linux/mm/userfaultfd.c

845 lines
21 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* mm/userfaultfd.c
*
* Copyright (C) 2015 Red Hat, Inc.
*/
#include <linux/mm.h>
#include <linux/sched/signal.h>
#include <linux/pagemap.h>
#include <linux/rmap.h>
#include <linux/swap.h>
#include <linux/swapops.h>
#include <linux/userfaultfd_k.h>
#include <linux/mmu_notifier.h>
#include <linux/hugetlb.h>
#include <linux/shmem_fs.h>
#include <asm/tlbflush.h>
mm/mprotect: use mmu_gather Patch series "mm/mprotect: avoid unnecessary TLB flushes", v6. This patchset is intended to remove unnecessary TLB flushes during mprotect() syscalls. Once this patch-set make it through, similar and further optimizations for MADV_COLD and userfaultfd would be possible. Basically, there are 3 optimizations in this patch-set: 1. Use TLB batching infrastructure to batch flushes across VMAs and do better/fewer flushes. This would also be handy for later userfaultfd enhancements. 2. Avoid unnecessary TLB flushes. This optimization is the one that provides most of the performance benefits. Unlike previous versions, we now only avoid flushes that would not result in spurious page-faults. 3. Avoiding TLB flushes on change_huge_pmd() that are only needed to prevent the A/D bits from changing. Andrew asked for some benchmark numbers. I do not have an easy determinate macrobenchmark in which it is easy to show benefit. I therefore ran a microbenchmark: a loop that does the following on anonymous memory, just as a sanity check to see that time is saved by avoiding TLB flushes. The loop goes: mprotect(p, PAGE_SIZE, PROT_READ) mprotect(p, PAGE_SIZE, PROT_READ|PROT_WRITE) *p = 0; // make the page writable The test was run in KVM guest with 1 or 2 threads (the second thread was busy-looping). I measured the time (cycles) of each operation: 1 thread 2 threads mmots +patch mmots +patch PROT_READ 3494 2725 (-22%) 8630 7788 (-10%) PROT_READ|WRITE 3952 2724 (-31%) 9075 2865 (-68%) [ mmots = v5.17-rc6-mmots-2022-03-06-20-38 ] The exact numbers are really meaningless, but the benefit is clear. There are 2 interesting results though. (1) PROT_READ is cheaper, while one can expect it not to be affected. This is presumably due to TLB miss that is saved (2) Without memory access (*p = 0), the speedup of the patch is even greater. In that scenario mprotect(PROT_READ) also avoids the TLB flush. As a result both operations on the patched kernel take roughly ~1500 cycles (with either 1 or 2 threads), whereas on mmotm their cost is as high as presented in the table. This patch (of 3): change_pXX_range() currently does not use mmu_gather, but instead implements its own deferred TLB flushes scheme. This both complicates the code, as developers need to be aware of different invalidation schemes, and prevents opportunities to avoid TLB flushes or perform them in finer granularity. The use of mmu_gather for modified PTEs has benefits in various scenarios even if pages are not released. For instance, if only a single page needs to be flushed out of a range of many pages, only that page would be flushed. If a THP page is flushed, on x86 a single TLB invlpg instruction can be used instead of 512 instructions (or a full TLB flush, which would Linux would actually use by default). mprotect() over multiple VMAs requires a single flush. Use mmu_gather in change_pXX_range(). As the pages are not released, only record the flushed range using tlb_flush_pXX_range(). Handle THP similarly and get rid of flush_cache_range() which becomes redundant since tlb_start_vma() calls it when needed. Link: https://lkml.kernel.org/r/20220401180821.1986781-1-namit@vmware.com Link: https://lkml.kernel.org/r/20220401180821.1986781-2-namit@vmware.com Signed-off-by: Nadav Amit <namit@vmware.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Peter Xu <peterx@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Cc: Yu Zhao <yuzhao@google.com> Cc: Nick Piggin <npiggin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-05-10 01:20:50 +00:00
#include <asm/tlb.h>
#include "internal.h"
static __always_inline
struct vm_area_struct *find_dst_vma(struct mm_struct *dst_mm,
unsigned long dst_start,
unsigned long len)
{
/*
* Make sure that the dst range is both valid and fully within a
* single existing vma.
*/
struct vm_area_struct *dst_vma;
dst_vma = find_vma(dst_mm, dst_start);
if (!range_in_vma(dst_vma, dst_start, dst_start + len))
return NULL;
/*
* Check the vma is registered in uffd, this is required to
* enforce the VM_MAYWRITE check done at uffd registration
* time.
*/
if (!dst_vma->vm_userfaultfd_ctx.ctx)
return NULL;
return dst_vma;
}
mm: userfaultfd: extract file size check out into a helper This code is already duplicated twice, and UFFDIO_POISON will do the same check a third time. So, it's worth extracting into a helper to save repetitive lines of code. Link: https://lkml.kernel.org/r/20230707215540.2324998-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:35 +00:00
/* Check if dst_addr is outside of file's size. Must be called with ptl held. */
static bool mfill_file_over_size(struct vm_area_struct *dst_vma,
unsigned long dst_addr)
{
struct inode *inode;
pgoff_t offset, max_off;
if (!dst_vma->vm_file)
return false;
inode = dst_vma->vm_file->f_inode;
offset = linear_page_index(dst_vma, dst_addr);
max_off = DIV_ROUND_UP(i_size_read(inode), PAGE_SIZE);
return offset >= max_off;
}
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
/*
* Install PTEs, to map dst_addr (within dst_vma) to page.
*
userfaultfd/shmem: modify shmem_mfill_atomic_pte to use install_pte() In a previous commit, we added the mfill_atomic_install_pte() helper. This helper does the job of setting up PTEs for an existing page, to map it into a given VMA. It deals with both the anon and shmem cases, as well as the shared and private cases. In other words, shmem_mfill_atomic_pte() duplicates a case it already handles. So, expose it, and let shmem_mfill_atomic_pte() use it directly, to reduce code duplication. This requires that we refactor shmem_mfill_atomic_pte() a bit: Instead of doing accounting (shmem_recalc_inode() et al) part-way through the PTE setup, do it afterward. This frees up mfill_atomic_install_pte() from having to care about this accounting, and means we don't need to e.g. shmem_uncharge() in the error path. A side effect is this switches shmem_mfill_atomic_pte() to use lru_cache_add_inactive_or_unevictable() instead of just lru_cache_add(). This wrapper does some extra accounting in an exceptional case, if appropriate, so it's actually the more correct thing to use. Link: https://lkml.kernel.org/r/20210503180737.2487560-7-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:31 +00:00
* This function handles both MCOPY_ATOMIC_NORMAL and _CONTINUE for both shmem
* and anon, and for both shared and private VMAs.
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
*/
int mfill_atomic_install_pte(pmd_t *dst_pmd,
userfaultfd/shmem: modify shmem_mfill_atomic_pte to use install_pte() In a previous commit, we added the mfill_atomic_install_pte() helper. This helper does the job of setting up PTEs for an existing page, to map it into a given VMA. It deals with both the anon and shmem cases, as well as the shared and private cases. In other words, shmem_mfill_atomic_pte() duplicates a case it already handles. So, expose it, and let shmem_mfill_atomic_pte() use it directly, to reduce code duplication. This requires that we refactor shmem_mfill_atomic_pte() a bit: Instead of doing accounting (shmem_recalc_inode() et al) part-way through the PTE setup, do it afterward. This frees up mfill_atomic_install_pte() from having to care about this accounting, and means we don't need to e.g. shmem_uncharge() in the error path. A side effect is this switches shmem_mfill_atomic_pte() to use lru_cache_add_inactive_or_unevictable() instead of just lru_cache_add(). This wrapper does some extra accounting in an exceptional case, if appropriate, so it's actually the more correct thing to use. Link: https://lkml.kernel.org/r/20210503180737.2487560-7-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:31 +00:00
struct vm_area_struct *dst_vma,
unsigned long dst_addr, struct page *page,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
bool newly_allocated, uffd_flags_t flags)
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
{
int ret;
struct mm_struct *dst_mm = dst_vma->vm_mm;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
pte_t _dst_pte, *dst_pte;
bool writable = dst_vma->vm_flags & VM_WRITE;
bool vm_shared = dst_vma->vm_flags & VM_SHARED;
bool page_in_cache = page_mapping(page);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
spinlock_t *ptl;
struct folio *folio;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
_dst_pte = mk_pte(page, dst_vma->vm_page_prot);
mm/shmem: unconditionally set pte dirty in mfill_atomic_install_pte Patch series "mm: A few cleanup patches around zap, shmem and uffd", v4. IMHO all of them are very nice cleanups to existing code already, they're all small and self-contained. They'll be needed by uffd-wp coming series. This patch (of 4): It was conditionally done previously, as there's one shmem special case that we use SetPageDirty() instead. However that's not necessary and it should be easier and cleaner to do it unconditionally in mfill_atomic_install_pte(). The most recent discussion about this is here, where Hugh explained the history of SetPageDirty() and why it's possible that it's not required at all: https://lore.kernel.org/lkml/alpine.LSU.2.11.2104121657050.1097@eggly.anvils/ Currently mfill_atomic_install_pte() has three callers: 1. shmem_mfill_atomic_pte 2. mcopy_atomic_pte 3. mcontinue_atomic_pte After the change: case (1) should have its SetPageDirty replaced by the dirty bit on pte (so we unify them together, finally), case (2) should have no functional change at all as it has page_in_cache==false, case (3) may add a dirty bit to the pte. However since case (3) is UFFDIO_CONTINUE for shmem, it's merely 100% sure the page is dirty after all because UFFDIO_CONTINUE normally requires another process to modify the page cache and kick the faulted thread, so should not make a real difference either. This should make it much easier to follow on which case will set dirty for uffd, as we'll simply set it all now for all uffd related ioctls. Meanwhile, no special handling of SetPageDirty() if there's no need. Link: https://lkml.kernel.org/r/20210915181456.10739-1-peterx@redhat.com Link: https://lkml.kernel.org/r/20210915181456.10739-2-peterx@redhat.com Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Axel Rasmussen <axelrasmussen@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Liam Howlett <liam.howlett@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Yang Shi <shy828301@gmail.com> Cc: David Hildenbrand <david@redhat.com> Cc: "Kirill A . Shutemov" <kirill@shutemov.name> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-05 20:38:24 +00:00
_dst_pte = pte_mkdirty(_dst_pte);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
if (page_in_cache && !vm_shared)
writable = false;
if (writable)
mm: Make pte_mkwrite() take a VMA The x86 Shadow stack feature includes a new type of memory called shadow stack. This shadow stack memory has some unusual properties, which requires some core mm changes to function properly. One of these unusual properties is that shadow stack memory is writable, but only in limited ways. These limits are applied via a specific PTE bit combination. Nevertheless, the memory is writable, and core mm code will need to apply the writable permissions in the typical paths that call pte_mkwrite(). Future patches will make pte_mkwrite() take a VMA, so that the x86 implementation of it can know whether to create regular writable or shadow stack mappings. But there are a couple of challenges to this. Modifying the signatures of each arch pte_mkwrite() implementation would be error prone because some are generated with macros and would need to be re-implemented. Also, some pte_mkwrite() callers operate on kernel memory without a VMA. So this can be done in a three step process. First pte_mkwrite() can be renamed to pte_mkwrite_novma() in each arch, with a generic pte_mkwrite() added that just calls pte_mkwrite_novma(). Next callers without a VMA can be moved to pte_mkwrite_novma(). And lastly, pte_mkwrite() and all callers can be changed to take/pass a VMA. Previous work pte_mkwrite() renamed pte_mkwrite_novma() and converted callers that don't have a VMA were to use pte_mkwrite_novma(). So now change pte_mkwrite() to take a VMA and change the remaining callers to pass a VMA. Apply the same changes for pmd_mkwrite(). No functional change. Suggested-by: David Hildenbrand <david@redhat.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org> Acked-by: David Hildenbrand <david@redhat.com> Link: https://lore.kernel.org/all/20230613001108.3040476-4-rick.p.edgecombe%40intel.com
2023-06-13 00:10:29 +00:00
_dst_pte = pte_mkwrite(_dst_pte, dst_vma);
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
if (flags & MFILL_ATOMIC_WP)
mm/uffd: always wr-protect pte in pte|pmd_mkuffd_wp() This patch is a cleanup to always wr-protect pte/pmd in mkuffd_wp paths. The reasons I still think this patch is worthwhile, are: (1) It is a cleanup already; diffstat tells. (2) It just feels natural after I thought about this, if the pte is uffd protected, let's remove the write bit no matter what it was. (2) Since x86 is the only arch that supports uffd-wp, it also redefines pte|pmd_mkuffd_wp() in that it should always contain removals of write bits. It means any future arch that want to implement uffd-wp should naturally follow this rule too. It's good to make it a default, even if with vm_page_prot changes on VM_UFFD_WP. (3) It covers more than vm_page_prot. So no chance of any potential future "accident" (like pte_mkdirty() sparc64 or loongarch, even though it just got its pte_mkdirty fixed <1 month ago). It'll be fairly clear when reading the code too that we don't worry anything before a pte_mkuffd_wp() on uncertainty of the write bit. We may call pte_wrprotect() one more time in some paths (e.g. thp split), but that should be fully local bitop instruction so the overhead should be negligible. Although this patch should logically also fix all the known issues on uffd-wp too recently on page migration (not for numa hint recovery - that may need another explcit pte_wrprotect), but this is not the plan for that fix. So no fixes, and stable doesn't need this. Link: https://lkml.kernel.org/r/20221214201533.1774616-1-peterx@redhat.com Signed-off-by: Peter Xu <peterx@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Ives van Hoorne <ives@codesandbox.io> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Nadav Amit <nadav.amit@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-14 20:15:33 +00:00
_dst_pte = pte_mkuffd_wp(_dst_pte);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
mm/userfaultfd: allow pte_offset_map_lock() to fail mfill_atomic_install_pte() and mfill_atomic_pte_zeropage() treat failed pte_offset_map_lock() as -EAGAIN, which mfill_atomic() already returns to user for a similar race. Link: https://lkml.kernel.org/r/50cf3930-1bfa-4de9-a079-3da47b7ce17b@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 01:26:04 +00:00
ret = -EAGAIN;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
dst_pte = pte_offset_map_lock(dst_mm, dst_pmd, dst_addr, &ptl);
mm/userfaultfd: allow pte_offset_map_lock() to fail mfill_atomic_install_pte() and mfill_atomic_pte_zeropage() treat failed pte_offset_map_lock() as -EAGAIN, which mfill_atomic() already returns to user for a similar race. Link: https://lkml.kernel.org/r/50cf3930-1bfa-4de9-a079-3da47b7ce17b@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 01:26:04 +00:00
if (!dst_pte)
goto out;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
mm: userfaultfd: extract file size check out into a helper This code is already duplicated twice, and UFFDIO_POISON will do the same check a third time. So, it's worth extracting into a helper to save repetitive lines of code. Link: https://lkml.kernel.org/r/20230707215540.2324998-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:35 +00:00
if (mfill_file_over_size(dst_vma, dst_addr)) {
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
ret = -EFAULT;
mm: userfaultfd: extract file size check out into a helper This code is already duplicated twice, and UFFDIO_POISON will do the same check a third time. So, it's worth extracting into a helper to save repetitive lines of code. Link: https://lkml.kernel.org/r/20230707215540.2324998-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:35 +00:00
goto out_unlock;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
}
ret = -EEXIST;
/*
* We allow to overwrite a pte marker: consider when both MISSING|WP
* registered, we firstly wr-protect a none pte which has no page cache
* page backing it, then access the page.
