, true, buf, ret, SDW_ALH_STRMZCFG(i));
seq_printf(s_file, "%s", buf);
kfree(buf);
return 0;
}
DEFINE_SHOW_ATTRIBUTE(intel_reg);
static int intel_set_m_datamode(void *data, u64 value)
{
struct sdw_intel *sdw = data;
struct sdw_bus *bus = &sdw->cdns.bus;
if (value > SDW_PORT_DATA_MODE_STATIC_1)
return -EINVAL;
/* Userspace changed the hardware state behind the kernel's back */
add_taint(TAINT_USER, LOCKDEP_STILL_OK);
bus->params.m_data_mode = value;
return 0;
}
DEFINE_DEBUGFS_ATTRIBUTE(intel_set_m_datamode_fops, NULL,
intel_set_m_datamode, "%llu\n");
static int intel_set_s_datamode(void *data, u64 value)
{
struct sdw_intel *sdw = data;
struct sdw_bus *bus = &sdw->cdns.bus;
if (value > SDW_PORT_DATA_MODE_STATIC_1)
return -EINVAL;
/* Userspace changed the hardware state behind the kernel's back */
add_taint(TAINT_USER, LOCKDEP_STILL_OK);
bus->params.s_data_mode = value;
return 0;
}
DEFINE_DEBUGFS_ATTRIBUTE(intel_set_s_datamode_fops, NULL,
intel_set_s_datamode, "%llu\n");
static void intel_debugfs_init(struct sdw_intel *sdw)
{
struct dentry *root = sdw->cdns.bus.debugfs;
if (!root)
return;
sdw->debugfs = debugfs_create_dir("intel-sdw", root);
debugfs_create_file("intel-registers", 0400, sdw->debugfs, sdw,
&intel_reg_fops);
debugfs_create_file("intel-m-datamode", 0200, sdw->debugfs, sdw,
&intel_set_m_datamode_fops);
debugfs_create_file("intel-s-datamode", 0200, sdw->debugfs, sdw,
&intel_set_s_datamode_fops);
sdw_cdns_debugfs_init(&sdw->cdns, sdw->debugfs);
}
static void intel_debugfs_exit(struct sdw_intel *sdw)
{
debugfs_remove_recursive(sdw->debugfs);
}
#else
static void intel_debugfs_init(struct sdw_intel *sdw) {}
static void intel_debugfs_exit(struct sdw_intel *sdw) {}
#endif /* CONFIG_DEBUG_FS */
/*
* shim ops
*/
/* this needs to be called with shim_lock */
static void intel_shim_glue_to_master_ip(struct sdw_intel *sdw)
{
void __iomem *shim = sdw->link_res->shim;
unsigned int link_id = sdw->instance;
u16 ioctl;
/* Switch to MIP from Glue logic */
ioctl = intel_readw(shim, SDW_SHIM_IOCTL(link_id));
ioctl &= ~(SDW_SHIM_IOCTL_DOE);
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl &= ~(SDW_SHIM_IOCTL_DO);
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl |= (SDW_SHIM_IOCTL_MIF);
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl &= ~(SDW_SHIM_IOCTL_BKE);
ioctl &= ~(SDW_SHIM_IOCTL_COE);
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
/* at this point Master IP has full control of the I/Os */
}
/* this needs to be called with shim_lock */
static void intel_shim_master_ip_to_glue(struct sdw_intel *sdw)
{
unsigned int link_id = sdw->instance;
void __iomem *shim = sdw->link_res->shim;
u16 ioctl;
/* Glue logic */
ioctl = intel_readw(shim, SDW_SHIM_IOCTL(link_id));
ioctl |= SDW_SHIM_IOCTL_BKE;
ioctl |= SDW_SHIM_IOCTL_COE;
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl &= ~(SDW_SHIM_IOCTL_MIF);
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
/* at this point Integration Glue has full control of the I/Os */
}
/* this needs to be called with shim_lock */
static void intel_shim_init(struct sdw_intel *sdw)
{
void __iomem *shim = sdw->link_res->shim;
unsigned int link_id = sdw->instance;
u16 ioctl = 0, act = 0;
/* Initialize Shim */
ioctl |= SDW_SHIM_IOCTL_BKE;
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl |= SDW_SHIM_IOCTL_WPDD;
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl |= SDW_SHIM_IOCTL_DO;
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
ioctl |= SDW_SHIM_IOCTL_DOE;
intel_writew(shim, SDW_SHIM_IOCTL(link_id), ioctl);
usleep_range(10, 15);
intel_shim_glue_to_master_ip(sdw);
u16p_replace_bits(&act, 0x1, SDW_SHIM_CTMCTL_DOAIS);
act |= SDW_SHIM_CTMCTL_DACTQE;
act |= SDW_SHIM_CTMCTL_DODS;
intel_writew(shim, SDW_SHIM_CTMCTL(link_id), act);
usleep_range(10, 15);
}
static int intel_shim_check_wake(struct sdw_intel *sdw)
{
void __iomem *shim;
u16 wake_sts;
shim = sdw->link_res->shim;
wake_sts = intel_readw(shim, SDW_SHIM_WAKESTS);
return wake_sts & BIT(sdw->instance);
}
static void intel_shim_wake(struct sdw_intel *sdw, bool wake_enable)
{
void __iomem *shim = sdw->link_res->shim;
unsigned int link_id = sdw->instance;
u16 wake_en, wake_sts;
mutex_lock(sdw->link_res->shim_lock);
wake_en = intel_readw(shim, SDW_SHIM_WAKEEN);
if (wake_enable) {
/* Enable the wakeup */
wake_en |= (SDW_SHIM_WAKEEN_ENABLE << link_id);
intel_writew(shim, SDW_SHIM_WAKEEN, wake_en);
} else {
/* Disable the wake up interrupt */
wake_en &= ~(SDW_SHIM_WAKEEN_ENABLE << link_id);
intel_writew(shim, SDW_SHIM_WAKEEN, wake_en);
/* Clear wake status */
wake_sts = intel_readw(shim, SDW_SHIM_WAKESTS);
wake_sts |= (SDW_SHIM_WAKESTS_STATUS << link_id);
intel_writew(shim, SDW_SHIM_WAKESTS, wake_sts);
}
mutex_unlock(sdw->link_res->shim_lock);
}
static int intel_link_power_up(struct sdw_intel *sdw)
{
unsigned int link_id = sdw->instance;
void __iomem *shim = sdw->link_res->shim;
u32 *shim_mask = sdw->link_res->shim_mask;
struct sdw_bus *bus = &sdw->cdns.bus;
struct sdw_master_prop *prop = &bus->prop;
u32 spa_mask, cpa_mask;
u32 link_control;
int ret = 0;
u32 syncprd;
u32 sync_reg;
mutex_lock(sdw->link_res->shim_lock);
/*
* The hardware relies on an internal counter, typically 4kHz,
* to generate the SoundWire SSP - which defines a 'safe'
* synchronization point between commands and audio transport
* and allows for multi link synchronization. The SYNCPRD value
* is only dependent on the oscillator clock provided to
* the IP, so adjust based on _DSD properties reported in DSDT
* tables. The values reported are based on either 24MHz
* (CNL/CML) or 38.4 MHz (ICL/TGL+).