*/
mm: ptep_get() conversion Convert all instances of direct pte_t* dereferencing to instead use ptep_get() helper. This means that by default, the accesses change from a C dereference to a READ_ONCE(). This is technically the correct thing to do since where pgtables are modified by HW (for access/dirty) they are volatile and therefore we should always ensure READ_ONCE() semantics. But more importantly, by always using the helper, it can be overridden by the architecture to fully encapsulate the contents of the pte. Arch code is deliberately not converted, as the arch code knows best. It is intended that arch code (arm64) will override the default with its own implementation that can (e.g.) hide certain bits from the core code, or determine young/dirty status by mixing in state from another source. Conversion was done using Coccinelle: ---- // $ make coccicheck \ // COCCI=ptepget.cocci \ // SPFLAGS="--include-headers" \ // MODE=patch virtual patch @ depends on patch @ pte_t *v; @@ - *v + ptep_get(v) ---- Then reviewed and hand-edited to avoid multiple unnecessary calls to ptep_get(), instead opting to store the result of a single call in a variable, where it is correct to do so. This aims to negate any cost of READ_ONCE() and will benefit arch-overrides that may be more complex. Included is a fix for an issue in an earlier version of this patch that was pointed out by kernel test robot. The issue arose because config MMU=n elides definition of the ptep helper functions, including ptep_get(). HUGETLB_PAGE=n configs still define a simple huge_ptep_clear_flush() for linking purposes, which dereferences the ptep. So when both configs are disabled, this caused a build error because ptep_get() is not defined. Fix by continuing to do a direct dereference when MMU=n. This is safe because for this config the arch code cannot be trying to virtualize the ptes because none of the ptep helpers are defined. Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/ Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: SeongJae Park <sj@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 15:15:45 +00:00
if (!pte_none_mostly(ptep_get(dst_pte)))
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
goto out_unlock;
folio = page_folio(page);
mm/munlock: rmap call mlock_vma_page() munlock_vma_page() Add vma argument to mlock_vma_page() and munlock_vma_page(), make them inline functions which check (vma->vm_flags & VM_LOCKED) before calling mlock_page() and munlock_page() in mm/mlock.c. Add bool compound to mlock_vma_page() and munlock_vma_page(): this is because we have understandable difficulty in accounting pte maps of THPs, and if passed a PageHead page, mlock_page() and munlock_page() cannot tell whether it's a pmd map to be counted or a pte map to be ignored. Add vma arg to page_add_file_rmap() and page_remove_rmap(), like the others, and use that to call mlock_vma_page() at the end of the page adds, and munlock_vma_page() at the end of page_remove_rmap() (end or beginning? unimportant, but end was easier for assertions in testing). No page lock is required (although almost all adds happen to hold it): delete the "Serialize with page migration" BUG_ON(!PageLocked(page))s. Certainly page lock did serialize with page migration, but I'm having difficulty explaining why that was ever important. Mlock accounting on THPs has been hard to define, differed between anon and file, involved PageDoubleMap in some places and not others, required clear_page_mlock() at some points. Keep it simple now: just count the pmds and ignore the ptes, there is no reason for ptes to undo pmd mlocks. page_add_new_anon_rmap() callers unchanged: they have long been calling lru_cache_add_inactive_or_unevictable(), which does its own VM_LOCKED handling (it also checks for not VM_SPECIAL: I think that's overcautious, and inconsistent with other checks, that mmap_region() already prevents VM_LOCKED on VM_SPECIAL; but haven't quite convinced myself to change it). Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
2022-02-15 02:26:39 +00:00
if (page_in_cache) {
/* Usually, cache pages are already added to LRU */
if (newly_allocated)
folio_add_lru(folio);
mm/munlock: rmap call mlock_vma_page() munlock_vma_page() Add vma argument to mlock_vma_page() and munlock_vma_page(), make them inline functions which check (vma->vm_flags & VM_LOCKED) before calling mlock_page() and munlock_page() in mm/mlock.c. Add bool compound to mlock_vma_page() and munlock_vma_page(): this is because we have understandable difficulty in accounting pte maps of THPs, and if passed a PageHead page, mlock_page() and munlock_page() cannot tell whether it's a pmd map to be counted or a pte map to be ignored. Add vma arg to page_add_file_rmap() and page_remove_rmap(), like the others, and use that to call mlock_vma_page() at the end of the page adds, and munlock_vma_page() at the end of page_remove_rmap() (end or beginning? unimportant, but end was easier for assertions in testing). No page lock is required (although almost all adds happen to hold it): delete the "Serialize with page migration" BUG_ON(!PageLocked(page))s. Certainly page lock did serialize with page migration, but I'm having difficulty explaining why that was ever important. Mlock accounting on THPs has been hard to define, differed between anon and file, involved PageDoubleMap in some places and not others, required clear_page_mlock() at some points. Keep it simple now: just count the pmds and ignore the ptes, there is no reason for ptes to undo pmd mlocks. page_add_new_anon_rmap() callers unchanged: they have long been calling lru_cache_add_inactive_or_unevictable(), which does its own VM_LOCKED handling (it also checks for not VM_SPECIAL: I think that's overcautious, and inconsistent with other checks, that mmap_region() already prevents VM_LOCKED on VM_SPECIAL; but haven't quite convinced myself to change it). Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
2022-02-15 02:26:39 +00:00
page_add_file_rmap(page, dst_vma, false);
} else {
mm/rmap: drop "compound" parameter from page_add_new_anon_rmap() New anonymous pages are always mapped natively: only THP/khugepaged code maps a new compound anonymous page and passes "true". Otherwise, we're just dealing with simple, non-compound pages. Let's give the interface clearer semantics and document these. Remove the PageTransCompound() sanity check from page_add_new_anon_rmap(). Link: https://lkml.kernel.org/r/20220428083441.37290-9-david@redhat.com Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: David Rientjes <rientjes@google.com> Cc: Don Dutile <ddutile@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Jann Horn <jannh@google.com> Cc: Jason Gunthorpe <jgg@nvidia.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Khalid Aziz <khalid.aziz@oracle.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Liang Zhang <zhangliang5@huawei.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Nadav Amit <namit@vmware.com> Cc: Oded Gabbay <oded.gabbay@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Pedro Demarchi Gomes <pedrodemargomes@gmail.com> Cc: Peter Xu <peterx@redhat.com> Cc: Rik van Riel <riel@surriel.com> Cc: Roman Gushchin <guro@fb.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-05-10 01:20:43 +00:00
page_add_new_anon_rmap(page, dst_vma, dst_addr);
folio_add_lru_vma(folio, dst_vma);
mm/munlock: rmap call mlock_vma_page() munlock_vma_page() Add vma argument to mlock_vma_page() and munlock_vma_page(), make them inline functions which check (vma->vm_flags & VM_LOCKED) before calling mlock_page() and munlock_page() in mm/mlock.c. Add bool compound to mlock_vma_page() and munlock_vma_page(): this is because we have understandable difficulty in accounting pte maps of THPs, and if passed a PageHead page, mlock_page() and munlock_page() cannot tell whether it's a pmd map to be counted or a pte map to be ignored. Add vma arg to page_add_file_rmap() and page_remove_rmap(), like the others, and use that to call mlock_vma_page() at the end of the page adds, and munlock_vma_page() at the end of page_remove_rmap() (end or beginning? unimportant, but end was easier for assertions in testing). No page lock is required (although almost all adds happen to hold it): delete the "Serialize with page migration" BUG_ON(!PageLocked(page))s. Certainly page lock did serialize with page migration, but I'm having difficulty explaining why that was ever important. Mlock accounting on THPs has been hard to define, differed between anon and file, involved PageDoubleMap in some places and not others, required clear_page_mlock() at some points. Keep it simple now: just count the pmds and ignore the ptes, there is no reason for ptes to undo pmd mlocks. page_add_new_anon_rmap() callers unchanged: they have long been calling lru_cache_add_inactive_or_unevictable(), which does its own VM_LOCKED handling (it also checks for not VM_SPECIAL: I think that's overcautious, and inconsistent with other checks, that mmap_region() already prevents VM_LOCKED on VM_SPECIAL; but haven't quite convinced myself to change it). Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
2022-02-15 02:26:39 +00:00
}
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
/*
* Must happen after rmap, as mm_counter() checks mapping (via
* PageAnon()), which is set by __page_set_anon_rmap().
*/
inc_mm_counter(dst_mm, mm_counter(page));
set_pte_at(dst_mm, dst_addr, dst_pte, _dst_pte);
/* No need to invalidate - it was non-present before */
update_mmu_cache(dst_vma, dst_addr, dst_pte);
ret = 0;
out_unlock:
pte_unmap_unlock(dst_pte, ptl);
mm/userfaultfd: allow pte_offset_map_lock() to fail mfill_atomic_install_pte() and mfill_atomic_pte_zeropage() treat failed pte_offset_map_lock() as -EAGAIN, which mfill_atomic() already returns to user for a similar race. Link: https://lkml.kernel.org/r/50cf3930-1bfa-4de9-a079-3da47b7ce17b@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 01:26:04 +00:00
out:
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
return ret;
}
static int mfill_atomic_pte_copy(pmd_t *dst_pmd,
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
struct vm_area_struct *dst_vma,
unsigned long dst_addr,
unsigned long src_addr,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
uffd_flags_t flags,
struct folio **foliop)
{
void *kaddr;
int ret;
struct folio *folio;
if (!*foliop) {
ret = -ENOMEM;
folio = vma_alloc_folio(GFP_HIGHUSER_MOVABLE, 0, dst_vma,
dst_addr, false);
if (!folio)
goto out;
kaddr = kmap_local_folio(folio, 0);
mm/userfaultfd: replace kmap/kmap_atomic() with kmap_local_page() kmap() and kmap_atomic() are being deprecated in favor of kmap_local_page() which is appropriate for any thread local context.[1] A recent locking bug report with userfaultfd showed that the conversion of the kmap_atomic()'s in those code flows requires care with regard to the prevention of deadlock.[2] git archaeology implied that the recursion may not be an actual bug.[3] However, depending on the implementation of the mmap_lock and the condition of the call there may still be a deadlock.[4] So this is not purely a lockdep issue. Considering a single threaded call stack there are 3 options. 1) Different mm's are in play (no issue) 2) Readlock implementation is recursive and same mm is in play (no issue) 3) Readlock implementation is _not_ recursive (issue) The mmap_lock is recursive so with a single thread there is no issue. However, Matthew pointed out a deadlock scenario when you consider additional process' and threads thusly. "The readlock implementation is only recursive if nobody else has taken a write lock. If you have a multithreaded process, one of the other threads can call mmap() and that will prevent recursion (due to fairness). Even if it's a different process that you're trying to acquire the mmap read lock on, you can still get into a deadly embrace. eg: process A thread 1 takes read lock on own mmap_lock process A thread 2 calls mmap, blocks taking write lock process B thread 1 takes page fault, read lock on own mmap lock process B thread 2 calls mmap, blocks taking write lock process A thread 1 blocks taking read lock on process B process B thread 1 blocks taking read lock on process A Now all four threads are blocked waiting for each other." Regardless using pagefault_disable() ensures that no matter what locking implementation is used a deadlock will not occur. Complete kmap conversion in userfaultfd by replacing the kmap() and kmap_atomic() calls with kmap_local_page(). When replacing the kmap_atomic() call ensure page faults continue to be disabled to support the correct fall back behavior and add a comment to inform future souls of the requirement. [1] https://lore.kernel.org/all/20220813220034.806698-1-ira.weiny@intel.com/ [2] https://lore.kernel.org/all/Y1Mh2S7fUGQ%2FiKFR@iweiny-desk3/ [3] https://lore.kernel.org/all/Y1MymJ%2FINb45AdaY@iweiny-desk3/ [4] https://lore.kernel.org/lkml/Y1bXBtGTCym77%2FoD@casper.infradead.org/ [ira.weiny@intel.com: v2] Link: https://lkml.kernel.org/r/20221025220136.2366143-1-ira.weiny@intel.com Link: https://lkml.kernel.org/r/20221024043452.1491677-1-ira.weiny@intel.com Signed-off-by: Ira Weiny <ira.weiny@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-10-24 04:34:52 +00:00
/*
* The read mmap_lock is held here. Despite the
* mmap_lock being read recursive a deadlock is still
* possible if a writer has taken a lock. For example:
*
* process A thread 1 takes read lock on own mmap_lock
* process A thread 2 calls mmap, blocks taking write lock
* process B thread 1 takes page fault, read lock on own mmap lock
* process B thread 2 calls mmap, blocks taking write lock
* process A thread 1 blocks taking read lock on process B
* process B thread 1 blocks taking read lock on process A
*
* Disable page faults to prevent potential deadlock
* and retry the copy outside the mmap_lock.
*/
pagefault_disable();
ret = copy_from_user(kaddr, (const void __user *) src_addr,
PAGE_SIZE);
mm/userfaultfd: replace kmap/kmap_atomic() with kmap_local_page() kmap() and kmap_atomic() are being deprecated in favor of kmap_local_page() which is appropriate for any thread local context.[1] A recent locking bug report with userfaultfd showed that the conversion of the kmap_atomic()'s in those code flows requires care with regard to the prevention of deadlock.[2] git archaeology implied that the recursion may not be an actual bug.[3] However, depending on the implementation of the mmap_lock and the condition of the call there may still be a deadlock.[4] So this is not purely a lockdep issue. Considering a single threaded call stack there are 3 options. 1) Different mm's are in play (no issue) 2) Readlock implementation is recursive and same mm is in play (no issue) 3) Readlock implementation is _not_ recursive (issue) The mmap_lock is recursive so with a single thread there is no issue. However, Matthew pointed out a deadlock scenario when you consider additional process' and threads thusly. "The readlock implementation is only recursive if nobody else has taken a write lock. If you have a multithreaded process, one of the other threads can call mmap() and that will prevent recursion (due to fairness). Even if it's a different process that you're trying to acquire the mmap read lock on, you can still get into a deadly embrace. eg: process A thread 1 takes read lock on own mmap_lock process A thread 2 calls mmap, blocks taking write lock process B thread 1 takes page fault, read lock on own mmap lock process B thread 2 calls mmap, blocks taking write lock process A thread 1 blocks taking read lock on process B process B thread 1 blocks taking read lock on process A Now all four threads are blocked waiting for each other." Regardless using pagefault_disable() ensures that no matter what locking implementation is used a deadlock will not occur. Complete kmap conversion in userfaultfd by replacing the kmap() and kmap_atomic() calls with kmap_local_page(). When replacing the kmap_atomic() call ensure page faults continue to be disabled to support the correct fall back behavior and add a comment to inform future souls of the requirement. [1] https://lore.kernel.org/all/20220813220034.806698-1-ira.weiny@intel.com/ [2] https://lore.kernel.org/all/Y1Mh2S7fUGQ%2FiKFR@iweiny-desk3/ [3] https://lore.kernel.org/all/Y1MymJ%2FINb45AdaY@iweiny-desk3/ [4] https://lore.kernel.org/lkml/Y1bXBtGTCym77%2FoD@casper.infradead.org/ [ira.weiny@intel.com: v2] Link: https://lkml.kernel.org/r/20221025220136.2366143-1-ira.weiny@intel.com Link: https://lkml.kernel.org/r/20221024043452.1491677-1-ira.weiny@intel.com Signed-off-by: Ira Weiny <ira.weiny@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-10-24 04:34:52 +00:00
pagefault_enable();
kunmap_local(kaddr);
/* fallback to copy_from_user outside mmap_lock */
if (unlikely(ret)) {
userfaultfd: use ENOENT instead of EFAULT if the atomic copy user fails Patch series "userfaultfd shmem updates". Jann found two bugs in the userfaultfd shmem MAP_SHARED backend: the lack of the VM_MAYWRITE check and the lack of i_size checks. Then looking into the above we also fixed the MAP_PRIVATE case. Hugh by source review also found a data loss source if UFFDIO_COPY is used on shmem MAP_SHARED PROT_READ mappings (the production usages incidentally run with PROT_READ|PROT_WRITE, so the data loss couldn't happen in those production usages like with QEMU). The whole patchset is marked for stable. We verified QEMU postcopy live migration with guest running on shmem MAP_PRIVATE run as well as before after the fix of shmem MAP_PRIVATE. Regardless if it's shmem or hugetlbfs or MAP_PRIVATE or MAP_SHARED, QEMU unconditionally invokes a punch hole if the guest mapping is filebacked and a MADV_DONTNEED too (needed to get rid of the MAP_PRIVATE COWs and for the anon backend). This patch (of 5): We internally used EFAULT to communicate with the caller, switch to ENOENT, so EFAULT can be used as a non internal retval. Link: http://lkml.kernel.org/r/20181126173452.26955-2-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Jann Horn <jannh@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30 22:09:25 +00:00
ret = -ENOENT;
*foliop = folio;
/* don't free the page */
goto out;
}
flush_dcache_folio(folio);
} else {
folio = *foliop;
*foliop = NULL;
}
/*
* The memory barrier inside __folio_mark_uptodate makes sure that
* preceding stores to the page contents become visible before
* the set_pte_at() write.
*/
__folio_mark_uptodate(folio);
ret = -ENOMEM;
if (mem_cgroup_charge(folio, dst_vma->vm_mm, GFP_KERNEL))
goto out_release;
ret = mfill_atomic_install_pte(dst_pmd, dst_vma, dst_addr,
&folio->page, true, flags);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
if (ret)
goto out_release;
out:
return ret;
out_release:
folio_put(folio);
goto out;
}
static int mfill_atomic_pte_zeropage(pmd_t *dst_pmd,
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
struct vm_area_struct *dst_vma,
unsigned long dst_addr)
{
pte_t _dst_pte, *dst_pte;
spinlock_t *ptl;
int ret;
_dst_pte = pte_mkspecial(pfn_pte(my_zero_pfn(dst_addr),
dst_vma->vm_page_prot));
mm/userfaultfd: allow pte_offset_map_lock() to fail mfill_atomic_install_pte() and mfill_atomic_pte_zeropage() treat failed pte_offset_map_lock() as -EAGAIN, which mfill_atomic() already returns to user for a similar race. Link: https://lkml.kernel.org/r/50cf3930-1bfa-4de9-a079-3da47b7ce17b@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 01:26:04 +00:00
ret = -EAGAIN;
dst_pte = pte_offset_map_lock(dst_vma->vm_mm, dst_pmd, dst_addr, &ptl);
mm/userfaultfd: allow pte_offset_map_lock() to fail mfill_atomic_install_pte() and mfill_atomic_pte_zeropage() treat failed pte_offset_map_lock() as -EAGAIN, which mfill_atomic() already returns to user for a similar race. Link: https://lkml.kernel.org/r/50cf3930-1bfa-4de9-a079-3da47b7ce17b@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 01:26:04 +00:00
if (!dst_pte)
goto out;
mm: userfaultfd: extract file size check out into a helper This code is already duplicated twice, and UFFDIO_POISON will do the same check a third time. So, it's worth extracting into a helper to save repetitive lines of code. Link: https://lkml.kernel.org/r/20230707215540.2324998-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:35 +00:00
if (mfill_file_over_size(dst_vma, dst_addr)) {
ret = -EFAULT;
mm: userfaultfd: extract file size check out into a helper This code is already duplicated twice, and UFFDIO_POISON will do the same check a third time. So, it's worth extracting into a helper to save repetitive lines of code. Link: https://lkml.kernel.org/r/20230707215540.2324998-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:35 +00:00
goto out_unlock;
}
ret = -EEXIST;
mm: ptep_get() conversion Convert all instances of direct pte_t* dereferencing to instead use ptep_get() helper. This means that by default, the accesses change from a C dereference to a READ_ONCE(). This is technically the correct thing to do since where pgtables are modified by HW (for access/dirty) they are volatile and therefore we should always ensure READ_ONCE() semantics. But more importantly, by always using the helper, it can be overridden by the architecture to fully encapsulate the contents of the pte. Arch code is deliberately not converted, as the arch code knows best. It is intended that arch code (arm64) will override the default with its own implementation that can (e.g.) hide certain bits from the core code, or determine young/dirty status by mixing in state from another source. Conversion was done using Coccinelle: ---- // $ make coccicheck \ // COCCI=ptepget.cocci \ // SPFLAGS="--include-headers" \ // MODE=patch virtual patch @ depends on patch @ pte_t *v; @@ - *v + ptep_get(v) ---- Then reviewed and hand-edited to avoid multiple unnecessary calls to ptep_get(), instead opting to store the result of a single call in a variable, where it is correct to do so. This aims to negate any cost of READ_ONCE() and will benefit arch-overrides that may be more complex. Included is a fix for an issue in an earlier version of this patch that was pointed out by kernel test robot. The issue arose because config MMU=n elides definition of the ptep helper functions, including ptep_get(). HUGETLB_PAGE=n configs still define a simple huge_ptep_clear_flush() for linking purposes, which dereferences the ptep. So when both configs are disabled, this caused a build error because ptep_get() is not defined. Fix by continuing to do a direct dereference when MMU=n. This is safe because for this config the arch code cannot be trying to virtualize the ptes because none of the ptep helpers are defined. Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/ Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: SeongJae Park <sj@kernel.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 15:15:45 +00:00
if (!pte_none(ptep_get(dst_pte)))
goto out_unlock;
set_pte_at(dst_vma->vm_mm, dst_addr, dst_pte, _dst_pte);
/* No need to invalidate - it was non-present before */
update_mmu_cache(dst_vma, dst_addr, dst_pte);
ret = 0;
out_unlock:
pte_unmap_unlock(dst_pte, ptl);
mm/userfaultfd: allow pte_offset_map_lock() to fail mfill_atomic_install_pte() and mfill_atomic_pte_zeropage() treat failed pte_offset_map_lock() as -EAGAIN, which mfill_atomic() already returns to user for a similar race. Link: https://lkml.kernel.org/r/50cf3930-1bfa-4de9-a079-3da47b7ce17b@google.com Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Christoph Hellwig <hch@infradead.org> Cc: David Hildenbrand <david@redhat.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: SeongJae Park <sj@kernel.org> Cc: Song Liu <song@kernel.org> Cc: Steven Price <steven.price@arm.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yang Shi <shy828301@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: Zack Rusin <zackr@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-09 01:26:04 +00:00
out:
return ret;
}
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
/* Handles UFFDIO_CONTINUE for all shmem VMAs (shared or private). */
static int mfill_atomic_pte_continue(pmd_t *dst_pmd,
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
struct vm_area_struct *dst_vma,
unsigned long dst_addr,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
uffd_flags_t flags)
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
{
struct inode *inode = file_inode(dst_vma->vm_file);
pgoff_t pgoff = linear_page_index(dst_vma, dst_addr);
struct folio *folio;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
struct page *page;
int ret;
ret = shmem_get_folio(inode, pgoff, &folio, SGP_NOALLOC);
/* Our caller expects us to return -EFAULT if we failed to find folio */
if (ret == -ENOENT)
ret = -EFAULT;
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
if (ret)
goto out;
if (!folio) {
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
ret = -EFAULT;
goto out;
}
page = folio_file_page(folio, pgoff);
mm: shmem: don't truncate page if memory failure happens The current behavior of memory failure is to truncate the page cache regardless of dirty or clean. If the page is dirty the later access will get the obsolete data from disk without any notification to the users. This may cause silent data loss. It is even worse for shmem since shmem is in-memory filesystem, truncating page cache means discarding data blocks. The later read would return all zero. The right approach is to keep the corrupted page in page cache, any later access would return error for syscalls or SIGBUS for page fault, until the file is truncated, hole punched or removed. The regular storage backed filesystems would be more complicated so this patch is focused on shmem. This also unblock the support for soft offlining shmem THP. [akpm@linux-foundation.org: coding style fixes] [arnd@arndb.de: fix uninitialized variable use in me_pagecache_clean()] Link: https://lkml.kernel.org/r/20211022064748.4173718-1-arnd@kernel.org [Fix invalid pointer dereference in shmem_read_mapping_page_gfp() with a slight different implementation from what Ajay Garg <ajaygargnsit@gmail.com> and Muchun Song <songmuchun@bytedance.com> proposed and reworked the error handling of shmem_write_begin() suggested by Linus] Link: https://lore.kernel.org/linux-mm/20211111084617.6746-1-ajaygargnsit@gmail.com/ Link: https://lkml.kernel.org/r/20211020210755.23964-6-shy828301@gmail.com Link: https://lkml.kernel.org/r/20211116193247.21102-1-shy828301@gmail.com Signed-off-by: Yang Shi <shy828301@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Hugh Dickins <hughd@google.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Peter Xu <peterx@redhat.com> Cc: Ajay Garg <ajaygargnsit@gmail.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Andy Lavr <andy.lavr@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-01-14 22:05:19 +00:00
if (PageHWPoison(page)) {
ret = -EIO;
goto out_release;
}
ret = mfill_atomic_install_pte(dst_pmd, dst_vma, dst_addr,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
page, false, flags);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
if (ret)
goto out_release;
folio_unlock(folio);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
ret = 0;
out:
return ret;
out_release:
folio_unlock(folio);
folio_put(folio);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
goto out;
}
mm: userfaultfd: add new UFFDIO_POISON ioctl The basic idea here is to "simulate" memory poisoning for VMs. A VM running on some host might encounter a memory error, after which some page(s) are poisoned (i.e., future accesses SIGBUS). They expect that once poisoned, pages can never become "un-poisoned". So, when we live migrate the VM, we need to preserve the poisoned status of these pages. When live migrating, we try to get the guest running on its new host as quickly as possible. So, we start it running before all memory has been copied, and before we're certain which pages should be poisoned or not. So the basic way to use this new feature is: - On the new host, the guest's memory is registered with userfaultfd, in either MISSING or MINOR mode (doesn't really matter for this purpose). - On any first access, we get a userfaultfd event. At this point we can communicate with the old host to find out if the page was poisoned. - If so, we can respond with a UFFDIO_POISON - this places a swap marker so any future accesses will SIGBUS. Because the pte is now "present", future accesses won't generate more userfaultfd events, they'll just SIGBUS directly. UFFDIO_POISON does not handle unmapping previously-present PTEs. This isn't needed, because during live migration we want to intercept all accesses with userfaultfd (not just writes, so WP mode isn't useful for this). So whether minor or missing mode is being used (or both), the PTE won't be present in any case, so handling that case isn't needed. Similarly, UFFDIO_POISON won't replace existing PTE markers. This might be okay to do, but it seems to be safer to just refuse to overwrite any existing entry (like a UFFD_WP PTE marker). Link: https://lkml.kernel.org/r/20230707215540.2324998-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:36 +00:00
/* Handles UFFDIO_POISON for all non-hugetlb VMAs. */
static int mfill_atomic_pte_poison(pmd_t *dst_pmd,
struct vm_area_struct *dst_vma,
unsigned long dst_addr,
uffd_flags_t flags)
{
int ret;
struct mm_struct *dst_mm = dst_vma->vm_mm;
pte_t _dst_pte, *dst_pte;
spinlock_t *ptl;
_dst_pte = make_pte_marker(PTE_MARKER_POISONED);
ret = -EAGAIN;
mm: userfaultfd: add new UFFDIO_POISON ioctl The basic idea here is to "simulate" memory poisoning for VMs. A VM running on some host might encounter a memory error, after which some page(s) are poisoned (i.e., future accesses SIGBUS). They expect that once poisoned, pages can never become "un-poisoned". So, when we live migrate the VM, we need to preserve the poisoned status of these pages. When live migrating, we try to get the guest running on its new host as quickly as possible. So, we start it running before all memory has been copied, and before we're certain which pages should be poisoned or not. So the basic way to use this new feature is: - On the new host, the guest's memory is registered with userfaultfd, in either MISSING or MINOR mode (doesn't really matter for this purpose). - On any first access, we get a userfaultfd event. At this point we can communicate with the old host to find out if the page was poisoned. - If so, we can respond with a UFFDIO_POISON - this places a swap marker so any future accesses will SIGBUS. Because the pte is now "present", future accesses won't generate more userfaultfd events, they'll just SIGBUS directly. UFFDIO_POISON does not handle unmapping previously-present PTEs. This isn't needed, because during live migration we want to intercept all accesses with userfaultfd (not just writes, so WP mode isn't useful for this). So whether minor or missing mode is being used (or both), the PTE won't be present in any case, so handling that case isn't needed. Similarly, UFFDIO_POISON won't replace existing PTE markers. This might be okay to do, but it seems to be safer to just refuse to overwrite any existing entry (like a UFFD_WP PTE marker). Link: https://lkml.kernel.org/r/20230707215540.2324998-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:36 +00:00
dst_pte = pte_offset_map_lock(dst_mm, dst_pmd, dst_addr, &ptl);
if (!dst_pte)
goto out;
mm: userfaultfd: add new UFFDIO_POISON ioctl The basic idea here is to "simulate" memory poisoning for VMs. A VM running on some host might encounter a memory error, after which some page(s) are poisoned (i.e., future accesses SIGBUS). They expect that once poisoned, pages can never become "un-poisoned". So, when we live migrate the VM, we need to preserve the poisoned status of these pages. When live migrating, we try to get the guest running on its new host as quickly as possible. So, we start it running before all memory has been copied, and before we're certain which pages should be poisoned or not. So the basic way to use this new feature is: - On the new host, the guest's memory is registered with userfaultfd, in either MISSING or MINOR mode (doesn't really matter for this purpose). - On any first access, we get a userfaultfd event. At this point we can communicate with the old host to find out if the page was poisoned. - If so, we can respond with a UFFDIO_POISON - this places a swap marker so any future accesses will SIGBUS. Because the pte is now "present", future accesses won't generate more userfaultfd events, they'll just SIGBUS directly. UFFDIO_POISON does not handle unmapping previously-present PTEs. This isn't needed, because during live migration we want to intercept all accesses with userfaultfd (not just writes, so WP mode isn't useful for this). So whether minor or missing mode is being used (or both), the PTE won't be present in any case, so handling that case isn't needed. Similarly, UFFDIO_POISON won't replace existing PTE markers. This might be okay to do, but it seems to be safer to just refuse to overwrite any existing entry (like a UFFD_WP PTE marker). Link: https://lkml.kernel.org/r/20230707215540.2324998-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:36 +00:00
if (mfill_file_over_size(dst_vma, dst_addr)) {
ret = -EFAULT;
goto out_unlock;
}
ret = -EEXIST;
/* Refuse to overwrite any PTE, even a PTE marker (e.g. UFFD WP). */
if (!pte_none(*dst_pte))
goto out_unlock;
set_pte_at(dst_mm, dst_addr, dst_pte, _dst_pte);
/* No need to invalidate - it was non-present before */
update_mmu_cache(dst_vma, dst_addr, dst_pte);
ret = 0;
out_unlock:
pte_unmap_unlock(dst_pte, ptl);
out:
mm: userfaultfd: add new UFFDIO_POISON ioctl The basic idea here is to "simulate" memory poisoning for VMs. A VM running on some host might encounter a memory error, after which some page(s) are poisoned (i.e., future accesses SIGBUS). They expect that once poisoned, pages can never become "un-poisoned". So, when we live migrate the VM, we need to preserve the poisoned status of these pages. When live migrating, we try to get the guest running on its new host as quickly as possible. So, we start it running before all memory has been copied, and before we're certain which pages should be poisoned or not. So the basic way to use this new feature is: - On the new host, the guest's memory is registered with userfaultfd, in either MISSING or MINOR mode (doesn't really matter for this purpose). - On any first access, we get a userfaultfd event. At this point we can communicate with the old host to find out if the page was poisoned. - If so, we can respond with a UFFDIO_POISON - this places a swap marker so any future accesses will SIGBUS. Because the pte is now "present", future accesses won't generate more userfaultfd events, they'll just SIGBUS directly. UFFDIO_POISON does not handle unmapping previously-present PTEs. This isn't needed, because during live migration we want to intercept all accesses with userfaultfd (not just writes, so WP mode isn't useful for this). So whether minor or missing mode is being used (or both), the PTE won't be present in any case, so handling that case isn't needed. Similarly, UFFDIO_POISON won't replace existing PTE markers. This might be okay to do, but it seems to be safer to just refuse to overwrite any existing entry (like a UFFD_WP PTE marker). Link: https://lkml.kernel.org/r/20230707215540.2324998-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:36 +00:00
return ret;
}
static pmd_t *mm_alloc_pmd(struct mm_struct *mm, unsigned long address)
{
pgd_t *pgd;
p4d_t *p4d;
pud_t *pud;
pgd = pgd_offset(mm, address);
p4d = p4d_alloc(mm, pgd, address);
if (!p4d)
return NULL;
pud = pud_alloc(mm, p4d, address);
if (!pud)
return NULL;
/*
* Note that we didn't run this because the pmd was
* missing, the *pmd may be already established and in
* turn it may also be a trans_huge_pmd.