*/
if (prop->mclk_freq % 6000000)
syncprd = SDW_SHIM_SYNC_SYNCPRD_VAL_38_4;
else
syncprd = SDW_SHIM_SYNC_SYNCPRD_VAL_24;
if (!*shim_mask) {
dev_dbg(sdw->cdns.dev, "powering up all links\n");
/* we first need to program the SyncPRD/CPU registers */
dev_dbg(sdw->cdns.dev,
"first link up, programming SYNCPRD\n");
/* set SyncPRD period */
sync_reg = intel_readl(shim, SDW_SHIM_SYNC);
u32p_replace_bits(&sync_reg, syncprd, SDW_SHIM_SYNC_SYNCPRD);
/* Set SyncCPU bit */
sync_reg |= SDW_SHIM_SYNC_SYNCCPU;
intel_writel(shim, SDW_SHIM_SYNC, sync_reg);
/* Link power up sequence */
link_control = intel_readl(shim, SDW_SHIM_LCTL);
/* only power-up enabled links */
spa_mask = FIELD_PREP(SDW_SHIM_LCTL_SPA_MASK, sdw->link_res->link_mask);
cpa_mask = FIELD_PREP(SDW_SHIM_LCTL_CPA_MASK, sdw->link_res->link_mask);
link_control |= spa_mask;
ret = intel_set_bit(shim, SDW_SHIM_LCTL, link_control, cpa_mask);
if (ret < 0) {
dev_err(sdw->cdns.dev, "Failed to power up link: %d\n", ret);
goto out;
}
/* SyncCPU will change once link is active */
ret = intel_wait_bit(shim, SDW_SHIM_SYNC,
SDW_SHIM_SYNC_SYNCCPU, 0);
if (ret < 0) {
dev_err(sdw->cdns.dev,
"Failed to set SHIM_SYNC: %d\n", ret);
goto out;
}
}
*shim_mask |= BIT(link_id);
sdw->cdns.link_up = true;
intel_shim_init(sdw);
out:
mutex_unlock(sdw->link_res->shim_lock);
return ret;
}
static int intel_link_power_down(struct sdw_intel *sdw)
{
u32 link_control, spa_mask, cpa_mask;
unsigned int link_id = sdw->instance;
void __iomem *shim = sdw->link_res->shim;
u32 *shim_mask = sdw->link_res->shim_mask;
int ret = 0;
mutex_lock(sdw->link_res->shim_lock);
if (!(*shim_mask & BIT(link_id)))
dev_err(sdw->cdns.dev,
"%s: Unbalanced power-up/down calls\n", __func__);
sdw->cdns.link_up = false;
intel_shim_master_ip_to_glue(sdw);
*shim_mask &= ~BIT(link_id);
if (!*shim_mask) {
dev_dbg(sdw->cdns.dev, "powering down all links\n");
/* Link power down sequence */
link_control = intel_readl(shim, SDW_SHIM_LCTL);
/* only power-down enabled links */
spa_mask = FIELD_PREP(SDW_SHIM_LCTL_SPA_MASK, ~sdw->link_res->link_mask);
cpa_mask = FIELD_PREP(SDW_SHIM_LCTL_CPA_MASK, sdw->link_res->link_mask);
link_control &= spa_mask;
ret = intel_clear_bit(shim, SDW_SHIM_LCTL, link_control, cpa_mask);
if (ret < 0) {
dev_err(sdw->cdns.dev, "%s: could not power down link\n", __func__);
/*
* we leave the sdw->cdns.link_up flag as false since we've disabled
* the link at this point and cannot handle interrupts any longer.
*/
}
}
mutex_unlock(sdw->link_res->shim_lock);
return ret;
}
static void intel_shim_sync_arm(struct sdw_intel *sdw)
{
void __iomem *shim = sdw->link_res->shim;
u32 sync_reg;
mutex_lock(sdw->link_res->shim_lock);
/* update SYNC register */
sync_reg = intel_readl(shim, SDW_SHIM_SYNC);
sync_reg |= (SDW_SHIM_SYNC_CMDSYNC << sdw->instance);
intel_writel(shim, SDW_SHIM_SYNC, sync_reg);
mutex_unlock(sdw->link_res->shim_lock);
}
static int intel_shim_sync_go_unlocked(struct sdw_intel *sdw)
{
void __iomem *shim = sdw->link_res->shim;
u32 sync_reg;
/* Read SYNC register */
sync_reg = intel_readl(shim, SDW_SHIM_SYNC);
/*
* Set SyncGO bit to synchronously trigger a bank switch for
* all the masters. A write to SYNCGO bit clears CMDSYNC bit for all
* the Masters.