*/
return pmd_alloc(mm, pud, address);
}
#ifdef CONFIG_HUGETLB_PAGE
/*
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
* mfill_atomic processing for HUGETLB vmas. Note that this routine is
* called with mmap_lock held, it will release mmap_lock before returning.
*/
static __always_inline ssize_t mfill_atomic_hugetlb(
struct vm_area_struct *dst_vma,
unsigned long dst_start,
unsigned long src_start,
unsigned long len,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
uffd_flags_t flags)
{
struct mm_struct *dst_mm = dst_vma->vm_mm;
int vm_shared = dst_vma->vm_flags & VM_SHARED;
ssize_t err;
pte_t *dst_pte;
unsigned long src_addr, dst_addr;
long copied;
struct folio *folio;
unsigned long vma_hpagesize;
pgoff_t idx;
u32 hash;
struct address_space *mapping;
/*
* There is no default zero huge page for all huge page sizes as
* supported by hugetlb. A PMD_SIZE huge pages may exist as used
* by THP. Since we can not reliably insert a zero page, this
* feature is not supported.
*/
2023-07-07 21:55:37 +00:00
if (uffd_flags_mode_is(flags, MFILL_ATOMIC_ZEROPAGE)) {
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_unlock(dst_mm);
return -EINVAL;
}
src_addr = src_start;
dst_addr = dst_start;
copied = 0;
folio = NULL;
vma_hpagesize = vma_kernel_pagesize(dst_vma);
/*
* Validate alignment based on huge page size
*/
err = -EINVAL;
if (dst_start & (vma_hpagesize - 1) || len & (vma_hpagesize - 1))
goto out_unlock;
retry:
/*
* On routine entry dst_vma is set. If we had to drop mmap_lock and
* retry, dst_vma will be set to NULL and we must lookup again.
*/
if (!dst_vma) {
err = -ENOENT;
dst_vma = find_dst_vma(dst_mm, dst_start, len);
if (!dst_vma || !is_vm_hugetlb_page(dst_vma))
goto out_unlock;
err = -EINVAL;
if (vma_hpagesize != vma_kernel_pagesize(dst_vma))
goto out_unlock;
vm_shared = dst_vma->vm_flags & VM_SHARED;
}
/*
* If not shared, ensure the dst_vma has a anon_vma.
*/
err = -ENOMEM;
if (!vm_shared) {
if (unlikely(anon_vma_prepare(dst_vma)))
goto out_unlock;
}
while (src_addr < src_start + len) {
BUG_ON(dst_addr >= dst_start + len);
/*
hugetlb: use new vma_lock for pmd sharing synchronization The new hugetlb vma lock is used to address this race: Faulting thread Unsharing thread ... ... ptep = huge_pte_offset() or ptep = huge_pte_alloc() ... i_mmap_lock_write lock page table ptep invalid <------------------------ huge_pmd_unshare() Could be in a previously unlock_page_table sharing process or worse i_mmap_unlock_write ... The vma_lock is used as follows: - During fault processing. The lock is acquired in read mode before doing a page table lock and allocation (huge_pte_alloc). The lock is held until code is finished with the page table entry (ptep). - The lock must be held in write mode whenever huge_pmd_unshare is called. Lock ordering issues come into play when unmapping a page from all vmas mapping the page. The i_mmap_rwsem must be held to search for the vmas, and the vma lock must be held before calling unmap which will call huge_pmd_unshare. This is done today in: - try_to_migrate_one and try_to_unmap_ for page migration and memory error handling. In these routines we 'try' to obtain the vma lock and fail to unmap if unsuccessful. Calling routines already deal with the failure of unmapping. - hugetlb_vmdelete_list for truncation and hole punch. This routine also tries to acquire the vma lock. If it fails, it skips the unmapping. However, we can not have file truncation or hole punch fail because of contention. After hugetlb_vmdelete_list, truncation and hole punch call remove_inode_hugepages. remove_inode_hugepages checks for mapped pages and call hugetlb_unmap_file_page to unmap them. hugetlb_unmap_file_page is designed to drop locks and reacquire in the correct order to guarantee unmap success. Link: https://lkml.kernel.org/r/20220914221810.95771-9-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: James Houghton <jthoughton@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-14 22:18:09 +00:00
* Serialize via vma_lock and hugetlb_fault_mutex.
* vma_lock ensures the dst_pte remains valid even
* in the case of shared pmds. fault mutex prevents
* races with other faulting threads.
*/
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization Patch series "hugetlbfs: use i_mmap_rwsem for more synchronization", v2. While discussing the issue with huge_pte_offset [1], I remembered that there were more outstanding hugetlb races. These issues are: 1) For shared pmds, huge PTE pointers returned by huge_pte_alloc can become invalid via a call to huge_pmd_unshare by another thread. 2) hugetlbfs page faults can race with truncation causing invalid global reserve counts and state. A previous attempt was made to use i_mmap_rwsem in this manner as described at [2]. However, those patches were reverted starting with [3] due to locking issues. To effectively use i_mmap_rwsem to address the above issues it needs to be held (in read mode) during page fault processing. However, during fault processing we need to lock the page we will be adding. Lock ordering requires we take page lock before i_mmap_rwsem. Waiting until after taking the page lock is too late in the fault process for the synchronization we want to do. To address this lock ordering issue, the following patches change the lock ordering for hugetlb pages. This is not too invasive as hugetlbfs processing is done separate from core mm in many places. However, I don't really like this idea. Much ugliness is contained in the new routine hugetlb_page_mapping_lock_write() of patch 1. The only other way I can think of to address these issues is by catching all the races. After catching a race, cleanup, backout, retry ... etc, as needed. This can get really ugly, especially for huge page reservations. At one time, I started writing some of the reservation backout code for page faults and it got so ugly and complicated I went down the path of adding synchronization to avoid the races. Any other suggestions would be welcome. [1] https://lore.kernel.org/linux-mm/1582342427-230392-1-git-send-email-longpeng2@huawei.com/ [2] https://lore.kernel.org/linux-mm/20181222223013.22193-1-mike.kravetz@oracle.com/ [3] https://lore.kernel.org/linux-mm/20190103235452.29335-1-mike.kravetz@oracle.com [4] https://lore.kernel.org/linux-mm/1584028670.7365.182.camel@lca.pw/ [5] https://lore.kernel.org/lkml/20200312183142.108df9ac@canb.auug.org.au/ This patch (of 2): While looking at BUGs associated with invalid huge page map counts, it was discovered and observed that a huge pte pointer could become 'invalid' and point to another task's page table. Consider the following: A task takes a page fault on a shared hugetlbfs file and calls huge_pte_alloc to get a ptep. Suppose the returned ptep points to a shared pmd. Now, another task truncates the hugetlbfs file. As part of truncation, it unmaps everyone who has the file mapped. If the range being truncated is covered by a shared pmd, huge_pmd_unshare will be called. For all but the last user of the shared pmd, huge_pmd_unshare will clear the pud pointing to the pmd. If the task in the middle of the page fault is not the last user, the ptep returned by huge_pte_alloc now points to another task's page table or worse. This leads to bad things such as incorrect page map/reference counts or invalid memory references. To fix, expand the use of i_mmap_rwsem as follows: - i_mmap_rwsem is held in read mode whenever huge_pmd_share is called. huge_pmd_share is only called via huge_pte_alloc, so callers of huge_pte_alloc take i_mmap_rwsem before calling. In addition, callers of huge_pte_alloc continue to hold the semaphore until finished with the ptep. - i_mmap_rwsem is held in write mode whenever huge_pmd_unshare is called. One problem with this scheme is that it requires taking i_mmap_rwsem before taking the page lock during page faults. This is not the order specified in the rest of mm code. Handling of hugetlbfs pages is mostly isolated today. Therefore, we use this alternative locking order for PageHuge() pages. mapping->i_mmap_rwsem hugetlb_fault_mutex (hugetlbfs specific page fault mutex) page->flags PG_locked (lock_page) To help with lock ordering issues, hugetlb_page_mapping_lock_write() is introduced to write lock the i_mmap_rwsem associated with a page. In most cases it is easy to get address_space via vma->vm_file->f_mapping. However, in the case of migration or memory errors for anon pages we do not have an associated vma. A new routine _get_hugetlb_page_mapping() will use anon_vma to get address_space in these cases. Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Link: http://lkml.kernel.org/r/20200316205756.146666-2-mike.kravetz@oracle.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-02 04:11:05 +00:00
idx = linear_page_index(dst_vma, dst_addr);
hugetlbfs: revert use i_mmap_rwsem for more pmd sharing synchronization Commit c0d0381ade79 ("hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization") added code to take i_mmap_rwsem in read mode for the duration of fault processing. However, this has been shown to cause performance/scaling issues. Revert the code and go back to only taking the semaphore in huge_pmd_share during the fault path. Keep the code that takes i_mmap_rwsem in write mode before calling try_to_unmap as this is required if huge_pmd_unshare is called. NOTE: Reverting this code does expose the following race condition. Faulting thread Unsharing thread ... ... ptep = huge_pte_offset() or ptep = huge_pte_alloc() ... i_mmap_lock_write lock page table ptep invalid <------------------------ huge_pmd_unshare() Could be in a previously unlock_page_table sharing process or worse i_mmap_unlock_write ... ptl = huge_pte_lock(ptep) get/update pte set_pte_at(pte, ptep) It is unknown if the above race was ever experienced by a user. It was discovered via code inspection when initially addressed. In subsequent patches, a new synchronization mechanism will be added to coordinate pmd sharing and eliminate this race. Link: https://lkml.kernel.org/r/20220914221810.95771-3-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: James Houghton <jthoughton@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-14 22:18:03 +00:00
mapping = dst_vma->vm_file->f_mapping;
hash = hugetlb_fault_mutex_hash(mapping, idx);
mutex_lock(&hugetlb_fault_mutex_table[hash]);
hugetlb: use new vma_lock for pmd sharing synchronization The new hugetlb vma lock is used to address this race: Faulting thread Unsharing thread ... ... ptep = huge_pte_offset() or ptep = huge_pte_alloc() ... i_mmap_lock_write lock page table ptep invalid <------------------------ huge_pmd_unshare() Could be in a previously unlock_page_table sharing process or worse i_mmap_unlock_write ... The vma_lock is used as follows: - During fault processing. The lock is acquired in read mode before doing a page table lock and allocation (huge_pte_alloc). The lock is held until code is finished with the page table entry (ptep). - The lock must be held in write mode whenever huge_pmd_unshare is called. Lock ordering issues come into play when unmapping a page from all vmas mapping the page. The i_mmap_rwsem must be held to search for the vmas, and the vma lock must be held before calling unmap which will call huge_pmd_unshare. This is done today in: - try_to_migrate_one and try_to_unmap_ for page migration and memory error handling. In these routines we 'try' to obtain the vma lock and fail to unmap if unsuccessful. Calling routines already deal with the failure of unmapping. - hugetlb_vmdelete_list for truncation and hole punch. This routine also tries to acquire the vma lock. If it fails, it skips the unmapping. However, we can not have file truncation or hole punch fail because of contention. After hugetlb_vmdelete_list, truncation and hole punch call remove_inode_hugepages. remove_inode_hugepages checks for mapped pages and call hugetlb_unmap_file_page to unmap them. hugetlb_unmap_file_page is designed to drop locks and reacquire in the correct order to guarantee unmap success. Link: https://lkml.kernel.org/r/20220914221810.95771-9-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: James Houghton <jthoughton@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-14 22:18:09 +00:00
hugetlb_vma_lock_read(dst_vma);
err = -ENOMEM;
hugetlb: pass vma into huge_pte_alloc() and huge_pmd_share() Patch series "hugetlb: Disable huge pmd unshare for uffd-wp", v4. This series tries to disable huge pmd unshare of hugetlbfs backed memory for uffd-wp. Although uffd-wp of hugetlbfs is still during rfc stage, the idea of this series may be needed for multiple tasks (Axel's uffd minor fault series, and Mike's soft dirty series), so I picked it out from the larger series. This patch (of 4): It is a preparation work to be able to behave differently in the per architecture huge_pte_alloc() according to different VMA attributes. Pass it deeper into huge_pmd_share() so that we can avoid the find_vma() call. [peterx@redhat.com: build fix] Link: https://lkml.kernel.org/r/20210304164653.GB397383@xz-x1Link: https://lkml.kernel.org/r/20210218230633.15028-1-peterx@redhat.com Link: https://lkml.kernel.org/r/20210218230633.15028-2-peterx@redhat.com Signed-off-by: Peter Xu <peterx@redhat.com> Suggested-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Adam Ruprecht <ruprecht@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Cannon Matthews <cannonmatthews@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chinwen Chang <chinwen.chang@mediatek.com> Cc: David Rientjes <rientjes@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: "Michal Koutn" <mkoutny@suse.com> Cc: Michel Lespinasse <walken@google.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shawn Anastasio <shawn@anastas.io> Cc: Steven Price <steven.price@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:33:00 +00:00
dst_pte = huge_pte_alloc(dst_mm, dst_vma, dst_addr, vma_hpagesize);
if (!dst_pte) {
hugetlb: use new vma_lock for pmd sharing synchronization The new hugetlb vma lock is used to address this race: Faulting thread Unsharing thread ... ... ptep = huge_pte_offset() or ptep = huge_pte_alloc() ... i_mmap_lock_write lock page table ptep invalid <------------------------ huge_pmd_unshare() Could be in a previously unlock_page_table sharing process or worse i_mmap_unlock_write ... The vma_lock is used as follows: - During fault processing. The lock is acquired in read mode before doing a page table lock and allocation (huge_pte_alloc). The lock is held until code is finished with the page table entry (ptep). - The lock must be held in write mode whenever huge_pmd_unshare is called. Lock ordering issues come into play when unmapping a page from all vmas mapping the page. The i_mmap_rwsem must be held to search for the vmas, and the vma lock must be held before calling unmap which will call huge_pmd_unshare. This is done today in: - try_to_migrate_one and try_to_unmap_ for page migration and memory error handling. In these routines we 'try' to obtain the vma lock and fail to unmap if unsuccessful. Calling routines already deal with the failure of unmapping. - hugetlb_vmdelete_list for truncation and hole punch. This routine also tries to acquire the vma lock. If it fails, it skips the unmapping. However, we can not have file truncation or hole punch fail because of contention. After hugetlb_vmdelete_list, truncation and hole punch call remove_inode_hugepages. remove_inode_hugepages checks for mapped pages and call hugetlb_unmap_file_page to unmap them. hugetlb_unmap_file_page is designed to drop locks and reacquire in the correct order to guarantee unmap success. Link: https://lkml.kernel.org/r/20220914221810.95771-9-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: James Houghton <jthoughton@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-14 22:18:09 +00:00
hugetlb_vma_unlock_read(dst_vma);
mutex_unlock(&hugetlb_fault_mutex_table[hash]);
goto out_unlock;
}
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
if (!uffd_flags_mode_is(flags, MFILL_ATOMIC_CONTINUE) &&
!huge_pte_none_mostly(huge_ptep_get(dst_pte))) {
userfaultfd: add UFFDIO_CONTINUE ioctl This ioctl is how userspace ought to resolve "minor" userfaults. The idea is, userspace is notified that a minor fault has occurred. It might change the contents of the page using its second non-UFFD mapping, or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have ensured the page contents are correct, carry on setting up the mapping". Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in the minor fault case, we already have some pre-existing underlying page. Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping. We'd just use memcpy() or similar instead. It turns out hugetlb_mcopy_atomic_pte() already does very close to what we want, if an existing page is provided via `struct page **pagep`. We already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so just extend that design: add an enum for the three modes of operation, and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE case. (Basically, look up the existing page, and avoid adding the existing page to the page cache or calling set_page_huge_active() on it.) Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Adam Ruprecht <ruprecht@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Cannon Matthews <cannonmatthews@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chinwen Chang <chinwen.chang@mediatek.com> Cc: David Rientjes <rientjes@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: "Michal Koutn" <mkoutny@suse.com> Cc: Michel Lespinasse <walken@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shawn Anastasio <shawn@anastas.io> Cc: Steven Price <steven.price@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
err = -EEXIST;
hugetlb: use new vma_lock for pmd sharing synchronization The new hugetlb vma lock is used to address this race: Faulting thread Unsharing thread ... ... ptep = huge_pte_offset() or ptep = huge_pte_alloc() ... i_mmap_lock_write lock page table ptep invalid <------------------------ huge_pmd_unshare() Could be in a previously unlock_page_table sharing process or worse i_mmap_unlock_write ... The vma_lock is used as follows: - During fault processing. The lock is acquired in read mode before doing a page table lock and allocation (huge_pte_alloc). The lock is held until code is finished with the page table entry (ptep). - The lock must be held in write mode whenever huge_pmd_unshare is called. Lock ordering issues come into play when unmapping a page from all vmas mapping the page. The i_mmap_rwsem must be held to search for the vmas, and the vma lock must be held before calling unmap which will call huge_pmd_unshare. This is done today in: - try_to_migrate_one and try_to_unmap_ for page migration and memory error handling. In these routines we 'try' to obtain the vma lock and fail to unmap if unsuccessful. Calling routines already deal with the failure of unmapping. - hugetlb_vmdelete_list for truncation and hole punch. This routine also tries to acquire the vma lock. If it fails, it skips the unmapping. However, we can not have file truncation or hole punch fail because of contention. After hugetlb_vmdelete_list, truncation and hole punch call remove_inode_hugepages. remove_inode_hugepages checks for mapped pages and call hugetlb_unmap_file_page to unmap them. hugetlb_unmap_file_page is designed to drop locks and reacquire in the correct order to guarantee unmap success. Link: https://lkml.kernel.org/r/20220914221810.95771-9-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: James Houghton <jthoughton@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-14 22:18:09 +00:00
hugetlb_vma_unlock_read(dst_vma);
mutex_unlock(&hugetlb_fault_mutex_table[hash]);
goto out_unlock;
}
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
err = hugetlb_mfill_atomic_pte(dst_pte, dst_vma, dst_addr,
src_addr, flags, &folio);
hugetlb: use new vma_lock for pmd sharing synchronization The new hugetlb vma lock is used to address this race: Faulting thread Unsharing thread ... ... ptep = huge_pte_offset() or ptep = huge_pte_alloc() ... i_mmap_lock_write lock page table ptep invalid <------------------------ huge_pmd_unshare() Could be in a previously unlock_page_table sharing process or worse i_mmap_unlock_write ... The vma_lock is used as follows: - During fault processing. The lock is acquired in read mode before doing a page table lock and allocation (huge_pte_alloc). The lock is held until code is finished with the page table entry (ptep). - The lock must be held in write mode whenever huge_pmd_unshare is called. Lock ordering issues come into play when unmapping a page from all vmas mapping the page. The i_mmap_rwsem must be held to search for the vmas, and the vma lock must be held before calling unmap which will call huge_pmd_unshare. This is done today in: - try_to_migrate_one and try_to_unmap_ for page migration and memory error handling. In these routines we 'try' to obtain the vma lock and fail to unmap if unsuccessful. Calling routines already deal with the failure of unmapping. - hugetlb_vmdelete_list for truncation and hole punch. This routine also tries to acquire the vma lock. If it fails, it skips the unmapping. However, we can not have file truncation or hole punch fail because of contention. After hugetlb_vmdelete_list, truncation and hole punch call remove_inode_hugepages. remove_inode_hugepages checks for mapped pages and call hugetlb_unmap_file_page to unmap them. hugetlb_unmap_file_page is designed to drop locks and reacquire in the correct order to guarantee unmap success. Link: https://lkml.kernel.org/r/20220914221810.95771-9-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: James Houghton <jthoughton@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Peter Xu <peterx@redhat.com> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-09-14 22:18:09 +00:00
hugetlb_vma_unlock_read(dst_vma);
mutex_unlock(&hugetlb_fault_mutex_table[hash]);
cond_resched();
userfaultfd: use ENOENT instead of EFAULT if the atomic copy user fails Patch series "userfaultfd shmem updates". Jann found two bugs in the userfaultfd shmem MAP_SHARED backend: the lack of the VM_MAYWRITE check and the lack of i_size checks. Then looking into the above we also fixed the MAP_PRIVATE case. Hugh by source review also found a data loss source if UFFDIO_COPY is used on shmem MAP_SHARED PROT_READ mappings (the production usages incidentally run with PROT_READ|PROT_WRITE, so the data loss couldn't happen in those production usages like with QEMU). The whole patchset is marked for stable. We verified QEMU postcopy live migration with guest running on shmem MAP_PRIVATE run as well as before after the fix of shmem MAP_PRIVATE. Regardless if it's shmem or hugetlbfs or MAP_PRIVATE or MAP_SHARED, QEMU unconditionally invokes a punch hole if the guest mapping is filebacked and a MADV_DONTNEED too (needed to get rid of the MAP_PRIVATE COWs and for the anon backend). This patch (of 5): We internally used EFAULT to communicate with the caller, switch to ENOENT, so EFAULT can be used as a non internal retval. Link: http://lkml.kernel.org/r/20181126173452.26955-2-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Jann Horn <jannh@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30 22:09:25 +00:00
if (unlikely(err == -ENOENT)) {
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_unlock(dst_mm);
BUG_ON(!folio);
err = copy_folio_from_user(folio,
(const void __user *)src_addr, true);
if (unlikely(err)) {
err = -EFAULT;
goto out;
}
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_lock(dst_mm);
dst_vma = NULL;
goto retry;
} else
BUG_ON(folio);
if (!err) {
dst_addr += vma_hpagesize;
src_addr += vma_hpagesize;
copied += vma_hpagesize;
if (fatal_signal_pending(current))
err = -EINTR;
}
if (err)
break;
}
out_unlock:
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_unlock(dst_mm);
out:
if (folio)
folio_put(folio);
BUG_ON(copied < 0);
BUG_ON(err > 0);
BUG_ON(!copied && !err);
return copied ? copied : err;
}
#else /* !CONFIG_HUGETLB_PAGE */
/* fail at build time if gcc attempts to use this */
extern ssize_t mfill_atomic_hugetlb(struct vm_area_struct *dst_vma,
unsigned long dst_start,
unsigned long src_start,
unsigned long len,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
uffd_flags_t flags);
#endif /* CONFIG_HUGETLB_PAGE */
static __always_inline ssize_t mfill_atomic_pte(pmd_t *dst_pmd,
struct vm_area_struct *dst_vma,
unsigned long dst_addr,
unsigned long src_addr,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
uffd_flags_t flags,
struct folio **foliop)
{
ssize_t err;
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
if (uffd_flags_mode_is(flags, MFILL_ATOMIC_CONTINUE)) {
return mfill_atomic_pte_continue(dst_pmd, dst_vma,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
dst_addr, flags);
mm: userfaultfd: add new UFFDIO_POISON ioctl The basic idea here is to "simulate" memory poisoning for VMs. A VM running on some host might encounter a memory error, after which some page(s) are poisoned (i.e., future accesses SIGBUS). They expect that once poisoned, pages can never become "un-poisoned". So, when we live migrate the VM, we need to preserve the poisoned status of these pages. When live migrating, we try to get the guest running on its new host as quickly as possible. So, we start it running before all memory has been copied, and before we're certain which pages should be poisoned or not. So the basic way to use this new feature is: - On the new host, the guest's memory is registered with userfaultfd, in either MISSING or MINOR mode (doesn't really matter for this purpose). - On any first access, we get a userfaultfd event. At this point we can communicate with the old host to find out if the page was poisoned. - If so, we can respond with a UFFDIO_POISON - this places a swap marker so any future accesses will SIGBUS. Because the pte is now "present", future accesses won't generate more userfaultfd events, they'll just SIGBUS directly. UFFDIO_POISON does not handle unmapping previously-present PTEs. This isn't needed, because during live migration we want to intercept all accesses with userfaultfd (not just writes, so WP mode isn't useful for this). So whether minor or missing mode is being used (or both), the PTE won't be present in any case, so handling that case isn't needed. Similarly, UFFDIO_POISON won't replace existing PTE markers. This might be okay to do, but it seems to be safer to just refuse to overwrite any existing entry (like a UFFD_WP PTE marker). Link: https://lkml.kernel.org/r/20230707215540.2324998-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:36 +00:00
} else if (uffd_flags_mode_is(flags, MFILL_ATOMIC_POISON)) {
return mfill_atomic_pte_poison(dst_pmd, dst_vma,
dst_addr, flags);
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
}
userfaultfd: shmem: allocate anonymous memory for MAP_PRIVATE shmem Userfaultfd did not create private memory when UFFDIO_COPY was invoked on a MAP_PRIVATE shmem mapping. Instead it wrote to the shmem file, even when that had not been opened for writing. Though, fortunately, that could only happen where there was a hole in the file. Fix the shmem-backed implementation of UFFDIO_COPY to create private memory for MAP_PRIVATE mappings. The hugetlbfs-backed implementation was already correct. This change is visible to userland, if userfaultfd has been used in unintended ways: so it introduces a small risk of incompatibility, but is necessary in order to respect file permissions. An app that uses UFFDIO_COPY for anything like postcopy live migration won't notice the difference, and in fact it'll run faster because there will be no copy-on-write and memory waste in the tmpfs pagecache anymore. Userfaults on MAP_PRIVATE shmem keep triggering only on file holes like before. The real zeropage can also be built on a MAP_PRIVATE shmem mapping through UFFDIO_ZEROPAGE and that's safe because the zeropage pte is never dirty, in turn even an mprotect upgrading the vma permission from PROT_READ to PROT_READ|PROT_WRITE won't make the zeropage pte writable. Link: http://lkml.kernel.org/r/20181126173452.26955-3-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30 22:09:28 +00:00
/*
* The normal page fault path for a shmem will invoke the
* fault, fill the hole in the file and COW it right away. The
* result generates plain anonymous memory. So when we are
* asked to fill an hole in a MAP_PRIVATE shmem mapping, we'll
* generate anonymous memory directly without actually filling
* the hole. For the MAP_PRIVATE case the robustness check
* only happens in the pagetable (to verify it's still none)
* and not in the radix tree.