*/
sync_reg |= SDW_SHIM_SYNC_SYNCGO;
intel_writel(shim, SDW_SHIM_SYNC, sync_reg);
return 0;
}
static int intel_shim_sync_go(struct sdw_intel *sdw)
{
int ret;
mutex_lock(sdw->link_res->shim_lock);
ret = intel_shim_sync_go_unlocked(sdw);
mutex_unlock(sdw->link_res->shim_lock);
return ret;
}
/*
* PDI routines
*/
static void intel_pdi_init(struct sdw_intel *sdw,
struct sdw_cdns_stream_config *config)
{
void __iomem *shim = sdw->link_res->shim;
unsigned int link_id = sdw->instance;
int pcm_cap;
/* PCM Stream Capability */
pcm_cap = intel_readw(shim, SDW_SHIM_PCMSCAP(link_id));
config->pcm_bd = FIELD_GET(SDW_SHIM_PCMSCAP_BSS, pcm_cap);
config->pcm_in = FIELD_GET(SDW_SHIM_PCMSCAP_ISS, pcm_cap);
config->pcm_out = FIELD_GET(SDW_SHIM_PCMSCAP_OSS, pcm_cap);
dev_dbg(sdw->cdns.dev, "PCM cap bd:%d in:%d out:%d\n",
config->pcm_bd, config->pcm_in, config->pcm_out);
}
static int
intel_pdi_get_ch_cap(struct sdw_intel *sdw, unsigned int pdi_num)
{
void __iomem *shim = sdw->link_res->shim;
unsigned int link_id = sdw->instance;
int count;
count = intel_readw(shim, SDW_SHIM_PCMSYCHC(link_id, pdi_num));
/*
* WORKAROUND: on all existing Intel controllers, pdi
* number 2 reports channel count as 1 even though it
* supports 8 channels. Performing hardcoding for pdi
* number 2.
*/
if (pdi_num == 2)
count = 7;
/* zero based values for channel count in register */
count++;
return count;
}
static int intel_pdi_get_ch_update(struct sdw_intel *sdw,
struct sdw_cdns_pdi *pdi,
unsigned int num_pdi,
unsigned int *num_ch)
{
int i, ch_count = 0;
for (i = 0; i < num_pdi; i++) {
pdi->ch_count = intel_pdi_get_ch_cap(sdw, pdi->num);
ch_count += pdi->ch_count;
pdi++;
}
*num_ch = ch_count;
return 0;
}
static int intel_pdi_stream_ch_update(struct sdw_intel *sdw,
struct sdw_cdns_streams *stream)
{
intel_pdi_get_ch_update(sdw, stream->bd, stream->num_bd,
&stream->num_ch_bd);
intel_pdi_get_ch_update(sdw, stream->in, stream->num_in,
&stream->num_ch_in);
intel_pdi_get_ch_update(sdw, stream->out, stream->num_out,
&stream->num_ch_out);
return 0;
}
static void
intel_pdi_shim_configure(struct sdw_intel *sdw, struct sdw_cdns_pdi *pdi)
{
void __iomem *shim = sdw->link_res->shim;
unsigned int link_id = sdw->instance;
int pdi_conf = 0;
/* the Bulk and PCM streams are not contiguous */
pdi->intel_alh_id = (link_id * 16) + pdi->num + 3;
if (pdi->num >= 2)
pdi->intel_alh_id += 2;
/*
* Program stream parameters to stream SHIM register
* This is applicable for PCM stream only.
*/
if (pdi->type != SDW_STREAM_PCM)
return;
if (pdi->dir == SDW_DATA_DIR_RX)
pdi_conf |= SDW_SHIM_PCMSYCM_DIR;
else
pdi_conf &= ~(SDW_SHIM_PCMSYCM_DIR);
u32p_replace_bits(&pdi_conf, pdi->intel_alh_id, SDW_SHIM_PCMSYCM_STREAM);
u32p_replace_bits(&pdi_conf, pdi->l_ch_num, SDW_SHIM_PCMSYCM_LCHN);
u32p_replace_bits(&pdi_conf, pdi->h_ch_num, SDW_SHIM_PCMSYCM_HCHN);
intel_writew(shim, SDW_SHIM_PCMSYCHM(link_id, pdi->num), pdi_conf);
}
static void
intel_pdi_alh_configure(struct sdw_intel *sdw, struct sdw_cdns_pdi *pdi)
{
void __iomem *alh = sdw->link_res->alh;
unsigned int link_id = sdw->instance;
unsigned int conf;
/* the Bulk and PCM streams are not contiguous */
pdi->intel_alh_id = (link_id * 16) + pdi->num + 3;
if (pdi->num >= 2)
pdi->intel_alh_id += 2;
/* Program Stream config ALH register */
conf = intel_readl(alh, SDW_ALH_STRMZCFG(pdi->intel_alh_id));
u32p_replace_bits(&conf, SDW_ALH_STRMZCFG_DMAT_VAL, SDW_ALH_STRMZCFG_DMAT);
u32p_replace_bits(&conf, pdi->ch_count - 1, SDW_ALH_STRMZCFG_CHN);
intel_writel(alh, SDW_ALH_STRMZCFG(pdi->intel_alh_id), conf);
}
static int intel_params_stream(struct sdw_intel *sdw,
int stream,
struct snd_soc_dai *dai,
struct snd_pcm_hw_params *hw_params,
int link_id, int alh_stream_id)
{
struct sdw_intel_link_res *res = sdw->link_res;
struct sdw_intel_stream_params_data params_data;
params_data.stream = stream; /* direction */
params_data.dai = dai;
params_data.hw_params = hw_params;
params_data.link_id = link_id;