*/
if (!(dst_vma->vm_flags & VM_SHARED)) {
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
if (uffd_flags_mode_is(flags, MFILL_ATOMIC_COPY))
err = mfill_atomic_pte_copy(dst_pmd, dst_vma,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
dst_addr, src_addr,
flags, foliop);
else
err = mfill_atomic_pte_zeropage(dst_pmd,
dst_vma, dst_addr);
} else {
err = shmem_mfill_atomic_pte(dst_pmd, dst_vma,
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem With this change, userspace can resolve a minor fault within a shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this match those for hugetlbfs - we look up the existing page in the page cache, and install a PTE for it. This commit introduces a new helper: mfill_atomic_install_pte. Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in shmem.c? The existing userfault implementation only relies on shmem.c for VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in one place, regardless of shared/private (to reduce code duplication). Why add a new mfill_atomic_install_pte helper? A problem we have with continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are *close* to what we want, but not exactly. We do want to setup the PTEs in a CONTINUE operation, but we don't want to e.g. allocate a new page, charge it (e.g. to the shmem inode), manipulate various flags, etc. Also we have the problem stated above: shmem_mfill_atomic_pte() and mcopy_atomic_pte() both handle one-half of the problem (shared / private) continue cares about. So, introduce mcontinue_atomic_pte(), to handle all of the shmem continue cases. Introduce the helper so it doesn't duplicate code with mcopy_atomic_pte(). In a future commit, shmem_mfill_atomic_pte() will also be modified to use this new helper. However, since this is a bigger refactor, it seems most clear to do it as a separate change. Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Brian Geffon <bgeffon@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Wang Qing <wangqing@vivo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
dst_addr, src_addr,
flags, foliop);
}
return err;
}
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
static __always_inline ssize_t mfill_atomic(struct mm_struct *dst_mm,
unsigned long dst_start,
unsigned long src_start,
unsigned long len,
atomic_t *mmap_changing,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
uffd_flags_t flags)
{
struct vm_area_struct *dst_vma;
ssize_t err;
pmd_t *dst_pmd;
unsigned long src_addr, dst_addr;
long copied;
struct folio *folio;
/*
* Sanitize the command parameters:
*/
BUG_ON(dst_start & ~PAGE_MASK);
BUG_ON(len & ~PAGE_MASK);
/* Does the address range wrap, or is the span zero-sized? */
BUG_ON(src_start + len <= src_start);
BUG_ON(dst_start + len <= dst_start);
src_addr = src_start;
dst_addr = dst_start;
copied = 0;
folio = NULL;
retry:
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_lock(dst_mm);
userfaultfd: prevent non-cooperative events vs mcopy_atomic races If a process monitored with userfaultfd changes it's memory mappings or forks() at the same time as uffd monitor fills the process memory with UFFDIO_COPY, the actual creation of page table entries and copying of the data in mcopy_atomic may happen either before of after the memory mapping modifications and there is no way for the uffd monitor to maintain consistent view of the process memory layout. For instance, let's consider fork() running in parallel with userfaultfd_copy(): process | uffd monitor ---------------------------------+------------------------------ fork() | userfaultfd_copy() ... | ... dup_mmap() | down_read(mmap_sem) down_write(mmap_sem) | /* create PTEs, copy data */ dup_uffd() | up_read(mmap_sem) copy_page_range() | up_write(mmap_sem) | dup_uffd_complete() | /* notify monitor */ | If the userfaultfd_copy() takes the mmap_sem first, the new page(s) will be present by the time copy_page_range() is called and they will appear in the child's memory mappings. However, if the fork() is the first to take the mmap_sem, the new pages won't be mapped in the child's address space. If the pages are not present and child tries to access them, the monitor will get page fault notification and everything is fine. However, if the pages *are present*, the child can access them without uffd noticing. And if we copy them into child it'll see the wrong data. Since we are talking about background copy, we'd need to decide whether the pages should be copied or not regardless #PF notifications. Since userfaultfd monitor has no way to determine what was the order, let's disallow userfaultfd_copy in parallel with the non-cooperative events. In such case we return -EAGAIN and the uffd monitor can understand that userfaultfd_copy() clashed with a non-cooperative event and take an appropriate action. Link: http://lkml.kernel.org/r/1527061324-19949-1-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-08 00:09:25 +00:00
/*
* If memory mappings are changing because of non-cooperative
* operation (e.g. mremap) running in parallel, bail out and
* request the user to retry later
*/
err = -EAGAIN;
userfaultfd: change mmap_changing to atomic Patch series "userfaultfd: minor bug fixes". Three unrelated bug fixes. The first two addresses possible issues (not too theoretical ones), but I did not encounter them in practice. The third patch addresses a test bug that causes the test to fail on my system. It has been sent before as part of a bigger RFC. This patch (of 3): mmap_changing is currently a boolean variable, which is set and cleared without any lock that protects against concurrent modifications. mmap_changing is supposed to mark whether userfaultfd page-faults handling should be retried since mappings are undergoing a change. However, concurrent calls, for instance to madvise(MADV_DONTNEED), might cause mmap_changing to be false, although the remove event was still not read (hence acknowledged) by the user. Change mmap_changing to atomic_t and increase/decrease appropriately. Add a debug assertion to see whether mmap_changing is negative. Link: https://lkml.kernel.org/r/20210808020724.1022515-1-namit@vmware.com Link: https://lkml.kernel.org/r/20210808020724.1022515-2-namit@vmware.com Fixes: df2cc96e77011 ("userfaultfd: prevent non-cooperative events vs mcopy_atomic races") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-09-02 21:58:56 +00:00
if (mmap_changing && atomic_read(mmap_changing))
userfaultfd: prevent non-cooperative events vs mcopy_atomic races If a process monitored with userfaultfd changes it's memory mappings or forks() at the same time as uffd monitor fills the process memory with UFFDIO_COPY, the actual creation of page table entries and copying of the data in mcopy_atomic may happen either before of after the memory mapping modifications and there is no way for the uffd monitor to maintain consistent view of the process memory layout. For instance, let's consider fork() running in parallel with userfaultfd_copy(): process | uffd monitor ---------------------------------+------------------------------ fork() | userfaultfd_copy() ... | ... dup_mmap() | down_read(mmap_sem) down_write(mmap_sem) | /* create PTEs, copy data */ dup_uffd() | up_read(mmap_sem) copy_page_range() | up_write(mmap_sem) | dup_uffd_complete() | /* notify monitor */ | If the userfaultfd_copy() takes the mmap_sem first, the new page(s) will be present by the time copy_page_range() is called and they will appear in the child's memory mappings. However, if the fork() is the first to take the mmap_sem, the new pages won't be mapped in the child's address space. If the pages are not present and child tries to access them, the monitor will get page fault notification and everything is fine. However, if the pages *are present*, the child can access them without uffd noticing. And if we copy them into child it'll see the wrong data. Since we are talking about background copy, we'd need to decide whether the pages should be copied or not regardless #PF notifications. Since userfaultfd monitor has no way to determine what was the order, let's disallow userfaultfd_copy in parallel with the non-cooperative events. In such case we return -EAGAIN and the uffd monitor can understand that userfaultfd_copy() clashed with a non-cooperative event and take an appropriate action. Link: http://lkml.kernel.org/r/1527061324-19949-1-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-08 00:09:25 +00:00
goto out_unlock;
/*
* Make sure the vma is not shared, that the dst range is
* both valid and fully within a single existing vma.
*/
err = -ENOENT;
dst_vma = find_dst_vma(dst_mm, dst_start, len);
if (!dst_vma)
goto out_unlock;
err = -EINVAL;
/*
* shmem_zero_setup is invoked in mmap for MAP_ANONYMOUS|MAP_SHARED but
* it will overwrite vm_ops, so vma_is_anonymous must return false.
*/
if (WARN_ON_ONCE(vma_is_anonymous(dst_vma) &&
dst_vma->vm_flags & VM_SHARED))
goto out_unlock;
/*
* validate 'mode' now that we know the dst_vma: don't allow
* a wrprotect copy if the userfaultfd didn't register as WP.
*/
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
if ((flags & MFILL_ATOMIC_WP) && !(dst_vma->vm_flags & VM_UFFD_WP))
goto out_unlock;
/*
* If this is a HUGETLB vma, pass off to appropriate routine
*/
if (is_vm_hugetlb_page(dst_vma))
return mfill_atomic_hugetlb(dst_vma, dst_start,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
src_start, len, flags);
if (!vma_is_anonymous(dst_vma) && !vma_is_shmem(dst_vma))
goto out_unlock;
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
if (!vma_is_shmem(dst_vma) &&
uffd_flags_mode_is(flags, MFILL_ATOMIC_CONTINUE))
userfaultfd: add UFFDIO_CONTINUE ioctl This ioctl is how userspace ought to resolve "minor" userfaults. The idea is, userspace is notified that a minor fault has occurred. It might change the contents of the page using its second non-UFFD mapping, or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have ensured the page contents are correct, carry on setting up the mapping". Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in the minor fault case, we already have some pre-existing underlying page. Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping. We'd just use memcpy() or similar instead. It turns out hugetlb_mcopy_atomic_pte() already does very close to what we want, if an existing page is provided via `struct page **pagep`. We already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so just extend that design: add an enum for the three modes of operation, and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE case. (Basically, look up the existing page, and avoid adding the existing page to the page cache or calling set_page_huge_active() on it.) Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Adam Ruprecht <ruprecht@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Cannon Matthews <cannonmatthews@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chinwen Chang <chinwen.chang@mediatek.com> Cc: David Rientjes <rientjes@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: "Michal Koutn" <mkoutny@suse.com> Cc: Michel Lespinasse <walken@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shawn Anastasio <shawn@anastas.io> Cc: Steven Price <steven.price@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
goto out_unlock;
/*
* Ensure the dst_vma has a anon_vma or this page
* would get a NULL anon_vma when moved in the
* dst_vma.
*/
err = -ENOMEM;
userfaultfd: shmem: allocate anonymous memory for MAP_PRIVATE shmem Userfaultfd did not create private memory when UFFDIO_COPY was invoked on a MAP_PRIVATE shmem mapping. Instead it wrote to the shmem file, even when that had not been opened for writing. Though, fortunately, that could only happen where there was a hole in the file. Fix the shmem-backed implementation of UFFDIO_COPY to create private memory for MAP_PRIVATE mappings. The hugetlbfs-backed implementation was already correct. This change is visible to userland, if userfaultfd has been used in unintended ways: so it introduces a small risk of incompatibility, but is necessary in order to respect file permissions. An app that uses UFFDIO_COPY for anything like postcopy live migration won't notice the difference, and in fact it'll run faster because there will be no copy-on-write and memory waste in the tmpfs pagecache anymore. Userfaults on MAP_PRIVATE shmem keep triggering only on file holes like before. The real zeropage can also be built on a MAP_PRIVATE shmem mapping through UFFDIO_ZEROPAGE and that's safe because the zeropage pte is never dirty, in turn even an mprotect upgrading the vma permission from PROT_READ to PROT_READ|PROT_WRITE won't make the zeropage pte writable. Link: http://lkml.kernel.org/r/20181126173452.26955-3-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30 22:09:28 +00:00
if (!(dst_vma->vm_flags & VM_SHARED) &&
unlikely(anon_vma_prepare(dst_vma)))
goto out_unlock;
while (src_addr < src_start + len) {
pmd_t dst_pmdval;
BUG_ON(dst_addr >= dst_start + len);
dst_pmd = mm_alloc_pmd(dst_mm, dst_addr);
if (unlikely(!dst_pmd)) {
err = -ENOMEM;
break;
}
dst_pmdval = pmdp_get_lockless(dst_pmd);
/*
* If the dst_pmd is mapped as THP don't
* override it and just be strict.
*/
if (unlikely(pmd_trans_huge(dst_pmdval))) {
err = -EEXIST;
break;
}
if (unlikely(pmd_none(dst_pmdval)) &&
mm: treewide: remove unused address argument from pte_alloc functions Patch series "Add support for fast mremap". This series speeds up the mremap(2) syscall by copying page tables at the PMD level even for non-THP systems. There is concern that the extra 'address' argument that mremap passes to pte_alloc may do something subtle architecture related in the future that may make the scheme not work. Also we find that there is no point in passing the 'address' to pte_alloc since its unused. This patch therefore removes this argument tree-wide resulting in a nice negative diff as well. Also ensuring along the way that the enabled architectures do not do anything funky with the 'address' argument that goes unnoticed by the optimization. Build and boot tested on x86-64. Build tested on arm64. The config enablement patch for arm64 will be posted in the future after more testing. The changes were obtained by applying the following Coccinelle script. (thanks Julia for answering all Coccinelle questions!). Following fix ups were done manually: * Removal of address argument from pte_fragment_alloc * Removal of pte_alloc_one_fast definitions from m68k and microblaze. // Options: --include-headers --no-includes // Note: I split the 'identifier fn' line, so if you are manually // running it, please unsplit it so it runs for you. virtual patch @pte_alloc_func_def depends on patch exists@ identifier E2; identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$"; type T2; @@ fn(... - , T2 E2 ) { ... } @pte_alloc_func_proto_noarg depends on patch exists@ type T1, T2, T3, T4; identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$"; @@ ( - T3 fn(T1, T2); + T3 fn(T1); | - T3 fn(T1, T2, T4); + T3 fn(T1, T2); ) @pte_alloc_func_proto depends on patch exists@ identifier E1, E2, E4; type T1, T2, T3, T4; identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$"; @@ ( - T3 fn(T1 E1, T2 E2); + T3 fn(T1 E1); | - T3 fn(T1 E1, T2 E2, T4 E4); + T3 fn(T1 E1, T2 E2); ) @pte_alloc_func_call depends on patch exists@ expression E2; identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$"; @@ fn(... -, E2 ) @pte_alloc_macro depends on patch exists@ identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$"; identifier a, b, c; expression e; position p; @@ ( - #define fn(a, b, c) e + #define fn(a, b) e | - #define fn(a, b) e + #define fn(a) e ) Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Suggested-by: Kirill A. Shutemov <kirill@shutemov.name> Acked-by: Kirill A. Shutemov <kirill@shutemov.name> Cc: Michal Hocko <mhocko@kernel.org> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-01-03 23:28:34 +00:00
unlikely(__pte_alloc(dst_mm, dst_pmd))) {
err = -ENOMEM;
break;
}
/* If an huge pmd materialized from under us fail */
if (unlikely(pmd_trans_huge(*dst_pmd))) {
err = -EFAULT;
break;
}
BUG_ON(pmd_none(*dst_pmd));
BUG_ON(pmd_trans_huge(*dst_pmd));
err = mfill_atomic_pte(dst_pmd, dst_vma, dst_addr,
src_addr, flags, &folio);
cond_resched();
userfaultfd: use ENOENT instead of EFAULT if the atomic copy user fails Patch series "userfaultfd shmem updates". Jann found two bugs in the userfaultfd shmem MAP_SHARED backend: the lack of the VM_MAYWRITE check and the lack of i_size checks. Then looking into the above we also fixed the MAP_PRIVATE case. Hugh by source review also found a data loss source if UFFDIO_COPY is used on shmem MAP_SHARED PROT_READ mappings (the production usages incidentally run with PROT_READ|PROT_WRITE, so the data loss couldn't happen in those production usages like with QEMU). The whole patchset is marked for stable. We verified QEMU postcopy live migration with guest running on shmem MAP_PRIVATE run as well as before after the fix of shmem MAP_PRIVATE. Regardless if it's shmem or hugetlbfs or MAP_PRIVATE or MAP_SHARED, QEMU unconditionally invokes a punch hole if the guest mapping is filebacked and a MADV_DONTNEED too (needed to get rid of the MAP_PRIVATE COWs and for the anon backend). This patch (of 5): We internally used EFAULT to communicate with the caller, switch to ENOENT, so EFAULT can be used as a non internal retval. Link: http://lkml.kernel.org/r/20181126173452.26955-2-aarcange@redhat.com Fixes: 4c27fe4c4c84 ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Hugh Dickins <hughd@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Jann Horn <jannh@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-30 22:09:25 +00:00