params_data.alh_stream_id = alh_stream_id;
if (res->ops && res->ops->params_stream && res->dev)
return res->ops->params_stream(res->dev,
&params_data);
return -EIO;
}
static int intel_free_stream(struct sdw_intel *sdw,
int stream,
struct snd_soc_dai *dai,
int link_id)
{
struct sdw_intel_link_res *res = sdw->link_res;
struct sdw_intel_stream_free_data free_data;
free_data.stream = stream; /* direction */
free_data.dai = dai;
free_data.link_id = link_id;
if (res->ops && res->ops->free_stream && res->dev)
return res->ops->free_stream(res->dev,
&free_data);
return 0;
}
/*
* bank switch routines
*/
static int intel_pre_bank_switch(struct sdw_intel *sdw)
{
struct sdw_cdns *cdns = &sdw->cdns;
struct sdw_bus *bus = &cdns->bus;
/* Write to register only for multi-link */
if (!bus->multi_link)
return 0;
intel_shim_sync_arm(sdw);
return 0;
}
static int intel_post_bank_switch(struct sdw_intel *sdw)
{
struct sdw_cdns *cdns = &sdw->cdns;
struct sdw_bus *bus = &cdns->bus;
void __iomem *shim = sdw->link_res->shim;
int sync_reg, ret;
/* Write to register only for multi-link */
if (!bus->multi_link)
return 0;
mutex_lock(sdw->link_res->shim_lock);
/* Read SYNC register */
sync_reg = intel_readl(shim, SDW_SHIM_SYNC);
/*
* post_bank_switch() ops is called from the bus in loop for
* all the Masters in the steam with the expectation that
* we trigger the bankswitch for the only first Master in the list
* and do nothing for the other Masters
*
* So, set the SYNCGO bit only if CMDSYNC bit is set for any Master.
*/
if (!(sync_reg & SDW_SHIM_SYNC_CMDSYNC_MASK)) {
ret = 0;
goto unlock;
}
ret = intel_shim_sync_go_unlocked(sdw);
unlock:
mutex_unlock(sdw->link_res->shim_lock);
if (ret < 0)
dev_err(sdw->cdns.dev, "Post bank switch failed: %d\n", ret);
return ret;
}
/*
* DAI routines
*/
static int intel_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
struct sdw_intel *sdw = cdns_to_intel(cdns);
struct sdw_cdns_dai_runtime *dai_runtime;
struct sdw_cdns_pdi *pdi;
struct sdw_stream_config sconfig;
struct sdw_port_config *pconfig;
int ch, dir;
int ret;
dai_runtime = cdns->dai_runtime_array[dai->id];
if (!dai_runtime)
return -EIO;
ch = params_channels(params);
if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
dir = SDW_DATA_DIR_RX;
else
dir = SDW_DATA_DIR_TX;
pdi = sdw_cdns_alloc_pdi(cdns, &cdns->pcm, ch, dir, dai->id);
if (!pdi) {
ret = -EINVAL;
goto error;
}
/* do run-time configurations for SHIM, ALH and PDI/PORT */
intel_pdi_shim_configure(sdw, pdi);
intel_pdi_alh_configure(sdw, pdi);
sdw_cdns_config_stream(cdns, ch, dir, pdi);
/* store pdi and hw_params, may be needed in prepare step */
dai_runtime->paused = false;
dai_runtime->suspended = false;
dai_runtime->pdi = pdi;
dai_runtime->hw_params = params;
/* Inform DSP about PDI stream number */
ret = intel_params_stream(sdw, substream->stream, dai, params,
sdw->instance,
pdi->intel_alh_id);
if (ret)
goto error;
sconfig.direction = dir;
sconfig.ch_count = ch;
sconfig.frame_rate = params_rate(params);
sconfig.type = dai_runtime->stream_type;
sconfig.bps = snd_pcm_format_width(params_format(params));
/* Port configuration */
pconfig = kzalloc(sizeof(*pconfig), GFP_KERNEL);
if (!pconfig) {
ret = -ENOMEM;
goto error;
}
pconfig->num = pdi->num;
pconfig->ch_mask = (1 << ch) - 1;
ret = sdw_stream_add_master(&cdns->bus, &sconfig,
pconfig, 1, dai_runtime->stream);
if (ret)
dev_err(cdns->dev, "add master to stream failed:%d\n", ret);
kfree(pconfig);
error:
return ret;
}
static int intel_prepare(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
struct sdw_intel *sdw = cdns_to_intel(cdns);
struct sdw_cdns_dai_runtime *dai_runtime;
int ch, dir;
int ret = 0;
dai_runtime = cdns->dai_runtime_array[dai->id];
if (!dai_runtime) {
dev_err(dai->dev, "failed to get dai runtime in %s\n",
__func__);
return -EIO;
}
if (dai_runtime->suspended) {
dai_runtime->suspended = false;
/*
* .prepare() is called after system resume, where we
* need to reinitialize the SHIM/ALH/Cadence IP.
* .prepare() is also called to deal with underflows,
* but in those cases we cannot touch ALH/SHIM
* registers
*/
/* configure stream */
ch = params_channels(dai_runtime->hw_params);
if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
dir = SDW_DATA_DIR_RX;
else
dir = SDW_DATA_DIR_TX;
intel_pdi_shim_configure(sdw, dai_runtime->pdi);
intel_pdi_alh_configure(sdw, dai_runtime->pdi);
sdw_cdns_config_stream(cdns, ch, dir, dai_runtime->pdi);
/* Inform DSP about PDI stream number */
ret = intel_params_stream(sdw, substream->stream, dai,
dai_runtime->hw_params,
sdw->instance,
dai_runtime->pdi->intel_alh_id);
}
return ret;
}
static int
intel_hw_free(struct snd_pcm_substream *substream, struct snd_soc_dai *dai)
{
struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
struct sdw_intel *sdw = cdns_to_intel(cdns);
struct sdw_cdns_dai_runtime *dai_runtime;
int ret;
dai_runtime = cdns->dai_runtime_array[dai->id];
if (!dai_runtime)
return -EIO;
/*
* The sdw stream state will transition to RELEASED when stream->
* master_list is empty. So the stream state will transition to
* DEPREPARED for the first cpu-dai and to RELEASED for the last
* cpu-dai.
*/
ret = sdw_stream_remove_master(&cdns->bus, dai_runtime->stream);
if (ret < 0) {
dev_err(dai->dev, "remove master from stream %s failed: %d\n",
dai_runtime->stream->name, ret);
return ret;
}
ret = intel_free_stream(sdw, substream->stream, dai, sdw->instance);
if (ret < 0) {
dev_err(dai->dev, "intel_free_stream: failed %d\n", ret);
return ret;
}
dai_runtime->hw_params = NULL;
dai_runtime->pdi = NULL;
return 0;
}
static int intel_pcm_set_sdw_stream(struct snd_soc_dai *dai,
void *stream, int direction)
{
return cdns_set_sdw_stream(dai, stream, direction);
}
static void *intel_get_sdw_stream(struct snd_soc_dai *dai,
int direction)
{
struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
struct sdw_cdns_dai_runtime *dai_runtime;
dai_runtime = cdns->dai_runtime_array[dai->id];
if (!dai_runtime)
return ERR_PTR(-EINVAL);
return dai_runtime->stream;
}
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
static int intel_trigger(struct snd_pcm_substream *substream, int cmd, struct snd_soc_dai *dai)
{
struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
struct sdw_intel *sdw = cdns_to_intel(cdns);
struct sdw_intel_link_res *res = sdw->link_res;
struct sdw_cdns_dai_runtime *dai_runtime;
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
int ret = 0;
/*
* The .trigger callback is used to send required IPC to audio
* firmware. The .free_stream callback will still be called
* by intel_free_stream() in the TRIGGER_SUSPEND case.
*/
if (res->ops && res->ops->trigger)
res->ops->trigger(dai, cmd, substream->stream);
dai_runtime = cdns->dai_runtime_array[dai->id];
if (!dai_runtime) {
dev_err(dai->dev, "failed to get dai runtime in %s\n",
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
__func__);
return -EIO;
}
switch (cmd) {
case SNDRV_PCM_TRIGGER_SUSPEND:
/*
* The .prepare callback is used to deal with xruns and resume operations.
* In the case of xruns, the DMAs and SHIM registers cannot be touched,
* but for resume operations the DMAs and SHIM registers need to be initialized.
* the .trigger callback is used to track the suspend case only.
*/
dai_runtime->suspended = true;
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
ret = intel_free_stream(sdw, substream->stream, dai, sdw->instance);
break;
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
dai_runtime->paused = true;
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
break;
case SNDRV_PCM_TRIGGER_STOP:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
dai_runtime->paused = false;
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
break;
default:
break;
}
return ret;
}
soundwire: intel: use pm_runtime_resume() on component probe During the card registration, transactions on the SoundWire bus can be initiated. If the ALSA card is registered after the bus suspends, timeouts can be seen while reading/writing codec registers. This is extremely easy to reproduce in driver bind/unbind tests. In an initial experiment, the ASoC soc-component.c code was modified to initiate a pm_runtime resume on a component probe. The results showed this was too invasive. Instead this patch suggests resuming the SoundWire component only. Because of the parent-child hierarchy enforced by the pm_runtime framework, it can be argued that the codec component probe should be enough to resume all necessary devices, and indeed the same resume will be applied to SoundWire codecs used on Intel platforms. Calling pm_runtime_resume() on both the Intel and codec sides has the benefit of resuming the bus without assuming any order during the card registration. The first component on a dailink to be probed will resume the bus. In addition, if a codec driver did not implement this transition, the Intel component would still resume the bus and avoid timeouts on card registration. BugLink: https://github.com/thesofproject/linux/issues/3651 Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220621225641.221170-4-pierre-louis.bossart@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-06-21 22:56:40 +00:00
static int intel_component_probe(struct snd_soc_component *component)
{
int ret;
/*
* make sure the device is pm_runtime_active before initiating
* bus transactions during the card registration.
* We use pm_runtime_resume() here, without taking a reference
* and releasing it immediately.
*/
ret = pm_runtime_resume(component->dev);
if (ret < 0 && ret != -EACCES)
return ret;
return 0;
}
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
static int intel_component_dais_suspend(struct snd_soc_component *component)
{
struct snd_soc_dai *dai;
/*
* In the corner case where a SUSPEND happens during a PAUSE, the ALSA core
* does not throw the TRIGGER_SUSPEND. This leaves the DAIs in an unbalanced state.
* Since the component suspend is called last, we can trap this corner case
* and force the DAIs to release their resources.