if (unlikely(err == -ENOENT)) {
void *kaddr;
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_unlock(dst_mm);
BUG_ON(!folio);
kaddr = kmap_local_folio(folio, 0);
err = copy_from_user(kaddr,
(const void __user *) src_addr,
PAGE_SIZE);
kunmap_local(kaddr);
if (unlikely(err)) {
err = -EFAULT;
goto out;
}
flush_dcache_folio(folio);
goto retry;
} else
BUG_ON(folio);
if (!err) {
dst_addr += PAGE_SIZE;
src_addr += PAGE_SIZE;
copied += PAGE_SIZE;
if (fatal_signal_pending(current))
err = -EINTR;
}
if (err)
break;
}
out_unlock:
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_unlock(dst_mm);
out:
if (folio)
folio_put(folio);
BUG_ON(copied < 0);
BUG_ON(err > 0);
BUG_ON(!copied && !err);
return copied ? copied : err;
}
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
ssize_t mfill_atomic_copy(struct mm_struct *dst_mm, unsigned long dst_start,
unsigned long src_start, unsigned long len,
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
atomic_t *mmap_changing, uffd_flags_t flags)
{
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
return mfill_atomic(dst_mm, dst_start, src_start, len, mmap_changing,
uffd_flags_set_mode(flags, MFILL_ATOMIC_COPY));
}
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
ssize_t mfill_atomic_zeropage(struct mm_struct *dst_mm, unsigned long start,
unsigned long len, atomic_t *mmap_changing)
{
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
return mfill_atomic(dst_mm, start, 0, len, mmap_changing,
uffd_flags_set_mode(0, MFILL_ATOMIC_ZEROPAGE));
userfaultfd: add UFFDIO_CONTINUE ioctl This ioctl is how userspace ought to resolve "minor" userfaults. The idea is, userspace is notified that a minor fault has occurred. It might change the contents of the page using its second non-UFFD mapping, or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have ensured the page contents are correct, carry on setting up the mapping". Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in the minor fault case, we already have some pre-existing underlying page. Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping. We'd just use memcpy() or similar instead. It turns out hugetlb_mcopy_atomic_pte() already does very close to what we want, if an existing page is provided via `struct page **pagep`. We already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so just extend that design: add an enum for the three modes of operation, and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE case. (Basically, look up the existing page, and avoid adding the existing page to the page cache or calling set_page_huge_active() on it.) Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Adam Ruprecht <ruprecht@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Cannon Matthews <cannonmatthews@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chinwen Chang <chinwen.chang@mediatek.com> Cc: David Rientjes <rientjes@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: "Michal Koutn" <mkoutny@suse.com> Cc: Michel Lespinasse <walken@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shawn Anastasio <shawn@anastas.io> Cc: Steven Price <steven.price@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
}
mm: userfaultfd: rename functions for clarity + consistency Patch series "mm: userfaultfd: refactor and add UFFDIO_CONTINUE_MODE_WP", v5. - Commits 1-3 refactor userfaultfd ioctl code without behavior changes, with the main goal of improving consistency and reducing the number of function args. - Commit 4 adds UFFDIO_CONTINUE_MODE_WP. This patch (of 4): The basic problem is, over time we've added new userfaultfd ioctls, and we've refactored the code so functions which used to handle only one case are now re-used to deal with several cases. While this happened, we didn't bother to rename the functions. Similarly, as we added new functions, we cargo-culted pieces of the now-inconsistent naming scheme, so those functions too ended up with names that don't make a lot of sense. A key point here is, "copy" in most userfaultfd code refers specifically to UFFDIO_COPY, where we allocate a new page and copy its contents from userspace. There are many functions with "copy" in the name that don't actually do this (at least in some cases). So, rename things into a consistent scheme. The high level idea is that the call stack for userfaultfd ioctls becomes: userfaultfd_ioctl -> userfaultfd_(particular ioctl) -> mfill_atomic_(particular kind of fill operation) -> mfill_atomic /* loops over pages in range */ -> mfill_atomic_pte /* deals with single pages */ -> mfill_atomic_pte_(particular kind of fill operation) -> mfill_atomic_install_pte There are of course some special cases (shmem, hugetlb), but this is the general structure which all function names now adhere to. Link: https://lkml.kernel.org/r/20230314221250.682452-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230314221250.682452-2-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:47 +00:00
ssize_t mfill_atomic_continue(struct mm_struct *dst_mm, unsigned long start,
mm: userfaultfd: add UFFDIO_CONTINUE_MODE_WP to install WP PTEs UFFDIO_COPY already has UFFDIO_COPY_MODE_WP, so when installing a new PTE to resolve a missing fault, one can install a write-protected one. This is useful when using UFFDIO_REGISTER_MODE_{MISSING,WP} in combination. This was motivated by testing HugeTLB HGM [1], and in particular its interaction with userfaultfd features. Existing userfaultfd code supports using WP and MINOR modes together (i.e. you can register an area with both enabled), but without this CONTINUE flag the combination is in practice unusable. So, add an analogous UFFDIO_CONTINUE_MODE_WP, which does the same thing as UFFDIO_COPY_MODE_WP, but for *minor* faults. Update the selftest to do some very basic exercising of the new flag. Update Documentation/ to describe how these flags are used (neither the COPY nor the new CONTINUE versions of this mode flag were described there before). [1]: https://patchwork.kernel.org/project/linux-mm/cover/20230218002819.1486479-1-jthoughton@google.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:50 +00:00
unsigned long len, atomic_t *mmap_changing,
uffd_flags_t flags)
userfaultfd: add UFFDIO_CONTINUE ioctl This ioctl is how userspace ought to resolve "minor" userfaults. The idea is, userspace is notified that a minor fault has occurred. It might change the contents of the page using its second non-UFFD mapping, or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have ensured the page contents are correct, carry on setting up the mapping". Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in the minor fault case, we already have some pre-existing underlying page. Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping. We'd just use memcpy() or similar instead. It turns out hugetlb_mcopy_atomic_pte() already does very close to what we want, if an existing page is provided via `struct page **pagep`. We already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so just extend that design: add an enum for the three modes of operation, and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE case. (Basically, look up the existing page, and avoid adding the existing page to the page cache or calling set_page_huge_active() on it.) Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Adam Ruprecht <ruprecht@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Cannon Matthews <cannonmatthews@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chinwen Chang <chinwen.chang@mediatek.com> Cc: David Rientjes <rientjes@google.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: "Michal Koutn" <mkoutny@suse.com> Cc: Michel Lespinasse <walken@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mina Almasry <almasrymina@google.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oliver Upton <oupton@google.com> Cc: Shaohua Li <shli@fb.com> Cc: Shawn Anastasio <shawn@anastas.io> Cc: Steven Price <steven.price@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
{
mm: userfaultfd: combine 'mode' and 'wp_copy' arguments Many userfaultfd ioctl functions take both a 'mode' and a 'wp_copy' argument. In future commits we plan to plumb the flags through to more places, so we'd be proliferating the very long argument list even further. Let's take the time to simplify the argument list. Combine the two arguments into one - and generalize, so when we add more flags in the future, it doesn't imply more function arguments. Since the modes (copy, zeropage, continue) are mutually exclusive, store them as an integer value (0, 1, 2) in the low bits. Place combine-able flag bits in the high bits. This is quite similar to an earlier patch proposed by Nadav Amit ("userfaultfd: introduce uffd_flags" [1]). The main difference is that patch only handled flags, whereas this patch *also* combines the "mode" argument into the same type to shorten the argument list. [1]: https://lore.kernel.org/all/20220619233449.181323-2-namit@vmware.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-4-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: James Houghton <jthoughton@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:49 +00:00
return mfill_atomic(dst_mm, start, 0, len, mmap_changing,
mm: userfaultfd: add UFFDIO_CONTINUE_MODE_WP to install WP PTEs UFFDIO_COPY already has UFFDIO_COPY_MODE_WP, so when installing a new PTE to resolve a missing fault, one can install a write-protected one. This is useful when using UFFDIO_REGISTER_MODE_{MISSING,WP} in combination. This was motivated by testing HugeTLB HGM [1], and in particular its interaction with userfaultfd features. Existing userfaultfd code supports using WP and MINOR modes together (i.e. you can register an area with both enabled), but without this CONTINUE flag the combination is in practice unusable. So, add an analogous UFFDIO_CONTINUE_MODE_WP, which does the same thing as UFFDIO_COPY_MODE_WP, but for *minor* faults. Update the selftest to do some very basic exercising of the new flag. Update Documentation/ to describe how these flags are used (neither the COPY nor the new CONTINUE versions of this mode flag were described there before). [1]: https://patchwork.kernel.org/project/linux-mm/cover/20230218002819.1486479-1-jthoughton@google.com/ Link: https://lkml.kernel.org/r/20230314221250.682452-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-14 22:12:50 +00:00
uffd_flags_set_mode(flags, MFILL_ATOMIC_CONTINUE));
}
2020-04-07 03:06:09 +00:00
mm: userfaultfd: add new UFFDIO_POISON ioctl The basic idea here is to "simulate" memory poisoning for VMs. A VM running on some host might encounter a memory error, after which some page(s) are poisoned (i.e., future accesses SIGBUS). They expect that once poisoned, pages can never become "un-poisoned". So, when we live migrate the VM, we need to preserve the poisoned status of these pages. When live migrating, we try to get the guest running on its new host as quickly as possible. So, we start it running before all memory has been copied, and before we're certain which pages should be poisoned or not. So the basic way to use this new feature is: - On the new host, the guest's memory is registered with userfaultfd, in either MISSING or MINOR mode (doesn't really matter for this purpose). - On any first access, we get a userfaultfd event. At this point we can communicate with the old host to find out if the page was poisoned. - If so, we can respond with a UFFDIO_POISON - this places a swap marker so any future accesses will SIGBUS. Because the pte is now "present", future accesses won't generate more userfaultfd events, they'll just SIGBUS directly. UFFDIO_POISON does not handle unmapping previously-present PTEs. This isn't needed, because during live migration we want to intercept all accesses with userfaultfd (not just writes, so WP mode isn't useful for this). So whether minor or missing mode is being used (or both), the PTE won't be present in any case, so handling that case isn't needed. Similarly, UFFDIO_POISON won't replace existing PTE markers. This might be okay to do, but it seems to be safer to just refuse to overwrite any existing entry (like a UFFD_WP PTE marker). Link: https://lkml.kernel.org/r/20230707215540.2324998-5-axelrasmussen@google.com Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Gaosheng Cui <cuigaosheng1@huawei.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nadav Amit <namit@vmware.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: T.J. Alumbaugh <talumbau@google.com> Cc: Yu Zhao <yuzhao@google.com> Cc: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-07-07 21:55:36 +00:00
ssize_t mfill_atomic_poison(struct mm_struct *dst_mm, unsigned long start,
unsigned long len, atomic_t *mmap_changing,
uffd_flags_t flags)
{
return mfill_atomic(dst_mm, start, 0, len, mmap_changing,
uffd_flags_set_mode(flags, MFILL_ATOMIC_POISON));
}
long uffd_wp_range(struct vm_area_struct *dst_vma,
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
unsigned long start, unsigned long len, bool enable_wp)
{
mm/userfaultfd: rely on vma->vm_page_prot in uffd_wp_range() Patch series "mm: uffd-wp + change_protection() cleanups". Cleanup page protection handling in uffd-wp when calling change_protection() and improve unprotecting uffd=wp in private mappings, trying to set PTEs writable again if possible just like we do during mprotect() when upgrading write permissions. Make the change_protection() interface harder to get wrong :) I consider both pages primarily cleanups, although patch #1 fixes a corner case with uffd-wp and softdirty tracking for shmem. @Peter, please let me know if we should flag patch #1 as pure cleanup -- I have no idea how important softdirty tracking on shmem is. This patch (of 2): uffd_wp_range() currently calculates page protection manually using vm_get_page_prot(). This will ignore any other reason for active writenotify: one mechanism applicable to shmem is softdirty tracking. For example, the following sequence 1) Write to mapped shmem page 2) Clear softdirty 3) Register uffd-wp covering the mapped page 4) Unregister uffd-wp covering the mapped page 5) Write to page again will not set the modified page softdirty, because uffd_wp_range() will ignore that writenotify is required for softdirty tracking and simply map the page writable again using change_protection(). Similarly, instead of unregistering, protecting followed by un-protecting the page using uffd-wp would result in the same situation. Now that we enable writenotify whenever enabling uffd-wp on a VMA, vma->vm_page_prot will already properly reflect our requirements: the default is to write-protect all PTEs. However, for shared mappings we would now not remap the PTEs writable if possible when unprotecting, just like for private mappings (COW). To compensate, set MM_CP_TRY_CHANGE_WRITABLE just like mprotect() does to try mapping individual PTEs writable. For private mappings, this change implies that we will now always try setting PTEs writable when un-protecting, just like when upgrading write permissions using mprotect(), which is an improvement. For shared mappings, we will only set PTEs writable if can_change_pte_writable()/can_change_pmd_writable() indicates that it's ok. For ordinary shmem, this will be the case when PTEs are dirty, which should usually be the case -- otherwise we could special-case shmem in can_change_pte_writable()/can_change_pmd_writable() easily, because shmem itself doesn't require writenotify. Note that hugetlb does not yet implement MM_CP_TRY_CHANGE_WRITABLE, so we won't try setting PTEs writable when unprotecting or when unregistering uffd-wp. This can be added later on top by implementing MM_CP_TRY_CHANGE_WRITABLE. While commit ffd05793963a ("userfaultfd: wp: support write protection for userfault vma range") introduced that code, it should only be applicable to uffd-wp on shared mappings -- shmem (hugetlb does not support softdirty tracking). I don't think this corner cases justifies to cc stable. Let's just handle it correctly and prepare for change_protection() cleanups. [david@redhat.com: o need for additional harmless checks if we're wr-protecting either way] Link: https://lkml.kernel.org/r/71412742-a71f-9c74-865f-773ad83db7a5@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-1-david@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-2-david@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 15:56:15 +00:00
unsigned int mm_cp_flags;
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
struct mmu_gather tlb;
long ret;
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
VM_WARN_ONCE(start < dst_vma->vm_start || start + len > dst_vma->vm_end,
"The address range exceeds VMA boundary.\n");
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
if (enable_wp)