*/
for_each_component_dais(component, dai) {
struct sdw_cdns *cdns = snd_soc_dai_get_drvdata(dai);
struct sdw_intel *sdw = cdns_to_intel(cdns);
struct sdw_cdns_dai_runtime *dai_runtime;
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
int ret;
dai_runtime = cdns->dai_runtime_array[dai->id];
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
if (!dai_runtime)
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
continue;
if (dai_runtime->suspended)
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
continue;
if (dai_runtime->paused) {
dai_runtime->suspended = true;
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
ret = intel_free_stream(sdw, dai_runtime->direction, dai, sdw->instance);
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
if (ret < 0)
return ret;
}
}
return 0;
}
static const struct snd_soc_dai_ops intel_pcm_dai_ops = {
.hw_params = intel_hw_params,
.prepare = intel_prepare,
.hw_free = intel_hw_free,
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:30 +00:00
.trigger = intel_trigger,
ASoC/SoundWire: dai: expand 'stream' concept beyond SoundWire The HDAudio ASoC support relies on the set_tdm_slots() helper to store the HDaudio stream tag in the tx_mask. This only works because of the pre-existing order in soc-pcm.c, where the hw_params() is handled for codec_dais *before* cpu_dais. When the order is reversed, the stream_tag is used as a mask in the codec fixup functions: /* fixup params based on TDM slot masks */ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && codec_dai->tx_mask) soc_pcm_codec_params_fixup(&codec_params, codec_dai->tx_mask); As a result of this confusion, the codec_params_fixup() ends-up generating bad channel masks, depending on what stream_tag was allocated. We could add a flag to state that the tx_mask is really not a mask, but it would be quite ugly to persist in overloading concepts. Instead, this patch suggests a more generic get/set 'stream' API based on the existing model for SoundWire. We can expand the concept to store 'stream' opaque information that is specific to different DAI types. In the case of HDAudio DAIs, we only need to store a stream tag as an unsigned char pointer. The TDM rx_ and tx_masks should really only be used to store masks. Rename get_sdw_stream/set_sdw_stream callbacks and helpers as get_stream/set_stream. No functionality change beyond the rename. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 02:10:31 +00:00
.set_stream = intel_pcm_set_sdw_stream,
.get_stream = intel_get_sdw_stream,
};
static const struct snd_soc_component_driver dai_component = {
.name = "soundwire",
sound updates for 6.0-rc1 As diffstat shows, we've had lots of developments in a wide range at this time; the majority of changes are about ASoC, including subsystem-wide cleanups, continued SOF / Intel updates and a bunch of new drivers (as usual), while there have been some significant (but almost invisible) improvements in ALSA core side, too. Below are some highlights: Core: - Faster lookups of control elements with Xarray; normal user won't notice, but on the devices with tons of control elements, it can be visibly faster - Support for input validation for controls; this will harden for badly written drivers in general with a slight overhead - Deferred async signal handling for working around the potential deadlocks - Cleanup / refactoring raw MIDI locking code ASoC: - Restructing of the set_fmt() callbacks for making things clearer in situations like CODEC to CODEC links - Clean up and modernizing the DAI naming scheme setups - Merge of more of the Intel AVS driver stack, including some board integrations - New version 4 mechanism for communication with SOF DSPs - Suppoort for dynamically selecting the PLL to use at runtime on i.MX platforms - Improvements for CODEC to CODEC support in the generic cards - Support for AMD Jadeite and various machines, AMD RPL, Intel MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments TAS2780 HD- and USB-audio: - Continued improvement for CS35L41 (sub)codec support - More quirks for various devices (HP, Lenovo, Dell, Clevo) -----BEGIN PGP SIGNATURE----- iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmLr5bcOHHRpd2FpQHN1 c2UuZGUACgkQLtJE4w1nLE93IQ/+OleeiGv7C487QN5MrBCkdFnSAiXsXDArcMgo Gt6XLubH54et1tqi2ms4gRQOqr4HiBelERuqmaCLMZfEgVDc0VhJnf2jjhluYq9+ o9+kcYKul6qTZeNZLPjEX8pBvDe7HzOl7yep++ZnKeH6DAKNQQLDjVuOcQU/BXdY kL8vYrLI3zfqj/pCePb5xpkBx4XdCrE3TfiCr3tAHVg9MyvSGOJyWs02mEBqQRnc rlLmkjQVQyln/AGK4RAPMmrrFytktAvBjmIDyFL7kAzhdxe0ouNzTvdxESeojNJv CVo/p3hl/+0LYjpD2x9v2pQuifOfpjwSCy6f8jsaF366sMwR1D45h051prILsxAF 05D5AOwMCnnJdFQFxw3mIkoDva3/PRX8GFfHsXoz+efc5Ibp8ksNYVgAJ3D2TTtt 7nAYMn0dimVDtw2LHiKantgWAs/rOqD3hDzGxFj2sR662ahsHr8pT8csnJAGoBvW 7kgx7ZzFo/wSyZJqVqV7p4g6J79ScehRwhqoiwZau9Eo+PhuxZUKvm4RwGFh0Vvg GbiVRPfLV4xQd/pDin6qRX1M7cgPc62qGLkhQHAzrX6H5ipwIbQrpyDGLjwdSEp8 XcQmzCG1zGOvb9A8BY1VBOQXxZRTqN58XujbZ6hsms7Uw8sqagxpYLA/e1bvt1E1 RQoHQRw= =1n0/ -----END PGP SIGNATURE----- Merge tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound updates from Takashi Iwai: "As the diffstat shows, we've had lots of developments in a wide range at this time; the majority of changes are about ASoC, including subsystem-wide cleanups, continued SOF / Intel updates and a bunch of new drivers (as usual), while there have been some significant (but almost invisible) improvements in ALSA core side, too. Below are some highlights: Core: - Faster lookups of control elements with Xarray; normal user won't notice, but on the devices with tons of control elements, it can be visibly faster - Support for input validation for controls; this will harden for badly written drivers in general with a slight overhead - Deferred async signal handling for working around the potential deadlocks - Cleanup / refactoring raw MIDI locking code ASoC: - Restructing of the set_fmt() callbacks for making things clearer in situations like CODEC to CODEC links - Clean up and modernizing the DAI naming scheme setups - Merge of more of the Intel AVS driver stack, including some board integrations - New version 4 mechanism for communication with SOF DSPs - Suppoort for dynamically selecting the PLL to use at runtime on i.MX platforms - Improvements for CODEC to CODEC support in the generic cards - Support for AMD Jadeite and various machines, AMD RPL, Intel MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments TAS2780 HD- and USB-audio: - Continued improvement for CS35L41 (sub)codec support - More quirks for various devices (HP, Lenovo, Dell, Clevo)" * tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits) ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx ALSA: line6: Replace sprintf() with sysfs_emit() ALSA: hda: Replace sprintf() with sysfs_emit() ALSA: pcm: Replace sprintf() with sysfs_emit() ALSA: core: Replace scnprintf() with sysfs_emit() ALSA: control-led: Replace sprintf() with sysfs_emit() ALSA: aoa: Replace sprintf() with sysfs_emit() ALSA: ac97: Replace sprintf() with sysfs_emit() ALSA: hda/realtek: Add quirk for Clevo NV45PZ ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7 ALSA: control: Use deferred fasync helper ALSA: pcm: Use deferred fasync helper ALSA: timer: Use deferred fasync helper ALSA: core: Add async signal helpers ASoC: q6asm: use kcalloc() instead of kzalloc() ACPI: scan: Add CLSA0101 Laptop Support ALSA: hda: cs35l41: Support CLSA0101 ALSA: hda: cs35l41: Use the CS35L41 HDA internal define ASoC: dt-bindings: use spi-peripheral-props.yaml ASoC: codecs: va-macro: use fsgen as clock ...