mm/userfaultfd: rely on vma->vm_page_prot in uffd_wp_range() Patch series "mm: uffd-wp + change_protection() cleanups". Cleanup page protection handling in uffd-wp when calling change_protection() and improve unprotecting uffd=wp in private mappings, trying to set PTEs writable again if possible just like we do during mprotect() when upgrading write permissions. Make the change_protection() interface harder to get wrong :) I consider both pages primarily cleanups, although patch #1 fixes a corner case with uffd-wp and softdirty tracking for shmem. @Peter, please let me know if we should flag patch #1 as pure cleanup -- I have no idea how important softdirty tracking on shmem is. This patch (of 2): uffd_wp_range() currently calculates page protection manually using vm_get_page_prot(). This will ignore any other reason for active writenotify: one mechanism applicable to shmem is softdirty tracking. For example, the following sequence 1) Write to mapped shmem page 2) Clear softdirty 3) Register uffd-wp covering the mapped page 4) Unregister uffd-wp covering the mapped page 5) Write to page again will not set the modified page softdirty, because uffd_wp_range() will ignore that writenotify is required for softdirty tracking and simply map the page writable again using change_protection(). Similarly, instead of unregistering, protecting followed by un-protecting the page using uffd-wp would result in the same situation. Now that we enable writenotify whenever enabling uffd-wp on a VMA, vma->vm_page_prot will already properly reflect our requirements: the default is to write-protect all PTEs. However, for shared mappings we would now not remap the PTEs writable if possible when unprotecting, just like for private mappings (COW). To compensate, set MM_CP_TRY_CHANGE_WRITABLE just like mprotect() does to try mapping individual PTEs writable. For private mappings, this change implies that we will now always try setting PTEs writable when un-protecting, just like when upgrading write permissions using mprotect(), which is an improvement. For shared mappings, we will only set PTEs writable if can_change_pte_writable()/can_change_pmd_writable() indicates that it's ok. For ordinary shmem, this will be the case when PTEs are dirty, which should usually be the case -- otherwise we could special-case shmem in can_change_pte_writable()/can_change_pmd_writable() easily, because shmem itself doesn't require writenotify. Note that hugetlb does not yet implement MM_CP_TRY_CHANGE_WRITABLE, so we won't try setting PTEs writable when unprotecting or when unregistering uffd-wp. This can be added later on top by implementing MM_CP_TRY_CHANGE_WRITABLE. While commit ffd05793963a ("userfaultfd: wp: support write protection for userfault vma range") introduced that code, it should only be applicable to uffd-wp on shared mappings -- shmem (hugetlb does not support softdirty tracking). I don't think this corner cases justifies to cc stable. Let's just handle it correctly and prepare for change_protection() cleanups. [david@redhat.com: o need for additional harmless checks if we're wr-protecting either way] Link: https://lkml.kernel.org/r/71412742-a71f-9c74-865f-773ad83db7a5@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-1-david@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-2-david@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 15:56:15 +00:00
mm_cp_flags = MM_CP_UFFD_WP;
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
else
mm/userfaultfd: rely on vma->vm_page_prot in uffd_wp_range() Patch series "mm: uffd-wp + change_protection() cleanups". Cleanup page protection handling in uffd-wp when calling change_protection() and improve unprotecting uffd=wp in private mappings, trying to set PTEs writable again if possible just like we do during mprotect() when upgrading write permissions. Make the change_protection() interface harder to get wrong :) I consider both pages primarily cleanups, although patch #1 fixes a corner case with uffd-wp and softdirty tracking for shmem. @Peter, please let me know if we should flag patch #1 as pure cleanup -- I have no idea how important softdirty tracking on shmem is. This patch (of 2): uffd_wp_range() currently calculates page protection manually using vm_get_page_prot(). This will ignore any other reason for active writenotify: one mechanism applicable to shmem is softdirty tracking. For example, the following sequence 1) Write to mapped shmem page 2) Clear softdirty 3) Register uffd-wp covering the mapped page 4) Unregister uffd-wp covering the mapped page 5) Write to page again will not set the modified page softdirty, because uffd_wp_range() will ignore that writenotify is required for softdirty tracking and simply map the page writable again using change_protection(). Similarly, instead of unregistering, protecting followed by un-protecting the page using uffd-wp would result in the same situation. Now that we enable writenotify whenever enabling uffd-wp on a VMA, vma->vm_page_prot will already properly reflect our requirements: the default is to write-protect all PTEs. However, for shared mappings we would now not remap the PTEs writable if possible when unprotecting, just like for private mappings (COW). To compensate, set MM_CP_TRY_CHANGE_WRITABLE just like mprotect() does to try mapping individual PTEs writable. For private mappings, this change implies that we will now always try setting PTEs writable when un-protecting, just like when upgrading write permissions using mprotect(), which is an improvement. For shared mappings, we will only set PTEs writable if can_change_pte_writable()/can_change_pmd_writable() indicates that it's ok. For ordinary shmem, this will be the case when PTEs are dirty, which should usually be the case -- otherwise we could special-case shmem in can_change_pte_writable()/can_change_pmd_writable() easily, because shmem itself doesn't require writenotify. Note that hugetlb does not yet implement MM_CP_TRY_CHANGE_WRITABLE, so we won't try setting PTEs writable when unprotecting or when unregistering uffd-wp. This can be added later on top by implementing MM_CP_TRY_CHANGE_WRITABLE. While commit ffd05793963a ("userfaultfd: wp: support write protection for userfault vma range") introduced that code, it should only be applicable to uffd-wp on shared mappings -- shmem (hugetlb does not support softdirty tracking). I don't think this corner cases justifies to cc stable. Let's just handle it correctly and prepare for change_protection() cleanups. [david@redhat.com: o need for additional harmless checks if we're wr-protecting either way] Link: https://lkml.kernel.org/r/71412742-a71f-9c74-865f-773ad83db7a5@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-1-david@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-2-david@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 15:56:15 +00:00
mm_cp_flags = MM_CP_UFFD_WP_RESOLVE;
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
mm/userfaultfd: rely on vma->vm_page_prot in uffd_wp_range() Patch series "mm: uffd-wp + change_protection() cleanups". Cleanup page protection handling in uffd-wp when calling change_protection() and improve unprotecting uffd=wp in private mappings, trying to set PTEs writable again if possible just like we do during mprotect() when upgrading write permissions. Make the change_protection() interface harder to get wrong :) I consider both pages primarily cleanups, although patch #1 fixes a corner case with uffd-wp and softdirty tracking for shmem. @Peter, please let me know if we should flag patch #1 as pure cleanup -- I have no idea how important softdirty tracking on shmem is. This patch (of 2): uffd_wp_range() currently calculates page protection manually using vm_get_page_prot(). This will ignore any other reason for active writenotify: one mechanism applicable to shmem is softdirty tracking. For example, the following sequence 1) Write to mapped shmem page 2) Clear softdirty 3) Register uffd-wp covering the mapped page 4) Unregister uffd-wp covering the mapped page 5) Write to page again will not set the modified page softdirty, because uffd_wp_range() will ignore that writenotify is required for softdirty tracking and simply map the page writable again using change_protection(). Similarly, instead of unregistering, protecting followed by un-protecting the page using uffd-wp would result in the same situation. Now that we enable writenotify whenever enabling uffd-wp on a VMA, vma->vm_page_prot will already properly reflect our requirements: the default is to write-protect all PTEs. However, for shared mappings we would now not remap the PTEs writable if possible when unprotecting, just like for private mappings (COW). To compensate, set MM_CP_TRY_CHANGE_WRITABLE just like mprotect() does to try mapping individual PTEs writable. For private mappings, this change implies that we will now always try setting PTEs writable when un-protecting, just like when upgrading write permissions using mprotect(), which is an improvement. For shared mappings, we will only set PTEs writable if can_change_pte_writable()/can_change_pmd_writable() indicates that it's ok. For ordinary shmem, this will be the case when PTEs are dirty, which should usually be the case -- otherwise we could special-case shmem in can_change_pte_writable()/can_change_pmd_writable() easily, because shmem itself doesn't require writenotify. Note that hugetlb does not yet implement MM_CP_TRY_CHANGE_WRITABLE, so we won't try setting PTEs writable when unprotecting or when unregistering uffd-wp. This can be added later on top by implementing MM_CP_TRY_CHANGE_WRITABLE. While commit ffd05793963a ("userfaultfd: wp: support write protection for userfault vma range") introduced that code, it should only be applicable to uffd-wp on shared mappings -- shmem (hugetlb does not support softdirty tracking). I don't think this corner cases justifies to cc stable. Let's just handle it correctly and prepare for change_protection() cleanups. [david@redhat.com: o need for additional harmless checks if we're wr-protecting either way] Link: https://lkml.kernel.org/r/71412742-a71f-9c74-865f-773ad83db7a5@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-1-david@redhat.com Link: https://lkml.kernel.org/r/20221223155616.297723-2-david@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-12-23 15:56:15 +00:00
/*
* vma->vm_page_prot already reflects that uffd-wp is enabled for this
* VMA (see userfaultfd_set_vm_flags()) and that all PTEs are supposed
* to be write-protected as default whenever protection changes.
* Try upgrading write permissions manually.
*/
if (!enable_wp && vma_wants_manual_pte_write_upgrade(dst_vma))
mm_cp_flags |= MM_CP_TRY_CHANGE_WRITABLE;
tlb_gather_mmu(&tlb, dst_vma->vm_mm);
ret = change_protection(&tlb, dst_vma, start, start + len, mm_cp_flags);
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
tlb_finish_mmu(&tlb);
return ret;
mm/uffd: reset write protection when unregister with wp-mode The motivation of this patch comes from a recent report and patchfix from David Hildenbrand on hugetlb shared handling of wr-protected page [1]. With the reproducer provided in commit message of [1], one can leverage the uffd-wp lazy-reset of ptes to trigger a hugetlb issue which can affect not only the attacker process, but also the whole system. The lazy-reset mechanism of uffd-wp was used to make unregister faster, meanwhile it has an assumption that any leftover pgtable entries should only affect the process on its own, so not only the user should be aware of anything it does, but also it should not affect outside of the process. But it seems that this is not true, and it can also be utilized to make some exploit easier. So far there's no clue showing that the lazy-reset is important to any userfaultfd users because normally the unregister will only happen once for a specific range of memory of the lifecycle of the process. Considering all above, what this patch proposes is to do explicit pte resets when unregister an uffd region with wr-protect mode enabled. It should be the same as calling ioctl(UFFDIO_WRITEPROTECT, wp=false) right before ioctl(UFFDIO_UNREGISTER) for the user. So potentially it'll make the unregister slower. From that pov it's a very slight abi change, but hopefully nothing should break with this change either. Regarding to the change itself - core of uffd write [un]protect operation is moved into a separate function (uffd_wp_range()) and it is reused in the unregister code path. Note that the new function will not check for anything, e.g. ranges or memory types, because they should have been checked during the previous UFFDIO_REGISTER or it should have failed already. It also doesn't check mmap_changing because we're with mmap write lock held anyway. I added a Fixes upon introducing of uffd-wp shmem+hugetlbfs because that's the only issue reported so far and that's the commit David's reproducer will start working (v5.19+). But the whole idea actually applies to not only file memories but also anonymous. It's just that we don't need to fix anonymous prior to v5.19- because there's no known way to exploit. IOW, this patch can also fix the issue reported in [1] as the patch 2 does. [1] https://lore.kernel.org/all/20220811103435.188481-3-david@redhat.com/ Link: https://lkml.kernel.org/r/20220811201340.39342-1-peterx@redhat.com Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs") Signed-off-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-08-11 20:13:40 +00:00
}
2020-04-07 03:06:09 +00:00
int mwriteprotect_range(struct mm_struct *dst_mm, unsigned long start,
userfaultfd: change mmap_changing to atomic Patch series "userfaultfd: minor bug fixes". Three unrelated bug fixes. The first two addresses possible issues (not too theoretical ones), but I did not encounter them in practice. The third patch addresses a test bug that causes the test to fail on my system. It has been sent before as part of a bigger RFC. This patch (of 3): mmap_changing is currently a boolean variable, which is set and cleared without any lock that protects against concurrent modifications. mmap_changing is supposed to mark whether userfaultfd page-faults handling should be retried since mappings are undergoing a change. However, concurrent calls, for instance to madvise(MADV_DONTNEED), might cause mmap_changing to be false, although the remove event was still not read (hence acknowledged) by the user. Change mmap_changing to atomic_t and increase/decrease appropriately. Add a debug assertion to see whether mmap_changing is negative. Link: https://lkml.kernel.org/r/20210808020724.1022515-1-namit@vmware.com Link: https://lkml.kernel.org/r/20210808020724.1022515-2-namit@vmware.com Fixes: df2cc96e77011 ("userfaultfd: prevent non-cooperative events vs mcopy_atomic races") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-09-02 21:58:56 +00:00
unsigned long len, bool enable_wp,
atomic_t *mmap_changing)
2020-04-07 03:06:09 +00:00
{
unsigned long end = start + len;
unsigned long _start, _end;
2020-04-07 03:06:09 +00:00
struct vm_area_struct *dst_vma;
unsigned long page_mask;
long err;
VMA_ITERATOR(vmi, dst_mm, start);
2020-04-07 03:06:09 +00:00
/*
* Sanitize the command parameters:
*/
BUG_ON(start & ~PAGE_MASK);
BUG_ON(len & ~PAGE_MASK);
/* Does the address range wrap, or is the span zero-sized? */
BUG_ON(start + len <= start);
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_lock(dst_mm);
2020-04-07 03:06:09 +00:00
/*
* If memory mappings are changing because of non-cooperative
* operation (e.g. mremap) running in parallel, bail out and
* request the user to retry later
*/
err = -EAGAIN;
userfaultfd: change mmap_changing to atomic Patch series "userfaultfd: minor bug fixes". Three unrelated bug fixes. The first two addresses possible issues (not too theoretical ones), but I did not encounter them in practice. The third patch addresses a test bug that causes the test to fail on my system. It has been sent before as part of a bigger RFC. This patch (of 3): mmap_changing is currently a boolean variable, which is set and cleared without any lock that protects against concurrent modifications. mmap_changing is supposed to mark whether userfaultfd page-faults handling should be retried since mappings are undergoing a change. However, concurrent calls, for instance to madvise(MADV_DONTNEED), might cause mmap_changing to be false, although the remove event was still not read (hence acknowledged) by the user. Change mmap_changing to atomic_t and increase/decrease appropriately. Add a debug assertion to see whether mmap_changing is negative. Link: https://lkml.kernel.org/r/20210808020724.1022515-1-namit@vmware.com Link: https://lkml.kernel.org/r/20210808020724.1022515-2-namit@vmware.com Fixes: df2cc96e77011 ("userfaultfd: prevent non-cooperative events vs mcopy_atomic races") Signed-off-by: Nadav Amit <namit@vmware.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-09-02 21:58:56 +00:00
if (mmap_changing && atomic_read(mmap_changing))
2020-04-07 03:06:09 +00:00
goto out_unlock;
err = -ENOENT;
for_each_vma_range(vmi, dst_vma, end) {
if (!userfaultfd_wp(dst_vma)) {
err = -ENOENT;
break;
}
2020-04-07 03:06:09 +00:00
if (is_vm_hugetlb_page(dst_vma)) {
err = -EINVAL;
page_mask = vma_kernel_pagesize(dst_vma) - 1;
if ((start & page_mask) || (len & page_mask))
break;
}
_start = max(dst_vma->vm_start, start);
_end = min(dst_vma->vm_end, end);
err = uffd_wp_range(dst_vma, _start, _end - _start, enable_wp);
2020-04-07 03:06:09 +00:00
/* Return 0 on success, <0 on failures */
if (err < 0)
break;
err = 0;
}
2020-04-07 03:06:09 +00:00
out_unlock:
mmap locking API: use coccinelle to convert mmap_sem rwsem call sites This change converts the existing mmap_sem rwsem calls to use the new mmap locking API instead. The change is generated using coccinelle with the following rule: // spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir . @@ expression mm; @@ ( -init_rwsem +mmap_init_lock | -down_write +mmap_write_lock | -down_write_killable +mmap_write_lock_killable | -down_write_trylock +mmap_write_trylock | -up_write +mmap_write_unlock | -downgrade_write +mmap_write_downgrade | -down_read +mmap_read_lock | -down_read_killable +mmap_read_lock_killable | -down_read_trylock +mmap_read_trylock | -up_read +mmap_read_unlock ) -(&mm->mmap_sem) +(mm) Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jerome Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ying Han <yinghan@google.com> Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-06-09 04:33:25 +00:00
mmap_read_unlock(dst_mm);
2020-04-07 03:06:09 +00:00
return err;
}