2022-08-06 17:19:51 +00:00
.probe = intel_component_probe,
.suspend = intel_component_dais_suspend,
.legacy_dai_naming = 1,
};
static int intel_create_dai(struct sdw_cdns *cdns,
struct snd_soc_dai_driver *dais,
enum intel_pdi_type type,
u32 num, u32 off, u32 max_ch)
{
int i;
if (num == 0)
return 0;
for (i = off; i < (off + num); i++) {
dais[i].name = devm_kasprintf(cdns->dev, GFP_KERNEL,
"SDW%d Pin%d",
cdns->instance, i);
if (!dais[i].name)
return -ENOMEM;
if (type == INTEL_PDI_BD || type == INTEL_PDI_OUT) {
dais[i].playback.channels_min = 1;
dais[i].playback.channels_max = max_ch;
}
if (type == INTEL_PDI_BD || type == INTEL_PDI_IN) {
dais[i].capture.channels_min = 1;
dais[i].capture.channels_max = max_ch;
}
dais[i].ops = &intel_pcm_dai_ops;
}
return 0;
}
static int intel_register_dai(struct sdw_intel *sdw)
{
struct sdw_cdns_dai_runtime **dai_runtime_array;
struct sdw_cdns_stream_config config;
struct sdw_cdns *cdns = &sdw->cdns;
struct sdw_cdns_streams *stream;
struct snd_soc_dai_driver *dais;
int num_dai, ret, off = 0;
/* Read the PDI config and initialize cadence PDI */
intel_pdi_init(sdw, &config);
ret = sdw_cdns_pdi_init(cdns, config);
if (ret)
return ret;
intel_pdi_stream_ch_update(sdw, &sdw->cdns.pcm);
/* DAIs are created based on total number of PDIs supported */
num_dai = cdns->pcm.num_pdi;
dai_runtime_array = devm_kcalloc(cdns->dev, num_dai,
sizeof(struct sdw_cdns_dai_runtime *),
GFP_KERNEL);
if (!dai_runtime_array)
return -ENOMEM;
cdns->dai_runtime_array = dai_runtime_array;
dais = devm_kcalloc(cdns->dev, num_dai, sizeof(*dais), GFP_KERNEL);
if (!dais)
return -ENOMEM;
/* Create PCM DAIs */
stream = &cdns->pcm;
ret = intel_create_dai(cdns, dais, INTEL_PDI_IN, cdns->pcm.num_in,
off, stream->num_ch_in);
if (ret)
return ret;
off += cdns->pcm.num_in;
ret = intel_create_dai(cdns, dais, INTEL_PDI_OUT, cdns->pcm.num_out,
off, stream->num_ch_out);
if (ret)
return ret;
off += cdns->pcm.num_out;
ret = intel_create_dai(cdns, dais, INTEL_PDI_BD, cdns->pcm.num_bd,
off, stream->num_ch_bd);
if (ret)
return ret;
return devm_snd_soc_register_component(cdns->dev, &dai_component,
dais, num_dai);
}
static int intel_start_bus(struct sdw_intel *sdw)
{
struct device *dev = sdw->cdns.dev;
struct sdw_cdns *cdns = &sdw->cdns;
struct sdw_bus *bus = &cdns->bus;
int ret;
ret = sdw_cdns_enable_interrupt(cdns, true);
if (ret < 0) {
dev_err(dev, "%s: cannot enable interrupts: %d\n", __func__, ret);
return ret;
}
/*
* follow recommended programming flows to avoid timeouts when
* gsync is enabled
*/
if (bus->multi_link)
intel_shim_sync_arm(sdw);
ret = sdw_cdns_init(cdns);
if (ret < 0) {
dev_err(dev, "%s: unable to initialize Cadence IP: %d\n", __func__, ret);
goto err_interrupt;
}
ret = sdw_cdns_exit_reset(cdns);
if (ret < 0) {
dev_err(dev, "%s: unable to exit bus reset sequence: %d\n", __func__, ret);
goto err_interrupt;
}
if (bus->multi_link) {
ret = intel_shim_sync_go(sdw);
if (ret < 0) {
dev_err(dev, "%s: sync go failed: %d\n", __func__, ret);
goto err_interrupt;
}
}
sdw_cdns_check_self_clearing_bits(cdns, __func__,
true, INTEL_MASTER_RESET_ITERATIONS);
return 0;
err_interrupt:
sdw_cdns_enable_interrupt(cdns, false);
return ret;
}
static int intel_start_bus_after_reset(struct sdw_intel *sdw)
{
struct device *dev = sdw->cdns.dev;
struct sdw_cdns *cdns = &sdw->cdns;
struct sdw_bus *bus = &cdns->bus;
bool clock_stop0;
int status;
int ret;
/*
* An exception condition occurs for the CLK_STOP_BUS_RESET
* case if one or more masters remain active. In this condition,
* all the masters are powered on for they are in the same power
* domain. Master can preserve its context for clock stop0, so
* there is no need to clear slave status and reset bus.
*/
clock_stop0 = sdw_cdns_is_clock_stop(&sdw->cdns);
if (!clock_stop0) {
/*
* make sure all Slaves are tagged as UNATTACHED and
* provide reason for reinitialization
*/
status = SDW_UNATTACH_REQUEST_MASTER_RESET;
sdw_clear_slave_status(bus, status);
ret = sdw_cdns_enable_interrupt(cdns, true);
if (ret < 0) {
dev_err(dev, "cannot enable interrupts during resume\n");
return ret;
}
/*
* follow recommended programming flows to avoid
* timeouts when gsync is enabled
*/
if (bus->multi_link)
intel_shim_sync_arm(sdw);
/*
* Re-initialize the IP since it was powered-off
*/
sdw_cdns_init(&sdw->cdns);
} else {
ret = sdw_cdns_enable_interrupt(cdns, true);
if (ret < 0) {
dev_err(dev, "cannot enable interrupts during resume\n");
return ret;
}
}
ret = sdw_cdns_clock_restart(cdns, !clock_stop0);
if (ret < 0) {
dev_err(dev, "unable to restart clock during resume\n");
goto err_interrupt;
}
if (!clock_stop0) {
ret = sdw_cdns_exit_reset(cdns);
if (ret < 0) {
dev_err(dev, "unable to exit bus reset sequence during resume\n");
goto err_interrupt;
}
if (bus->multi_link) {
ret = intel_shim_sync_go(sdw);
if (ret < 0) {
dev_err(sdw->cdns.dev, "sync go failed during resume\n");
goto err_interrupt;
}
}
}
sdw_cdns_check_self_clearing_bits(cdns, __func__, true, INTEL_MASTER_RESET_ITERATIONS);
return 0;
err_interrupt:
sdw_cdns_enable_interrupt(cdns, false);
return ret;
}
static void intel_check_clock_stop(struct sdw_intel *sdw)
{
struct device *dev = sdw->cdns.dev;
bool clock_stop0;
clock_stop0 = sdw_cdns_is_clock_stop(&sdw->cdns);
if (!clock_stop0)
dev_err(dev, "%s: invalid configuration, clock was not stopped\n", __func__);
}
static int intel_start_bus_after_clock_stop(struct sdw_intel *sdw)
{
struct device *dev = sdw->cdns.dev;
struct sdw_cdns *cdns = &sdw->cdns;
int ret;
ret = sdw_cdns_enable_interrupt(cdns, true);
if (ret < 0) {
dev_err(dev, "%s: cannot enable interrupts: %d\n", __func__, ret);
return ret;
}
ret = sdw_cdns_clock_restart(cdns, false);
if (ret < 0) {
dev_err(dev, "%s: unable to restart clock: %d\n", __func__, ret);
sdw_cdns_enable_interrupt(cdns, false);
return ret;
}
sdw_cdns_check_self_clearing_bits(cdns, "intel_resume_runtime no_quirks",
true, INTEL_MASTER_RESET_ITERATIONS);
return 0;
}
static int intel_stop_bus(struct sdw_intel *sdw, bool clock_stop)
{
struct device *dev = sdw->cdns.dev;
struct sdw_cdns *cdns = &sdw->cdns;
bool wake_enable = false;
int ret;
if (clock_stop) {
ret = sdw_cdns_clock_stop(cdns, true);
if (ret < 0)
dev_err(dev, "%s: cannot stop clock: %d\n", __func__, ret);
else
wake_enable = true;
}
ret = sdw_cdns_enable_interrupt(cdns, false);
if (ret < 0) {
dev_err(dev, "%s: cannot disable interrupts: %d\n", __func__, ret);
return ret;
}
ret = intel_link_power_down(sdw);
if (ret) {
dev_err(dev, "%s: Link power down failed: %d\n", __func__, ret);
return ret;
}
intel_shim_wake(sdw, wake_enable);
return 0;
}
const struct sdw_intel_hw_ops sdw_intel_cnl_hw_ops = {
.debugfs_init = intel_debugfs_init,
.debugfs_exit = intel_debugfs_exit,
.register_dai = intel_register_dai,
.check_clock_stop = intel_check_clock_stop,
.start_bus = intel_start_bus,
.start_bus_after_reset = intel_start_bus_after_reset,
.start_bus_after_clock_stop = intel_start_bus_after_clock_stop,
.stop_bus = intel_stop_bus,
.link_power_up = intel_link_power_up,
.link_power_down = intel_link_power_down,
.shim_check_wake = intel_shim_check_wake,
.shim_wake = intel_shim_wake,
.pre_bank_switch = intel_pre_bank_switch,
.post_bank_switch = intel_post_bank_switch,
};
EXPORT_SYMBOL_NS(sdw_intel_cnl_hw_ops, SOUNDWIRE_INTEL);